|
Part Number: TDA2EVM5777 Other Parts Discussed in Thread: TDA2, DRA742, PCF8575, PMP, DRA752 HI,I met the problem,my EVM is TDA2 XC5777X,I check the SD card of CD is no connect,dra7-evm.dts define evm_3v3_sd: fixedregulator-sd { compatible = "regulator-fixed"; regulator-name = "evm_3v3_sd"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; enable-active-high; gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>; }; &mmc1 { status = "okay"; vmmc-supply = <&evm_3v3_sd>; vmmc_aux-supply = <&ldo1_reg>; bus-width = <4>; /* * SDCD signal is not being used here - using the fact that GPIO mode * is always hardwired. */ cd-gpios = <&gpio6 27 GPIO_ACTIVE_HIGH>; max-frequency = <192000000>; pinctrl-names = "default", "hs", "sdr12", "sdr25", "sdr50", "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104"; pinctrl-0 = <&mmc1_pins_default>; pinctrl-1 = <&mmc1_pins_hs>; pinctrl-2 = <&mmc1_pins_sdr12>; pinctrl-3 = <&mmc1_pins_sdr25>; pinctrl-4 = <&mmc1_pins_sdr50>; pinctrl-5 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr50_rev11_conf>; pinctrl-6 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev11_conf>; pinctrl-7 = <&mmc1_pins_ddr50 &mmc1_iodelay_ddr50_rev20_conf>; pinctrl-8 = <&mmc1_pins_sdr104 &mmc1_iodelay_sdr104_rev20_conf>; }; next is my report log/**************************************************************************************************/ U-Boot SPL 2016.05 (May 07 2019 - 10:44:23) DRA752-GP ES2.0 no pinctrl for hs200_1_8v no pinctrl for ddr_1_8v ** First descriptor is NOT a primary desc on 1:1 ** Trying to boot from MMC1 reading dra7-ipu2-fw.lzop spl_load_file_fat: error reading file dra7-ipu2-fw.lzop, err - -1 spl: error reading image dra7-ipu2-fw.lzop, err - -1 Error loading remotecore IPU2!,Continuing with boot ... reading dra7-dsp1-fw.lzop spl_load_file_fat: error reading file dra7-dsp1-fw.lzop, err - -1 spl: error reading image dra7-dsp1-fw.lzop, err - -1 Error loading remotecore DSP1!,Continuing with boot ... reading dra7-dsp2-fw.lzop spl_load_file_fat: error reading file dra7-dsp2-fw.lzop, err - -1 spl: error reading image dra7-dsp2-fw.lzop, err - -1 Error loading remotecore DSP2!,Continuing with boot ... reading dra7-ipu1-fw.lzop spl_load_file_fat: error reading file dra7-ipu1-fw.lzop, err - -1 spl: error reading image dra7-ipu1-fw.lzop, err - -1 Error loading remotecore IPU1!,Continuing with boot ... reading u-boot.img reading u-boot.img reading u-boot.img reading u-boot.img U-Boot 2016.05 (May 07 2019 - 10:44:23 +0800) CPU : DRA752-GP ES2.0 Model: TI DRA742 Board: DRA74x EVM REV G.0 DRAM: 1.5 GiB MMC: i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 OMAP SD/MMC: 0, OMAP SD/MMC: 1 ** First descriptor is NOT a primary desc on 1:1 ** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid GPT *** GUID Partition Table Header signature is wrong: 0x0 != 0x5452415020494645 part_get_info_efi: *** ERROR: Invalid Backup GPT *** ERROR: cannot find partition: 'userdata' at arch/arm/cpu/armv7/omap-common/utils.c:199/mmc_get_part_size() Warning: fastboot.userdata_size: unable to calc SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 ## Error: "board_findfdt" not defined i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 reading boot.scr ** Unable to read file boot.scr ** reading uEnv.txt 173 bytes read in 2 ms (84 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 switch to partitions #0, OK mmc0 is current device i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 i2c_write: error waiting for data ACK (status=0x116) pcf8575_i2c_write_le16 i2c write failed to addr 21 SD/MMC found on device 0 3576504 bytes read in 188 ms (18.1 MiB/s) 106947 bytes read in 35 ms (2.9 MiB/s) Booting from mmc0 ... Kernel image @ 0x82000000 [ 0x000000 - 0x3692b8 ] ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffe2000, end 8ffff1c2 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.84-00038-g0af2ab562143 (zhj@zhj) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #3 SMP PREEMPT Mon Jan 6 16:31:50 CST 2020 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: TI DRA742 [ 0.000000] Reserved memory: created DMA memory pool at 0x0000000040300000, size 3 MiB [ 0.000000] Reserved memory: initialized node cmem@40300000, compatible id shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000099000000, size 80 MiB [ 0.000000] Reserved memory: initialized node ipu2_cma@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009e000000, size 32 MiB [ 0.000000] Reserved memory: initialized node ipu1_cma@9d000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a1000000, size 32 MiB [ 0.000000] Reserved memory: initialized node dsp1_cma@99000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x00000000a3000000, size 32 MiB [ 0.000000] Reserved memory: initialized node dsp2_cma@9f000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: regions without no-map are not yet supported [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a9000000, size 32 MiB [ 0.000000] Reserved memory: initialized node cmem@A9000000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 64 MiB at 0x00000000bbc00000 [ 0.000000] Forcing write-allocate cache policy for SMP [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] OMAP4: Map 0x00000000bfd00000 to fe600000 for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] PERCPU: Embedded 11 pages/cpu @ef62a000 s14912 r8192 d21952 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 251456 [ 0.000000] Kernel command line: console=ttyO0,115200n8 vram=16M root=PARTUUID=f724ed05-02 rw rootwait ip=none mem=1024M cma=64M [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 353148K/1012736K available (6671K kernel code, 320K rwdata, 2396K rodata, 336K init, 290K bss, 413828K reserved, 245760K cma-reserved, 193536K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08e302c (9069 kB) [ 0.000000] .init : 0xc08e4000 - 0xc0938000 ( 336 kB) [ 0.000000] .data : 0xc0938000 - 0xc0988220 ( 321 kB) [ 0.000000] .bss : 0xc098a000 - 0xc09d2880 ( 291 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] ti_dt_clocks_register: failed to lookup clock node gmac_gmii_ref_clk_div [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] Architected cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000015] Switching to timer-based delay loop, resolution 162ns [ 0.000330] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000338] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000775] Console: colour dummy device 80x30 [ 0.000791] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' [ 0.000797] This ensures that you still see kernel messages. Please [ 0.000803] update your kernel commandline. [ 0.000817] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000829] pid_max: default: 32768 minimum: 301 [ 0.000930] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000940] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001482] Initializing cgroup subsys io [ 0.001497] Initializing cgroup subsys memory [ 0.001521] Initializing cgroup subsys devices [ 0.001534] Initializing cgroup subsys freezer [ 0.001545] Initializing cgroup subsys perf_event [ 0.001557] Initializing cgroup subsys pids [ 0.001583] CPU: Testing write buffer coherency: ok [ 0.001782] /cpus/cpu@0 missing clock-frequency property [ 0.001798] /cpus/cpu@1 missing clock-frequency property [ 0.001808] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001841] Setting up static identity map for 0x80008380 - 0x800083e0 [ 0.080065] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.080133] Brought up 2 CPUs [ 0.080146] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.080152] CPU: All CPU(s) started in HYP mode. [ 0.080158] CPU: Virtualization extensions available. [ 0.080531] devtmpfs: initialized [ 0.109110] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.110083] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.312832] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.312854] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.317812] pinctrl core: initialized pinctrl subsystem [ 0.318678] NET: Registered protocol family 16 [ 0.319626] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.350232] cpuidle: using governor ladder [ 0.380256] cpuidle: using governor menu [ 0.388788] OMAP GPIO hardware version 0.1 [ 0.395274] irq: no irq domain found for /ocp/l4@4a000000/scm@2000/pinmux@1400 ! [ 0.411836] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.411848] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000 [ 0.420434] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.420444] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.420922] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.420932] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.421516] OMAP DMA hardware revision 0.0 [ 0.461718] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.462870] edma 43300000.edma: memcpy is disabled [ 0.467671] edma 43300000.edma: TI EDMA DMA engine driver [ 0.472089] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.472266] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.472428] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.472585] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.472881] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.473069] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.476064] palmas 0-0058: IRQ missing: skipping irq request [ 0.490827] palmas 0-0058: Muxing GPIO 2e, PWM 0, LED 0 [ 0.563148] pcf857x 0-0020: probed [ 0.563394] pcf857x: probe of 0-0021 failed with error -121 [ 0.563555] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 0.563951] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 0.564154] media: Linux media interface: v0.10 [ 0.564205] Linux video capture interface: v2.00 [ 0.564251] pps_core: LinuxPPS API ver. 1 registered [ 0.564258] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]> [ 0.564283] PTP clock support registered [ 0.564335] EDAC MC: Ver: 3.0.0 [ 0.565083] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.565385] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.565718] Advanced Linux Sound Architecture Driver Initialized. [ 0.566582] clocksource: Switched to clocksource arch_sys_counter [ 0.577150] NET: Registered protocol family 2 [ 0.577643] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.577707] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.577832] TCP: Hash tables configured (established 8192 bind 8192) [ 0.577879] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.577910] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.578115] NET: Registered protocol family 1 [ 0.578381] RPC: Registered named UNIX socket transport module. [ 0.578389] RPC: Registered udp transport module. [ 0.578396] RPC: Registered tcp transport module. [ 0.578402] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.579419] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.589494] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.590151] NFS: Registering the id_resolver key type [ 0.590177] Key type id_resolver registered [ 0.590184] Key type id_legacy registered [ 0.590242] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.591529] bounce: pool size: 64 pages [ 0.591679] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 0.591694] io scheduler noop registered [ 0.591707] io scheduler deadline registered [ 0.591740] io scheduler cfq registered (default) [ 0.596680] pinctrl-single 4a003400.pinmux: 282 pins at pa fc003400 size 1128 [ 0.599862] PCI host bridge /ocp/axi@0/pcie_rc@51000000 ranges: [ 0.599874] No bus range found for /ocp/axi@0/pcie_rc@51000000, using [bus 00-ff] [ 0.599908] IO 0x20003000..0x20012fff -> 0x00000000 [ 0.599929] MEM 0x20013000..0x2fffffff -> 0x20013000 [ 0.629795] dra7-pcie 51000000.pcie_rc: link is not up [ 0.629969] dra7-pcie 51000000.pcie_rc: PCI host bridge to bus 0000:00 [ 0.629981] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.629992] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.630001] pci_bus 0000:00: root bus resource [mem 0x20013000-0x2fffffff] [ 0.630398] PCI: bus0: Fast back to back transfers disabled [ 0.630520] PCI: bus1: Fast back to back transfers enabled [ 0.630602] pci 0000:00:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 0.630617] pci 0000:00:00.0: BAR 1: assigned [mem 0x20020000-0x2002ffff] [ 0.630629] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.630855] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 0.691124] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled [ 0.694523] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 301, base_baud = 3000000) is a 8250 [ 1.705923] console [ttyS0] enabled [ 1.710330] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 302, base_baud = 3000000) is a 8250 [ 1.720035] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 303, base_baud = 3000000) is a 8250 [ 1.730081] [drm] Initialized drm 1.1.0 20060810 [ 1.735602] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.742290] [drm] No driver support for vblank timestamp query. [ 1.748456] [drm] Initialized vdrm 1.0.0 20110917 on minor 0 [ 1.761398] loop: module loaded [ 1.764921] vmemexp device MAJOR num = 245 [ 1.769068] vmemexp class registered [ 1.772788] /dev/vmemexp device registered [ 1.776922] ioctl DBUFIOC_EXPORT_VIRTMEM = -1072899120 [ 1.782796] nand: No NAND device found [ 1.786567] omap2-nand 8000000.nand: scan failed, may be bus-width mismatch [ 1.796524] m25p80 spi32766.0: s25fl256s1 (32768 Kbytes) [ 1.801943] 7 ofpart partitions found on MTD device spi32766.0 [ 1.807820] Creating 7 MTD partitions on "spi32766.0": [ 1.812984] 0x000000000000-0x000000040000 : "QSPI.SPL" [ 1.819097] 0x000000040000-0x000000140000 : "QSPI.u-boot" [ 1.825425] 0x000000140000-0x0000001c0000 : "QSPI.u-boot-spl-os" [ 1.832378] 0x0000001c0000-0x0000001d0000 : "QSPI.u-boot-env" [ 1.839084] 0x0000001d0000-0x0000001e0000 : "QSPI.u-boot-env.backup1" [ 1.846468] 0x0000001e0000-0x0000009e0000 : "QSPI.kernel" [ 1.852820] 0x0000009e0000-0x000002000000 : "QSPI.file-system" [ 1.860641] libphy: Fixed MDIO Bus: probed [ 1.916616] davinci_mdio 48485000.mdio: davinci mdio revision 1.6 [ 1.922740] davinci_mdio 48485000.mdio: detected phy mask fffffff3 [ 1.933323] libphy: 48485000.mdio: probed [ 1.937373] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver unknown [ 1.945412] davinci_mdio 48485000.mdio: phy[3]: device 48485000.mdio:03, driver unknown [ 1.954101] cpsw 48484000.ethernet: Detected MACID = f0:b5:d1:1b:98:86 [ 1.960765] cpsw 48484000.ethernet: cpts: overflow check period 800 [ 1.967739] cpsw 48484000.ethernet: cpsw: Detected MACID = f0:b5:d1:1b:98:87 [ 1.976364] mousedev: PS/2 mouse device common for all mice [ 1.982571] i2c /dev entries driver [ 1.991323] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 1.996950] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr25 mode [ 2.003335] omap_hsmmc 480b4000.mmc: no pinctrl state for sdr12 mode [ 2.009889] evm_3v3_sw: supplied by sysen1 [ 2.090362] mmc0: MAN_BKOPS_EN bit is not set [ 2.102344] mmc0: new HS200 MMC card at address 0001 [ 2.117838] mmcblk0: mmc0:0001 MMC08G 7.25 GiB [ 2.132638] mmcblk0boot0: mmc0:0001 MMC08G partition 1 8.00 MiB [ 2.138818] mmcblk0boot1: mmc0:0001 MMC08G partition 2 8.00 MiB [ 2.168413] ledtrig-cpu: registered to indicate activity on CPUs [ 2.176915] aic_dvdd: supplied by evm_3v3_sw [ 2.182812] davinci-mcasp 4847c000.mcasp: invalid tdm slots: 0 [ 2.190302] NET: Registered protocol family 10 [ 2.205549] sit: IPv6 over IPv4 tunneling driver [ 2.210765] NET: Registered protocol family 17 [ 2.215446] Key type dns_resolver registered [ 2.219888] omap_voltage_late_init: Voltage driver support not added [ 2.226789] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.232998] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.239753] Adding alias for supply vdd,cpu0 -> vdd,4a003b20.oppdm [ 2.245960] Adding alias for supply vbb,cpu0 -> vbb,4a003b20.oppdm [ 2.254158] Power Management for TI OMAP4+ devices. [ 2.259243] Registering SWP/SWPB emulation handler [ 2.264982] dmm 4e000000.dmm: workaround for errata i878 in use [ 2.272237] dmm 4e000000.dmm: initialized all PAT entries [ 2.278356] [drm] Initialized omapdrm 1.0.0 20110917 on minor 1 [ 2.295040] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.301236] asoc-simple-card sound0: tlv320aic3x-hifi <-> 48468000.mcasp mapping ok [ 2.320817] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.326525] input: gpio_keys as /devices/platform/gpio_keys/input/input0 [ 2.333443] hctosys: unable to open rtc device (rtc0) [ 2.334038] omap_hsmmc 4809c000.mmc: Got CD GPIO [ 2.351380] evm_1v8: disabling [ 2.354451] aic_dvdd: disabling [ 2.357626] vmmcwl_fixed: disabling [ 2.361301] ldousb: disabling [ 2.364556] pbias_mmc_omap5: disabling [ 2.368479] ALSA device list: [ 2.371455] #0: DRA7xx-EVM [ 2.375004] Waiting for root device PARTUUID=f724ed05-02... |