data/text/DLP1/899536

CCS/UCD3138A: question about DPWM3 Interrupt

Part Number: UCD3138A Tool/software: Code Composer Studio The DPWM3 initialized code as follow: // Control-0 Dpwm3Regs.DPWMCTRL0.bit.PWM_EN = 1; // Enable, wait for Global En Dpwm3Regs.DPWMCTRL0.bit.CLA_EN = 0; // CLA Disabled, using curr limit to chop Dpwm3Regs.DPWMCTRL0.bit.PWM_MODE = 0; // Set mode: 0 - Normal Dpwm3Regs.DPWMCTRL0.bit.MSYNC_SLAVE_EN = 1; // slave Dpwm3Regs.DPWMCTRL0.bit.CBC_ADV_CNT_EN = 0; // Adv cnt limit enabled Dpwm3Regs.DPWMCTRL0.bit.CBC_PWM_AB_EN = 0; // Current limit enabled for AB outputs Dpwm3Regs.DPWMCTRL0.bit.PWM_A_INTRA_MUX = 0; Dpwm3Regs.DPWMCTRL0.bit.PWM_B_INTRA_MUX = 0; Dpwm3Regs.DPWMCTRL0.bit.BLANK_A_EN = 1; // Control-1 Dpwm3Regs.DPWMCTRL1.bit.HIRES_DIS = 1; //Dpwm3Regs.DPWMCTRL1.bit.ALL_PHASE_CLK_ENA = 1; Dpwm3Regs.DPWMCTRL1.bit.CHECK_OVERRIDE = 1; Dpwm3Regs.DPWMCTRL1.bit.EVENT_UP_SEL = 1; // UPdate end of period Dpwm3Regs.DPWMEV1.all = DPWM3_EVT1; Dpwm3Regs.DPWMEV2.all = DPWM3_EVT2; Dpwm3Regs.DPWMEV3.all = DPWM3_EVT3; Dpwm3Regs.DPWMEV4.all = DPWM3_EVT4; Dpwm3Regs.DPWMPRD.all = (PWM_PERIOD>>1); Dpwm3Regs.DPWMINT.bit.PRD_INT_SCALE = 2; //every 4 cycles primary(PRD_INT_SCALE = 2) Dpwm3Regs.DPWMINT.bit.PRD_INT_EN = 1; But I find that the dpwm3 interrupt don't happen. I use the PMbus protocol and debug_IO toggle to see it. The fir number is 26 in the fast interrupt. It need your help. Thanks!

Hi Liwei, In order for interrupt to work you need to enable it in 3 levels. 1) In the peripheral (DPWM3) level (You are already showing this part being done) 2) In the CIM level by calling the two functions: //Configure IRQ write_reqmask(CIMINT_ALL_PWM2_COMP | CIMINT_ALL_DPWM3); //Configure FIQ write_firqpr(CIMINT_ALL_DPWM3); 3) And finally at the global (ARM7) level by calling the two functions: //Enable interrupts enable_fast_interrupt(); enable_interrupt(); So please first verify that all 3 steps are complete. If all the above does not work, please check fiq number 27 instead of 26. Regards, Yitzhak

Hi, Yitzhak: Thank you very much! You are right. I forget to set the register of IRQ. I change the firmware, but only set the IRQ and not set the FIQ. Then UCD3138 could not program again. I write 0x5a5a with command 0xD8 to it. It return NACK. Why? How can I save UCD3138 to program again?

Hi Liwei, Glad it helped. If you mean to write into IRQ register, this can only be done in ARM7 privileged mode and not in user mode. That is why the "functions" write_firqpr() and write_reqmask() are implemented by software interrupt and not as ordinary functions. Just change the parameters in the calls to the above two functions instead. Regards,

Hi,Yitzhak: Thank you!