|
{ |
|
"ticketNumber" : "892735", |
|
"reporterName" : "BAKE KI", |
|
"rankPoints" : "80", |
|
"resolutionStatus" : "TI Thinks Resolved", |
|
"ticketName" : "LM5176-Q1: Is there a way to charge 3A CC-mode? -LM5176-Q1", |
|
"rankName" : "Prodigy", |
|
"replies" : " 5", |
|
"views" : " 35", |
|
"queryText" : "Part Number: LM5176-Q1 I will design a battery charging circuit with the LM5176. I want to charge 3A CC-mode, is it possible? If Hiccup or Average Current Limit is off, the current will flow over 3A without limitation. And if I turn on the two functions, I think that the current will rise and the charging will end at 3A. In general, the battery will be charged by CC-CV, so the cut-off time will be very short. I cannot use Chager IC because I have to use AEC-Q100 certified product. As far as I know, BQ24616 etc. do not have AEC-Q100. Is there a way to charge 3A CC-mode? Vin: 10 ~ 16V, Vout: 14.6V / 3A, and there is an immutable fuse in the Vin line, so you must limit the current.", |
|
"partNumber" : " LM5176-Q1", |
|
"allResponseList" : [ { |
|
"contentId" : "3301123", |
|
"userName" : "Garrett Roecker", |
|
"rankPoints" : "18240", |
|
"rankName" : "Mastermind", |
|
"date" : "Mar 30, 2020 6:09 PM", |
|
"userId" : "3456925", |
|
"content" : "Hi BAKE KI, Thank you for reaching out with your question and for considering the LM5176 in your design. The LM5176 can be configured to output a constant current using the average current limiting feature. Placing a resistor between the ISNS+ and ISNS- pin will limit the current when the voltage drop across the resistor is 50mV. Please let me know if you have any other questions. Thanks, Garrett" |
|
}, { |
|
"contentId" : "3301627", |
|
"userName" : "BAKE KI", |
|
"rankPoints" : "80", |
|
"rankName" : "Prodigy", |
|
"date" : "Mar 31, 2020 5:59 AM", |
|
"userId" : "1929261", |
|
"content" : "Thank you so much for answering. The battery capacity is 7.2 Ah. What resistance should I use for 3A CC charging? If you use 0.015 ohm for the sensing resistance between ISNS + and ISNS -... Is 45mV when charging at 3A, and 51mV at 3.4A to cut off the current? If it is correct ... I think that as soon as the charging starts, the current will flow more than 3.4A, and the charging will end within a few seconds." |
|
}, { |
|
"contentId" : "3304170", |
|
"userName" : "Garrett Roecker", |
|
"rankPoints" : "18240", |
|
"rankName" : "Mastermind", |
|
"date" : "Apr 1, 2020 10:15 PM", |
|
"userId" : "3456925", |
|
"content" : "Hi BAKE KI, It is possible to add multiple resistors in parallel to set a static current limit for the average output current. 17mOhm will set the typical output current to 3A Please let me know if you have any questions. Thanks, Garrett" |
|
}, { |
|
"contentId" : "3328570", |
|
"userName" : "BAKE KI", |
|
"rankPoints" : "80", |
|
"rankName" : "Prodigy", |
|
"date" : "Apr 27, 2020 10:02 AM", |
|
"userId" : "1929261", |
|
"content" : "3.3A CC-Mode operation was confirmed by applying a 15mΩ resistor. All thanks to you. Can the input current be maintained at 3A by changing the 15mΩ resistor position to Input?" |
|
}, { |
|
"contentId" : "3329580", |
|
"userName" : "Garrett Roecker", |
|
"rankPoints" : "18240", |
|
"rankName" : "Mastermind", |
|
"date" : "Apr 27, 2020 10:36 PM", |
|
"userId" : "3456925", |
|
"content" : "BAKE KI, Yes moving the resistor to the input voltage rail will be used to limit the input current. Thanks, Garrett" |
|
} ], |
|
"tags" : [ "/support/power-management/f/196/tags/bq24616", "/support/power-management/f/196/tags/LM5176", "/support/power-management/f/196/tags/LM5176_2D00_Q1" ], |
|
"fourmType" : "TI" |
|
} |