File size: 3,605 Bytes
b24351f |
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 |
{
"ticketNumber" : "892735",
"reporterName" : "BAKE KI",
"rankPoints" : "80",
"resolutionStatus" : "TI Thinks Resolved",
"ticketName" : "LM5176-Q1: Is there a way to charge 3A CC-mode? -LM5176-Q1",
"rankName" : "Prodigy",
"replies" : " 5",
"views" : " 35",
"queryText" : "Part Number: LM5176-Q1 I will design a battery charging circuit with the LM5176. I want to charge 3A CC-mode, is it possible? If Hiccup or Average Current Limit is off, the current will flow over 3A without limitation. And if I turn on the two functions, I think that the current will rise and the charging will end at 3A. In general, the battery will be charged by CC-CV, so the cut-off time will be very short. I cannot use Chager IC because I have to use AEC-Q100 certified product. As far as I know, BQ24616 etc. do not have AEC-Q100. Is there a way to charge 3A CC-mode? Vin: 10 ~ 16V, Vout: 14.6V / 3A, and there is an immutable fuse in the Vin line, so you must limit the current.",
"partNumber" : " LM5176-Q1",
"allResponseList" : [ {
"contentId" : "3301123",
"userName" : "Garrett Roecker",
"rankPoints" : "18240",
"rankName" : "Mastermind",
"date" : "Mar 30, 2020 6:09 PM",
"userId" : "3456925",
"content" : "Hi BAKE KI, Thank you for reaching out with your question and for considering the LM5176 in your design. The LM5176 can be configured to output a constant current using the average current limiting feature. Placing a resistor between the ISNS+ and ISNS- pin will limit the current when the voltage drop across the resistor is 50mV. Please let me know if you have any other questions. Thanks, Garrett"
}, {
"contentId" : "3301627",
"userName" : "BAKE KI",
"rankPoints" : "80",
"rankName" : "Prodigy",
"date" : "Mar 31, 2020 5:59 AM",
"userId" : "1929261",
"content" : "Thank you so much for answering. The battery capacity is 7.2 Ah. What resistance should I use for 3A CC charging? If you use 0.015 ohm for the sensing resistance between ISNS + and ISNS -... Is 45mV when charging at 3A, and 51mV at 3.4A to cut off the current? If it is correct ... I think that as soon as the charging starts, the current will flow more than 3.4A, and the charging will end within a few seconds."
}, {
"contentId" : "3304170",
"userName" : "Garrett Roecker",
"rankPoints" : "18240",
"rankName" : "Mastermind",
"date" : "Apr 1, 2020 10:15 PM",
"userId" : "3456925",
"content" : "Hi BAKE KI, It is possible to add multiple resistors in parallel to set a static current limit for the average output current. 17mOhm will set the typical output current to 3A Please let me know if you have any questions. Thanks, Garrett"
}, {
"contentId" : "3328570",
"userName" : "BAKE KI",
"rankPoints" : "80",
"rankName" : "Prodigy",
"date" : "Apr 27, 2020 10:02 AM",
"userId" : "1929261",
"content" : "3.3A CC-Mode operation was confirmed by applying a 15mΩ resistor. All thanks to you. Can the input current be maintained at 3A by changing the 15mΩ resistor position to Input?"
}, {
"contentId" : "3329580",
"userName" : "Garrett Roecker",
"rankPoints" : "18240",
"rankName" : "Mastermind",
"date" : "Apr 27, 2020 10:36 PM",
"userId" : "3456925",
"content" : "BAKE KI, Yes moving the resistor to the input voltage rail will be used to limit the input current. Thanks, Garrett"
} ],
"tags" : [ "/support/power-management/f/196/tags/bq24616", "/support/power-management/f/196/tags/LM5176", "/support/power-management/f/196/tags/LM5176_2D00_Q1" ],
"fourmType" : "TI"
} |