module_content
stringlengths 18
1.05M
|
|---|
module read_netlist_v8_2 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_2 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_2 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_2 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule |
module blk_mem_axi_write_wrapper_beh_v8_2
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_2 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule |
module blk_mem_axi_read_wrapper_beh_v8_2
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_2
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule |
module blk_mem_axi_regs_fwd_v8_2
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule |
module BLK_MEM_GEN_v8_2_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule |
module BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule |
module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule |
module blk_mem_gen_v8_2
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = ""
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_2
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule |
module STATE_LOGIC_v8_2 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule |
module beh_vlog_muxf7_v8_2 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule |
module beh_vlog_ff_clr_v8_2 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule |
module beh_vlog_ff_pre_v8_2 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule |
module beh_vlog_ff_ce_clr_v8_2 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule |
module write_netlist_v8_2
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule |
module read_netlist_v8_2 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_2 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_2 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_2 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule |
module blk_mem_axi_write_wrapper_beh_v8_2
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_2 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule |
module blk_mem_axi_read_wrapper_beh_v8_2
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_2
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule |
module blk_mem_axi_regs_fwd_v8_2
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule |
module BLK_MEM_GEN_v8_2_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule |
module BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule |
module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule |
module blk_mem_gen_v8_2
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = ""
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_2
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule |
module sign_extend (in,out);
parameter bits_in=0; // FIXME Quartus insists on a default
parameter bits_out=0;
input [bits_in-1:0] in;
output [bits_out-1:0] out;
assign out = {{(bits_out-bits_in){in[bits_in-1]}},in};
endmodule |
module sign_extend (in,out);
parameter bits_in=0; // FIXME Quartus insists on a default
parameter bits_out=0;
input [bits_in-1:0] in;
output [bits_out-1:0] out;
assign out = {{(bits_out-bits_in){in[bits_in-1]}},in};
endmodule |
module testbed_lo_simulate;
reg pck0;
reg [7:0] adc_d;
wire pwr_lo;
wire adc_clk;
wire ck_1356meg;
wire ck_1356megb;
wire ssp_frame;
wire ssp_din;
wire ssp_clk;
reg ssp_dout;
wire pwr_hi;
wire pwr_oe1;
wire pwr_oe2;
wire pwr_oe3;
wire pwr_oe4;
reg cross_lo;
wire cross_hi;
wire dbg;
lo_simulate #(5,200) dut(
.pck0(pck0),
.ck_1356meg(ck_1356meg),
.ck_1356megb(ck_1356megb),
.pwr_lo(pwr_lo),
.pwr_hi(pwr_hi),
.pwr_oe1(pwr_oe1),
.pwr_oe2(pwr_oe2),
.pwr_oe3(pwr_oe3),
.pwr_oe4(pwr_oe4),
.adc_d(adc_d),
.adc_clk(adc_clk),
.ssp_frame(ssp_frame),
.ssp_din(ssp_din),
.ssp_dout(ssp_dout),
.ssp_clk(ssp_clk),
.cross_hi(cross_hi),
.cross_lo(cross_lo),
.dbg(dbg)
);
integer i, counter=0;
// main clock
always #5 pck0 = !pck0;
//cross_lo is not really synced to pck0 but it's roughly pck0/192 (24Mhz/192=125Khz)
task crank_dut;
begin
@(posedge pck0) ;
counter = counter + 1;
if (counter == 192) begin
counter = 0;
ssp_dout = $random;
cross_lo = 1;
end else begin
cross_lo = 0;
end
end
endtask
initial begin
pck0 = 0;
for (i = 0 ; i < 4096 ; i = i + 1) begin
crank_dut;
end
$finish;
end
endmodule |
module testbed_lo_simulate;
reg pck0;
reg [7:0] adc_d;
wire pwr_lo;
wire adc_clk;
wire ck_1356meg;
wire ck_1356megb;
wire ssp_frame;
wire ssp_din;
wire ssp_clk;
reg ssp_dout;
wire pwr_hi;
wire pwr_oe1;
wire pwr_oe2;
wire pwr_oe3;
wire pwr_oe4;
reg cross_lo;
wire cross_hi;
wire dbg;
lo_simulate #(5,200) dut(
.pck0(pck0),
.ck_1356meg(ck_1356meg),
.ck_1356megb(ck_1356megb),
.pwr_lo(pwr_lo),
.pwr_hi(pwr_hi),
.pwr_oe1(pwr_oe1),
.pwr_oe2(pwr_oe2),
.pwr_oe3(pwr_oe3),
.pwr_oe4(pwr_oe4),
.adc_d(adc_d),
.adc_clk(adc_clk),
.ssp_frame(ssp_frame),
.ssp_din(ssp_din),
.ssp_dout(ssp_dout),
.ssp_clk(ssp_clk),
.cross_hi(cross_hi),
.cross_lo(cross_lo),
.dbg(dbg)
);
integer i, counter=0;
// main clock
always #5 pck0 = !pck0;
//cross_lo is not really synced to pck0 but it's roughly pck0/192 (24Mhz/192=125Khz)
task crank_dut;
begin
@(posedge pck0) ;
counter = counter + 1;
if (counter == 192) begin
counter = 0;
ssp_dout = $random;
cross_lo = 1;
end else begin
cross_lo = 0;
end
end
endtask
initial begin
pck0 = 0;
for (i = 0 ; i < 4096 ; i = i + 1) begin
crank_dut;
end
$finish;
end
endmodule |
module testbed_lo_simulate;
reg pck0;
reg [7:0] adc_d;
wire pwr_lo;
wire adc_clk;
wire ck_1356meg;
wire ck_1356megb;
wire ssp_frame;
wire ssp_din;
wire ssp_clk;
reg ssp_dout;
wire pwr_hi;
wire pwr_oe1;
wire pwr_oe2;
wire pwr_oe3;
wire pwr_oe4;
reg cross_lo;
wire cross_hi;
wire dbg;
lo_simulate #(5,200) dut(
.pck0(pck0),
.ck_1356meg(ck_1356meg),
.ck_1356megb(ck_1356megb),
.pwr_lo(pwr_lo),
.pwr_hi(pwr_hi),
.pwr_oe1(pwr_oe1),
.pwr_oe2(pwr_oe2),
.pwr_oe3(pwr_oe3),
.pwr_oe4(pwr_oe4),
.adc_d(adc_d),
.adc_clk(adc_clk),
.ssp_frame(ssp_frame),
.ssp_din(ssp_din),
.ssp_dout(ssp_dout),
.ssp_clk(ssp_clk),
.cross_hi(cross_hi),
.cross_lo(cross_lo),
.dbg(dbg)
);
integer i, counter=0;
// main clock
always #5 pck0 = !pck0;
//cross_lo is not really synced to pck0 but it's roughly pck0/192 (24Mhz/192=125Khz)
task crank_dut;
begin
@(posedge pck0) ;
counter = counter + 1;
if (counter == 192) begin
counter = 0;
ssp_dout = $random;
cross_lo = 1;
end else begin
cross_lo = 0;
end
end
endtask
initial begin
pck0 = 0;
for (i = 0 ; i < 4096 ; i = i + 1) begin
crank_dut;
end
$finish;
end
endmodule |
module soc_design_Sys_Timer (
// inputs:
address,
chipselect,
clk,
reset_n,
write_n,
writedata,
// outputs:
irq,
readdata
)
;
output irq;
output [ 15: 0] readdata;
input [ 2: 0] address;
input chipselect;
input clk;
input reset_n;
input write_n;
input [ 15: 0] writedata;
wire clk_en;
wire control_interrupt_enable;
reg control_register;
wire control_wr_strobe;
reg counter_is_running;
wire counter_is_zero;
wire [ 16: 0] counter_load_value;
reg delayed_unxcounter_is_zeroxx0;
wire do_start_counter;
wire do_stop_counter;
reg force_reload;
reg [ 16: 0] internal_counter;
wire irq;
wire period_h_wr_strobe;
wire period_l_wr_strobe;
wire [ 15: 0] read_mux_out;
reg [ 15: 0] readdata;
wire status_wr_strobe;
wire timeout_event;
reg timeout_occurred;
assign clk_en = 1;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
internal_counter <= 17'h1869F;
else if (counter_is_running || force_reload)
if (counter_is_zero || force_reload)
internal_counter <= counter_load_value;
else
internal_counter <= internal_counter - 1;
end
assign counter_is_zero = internal_counter == 0;
assign counter_load_value = 17'h1869F;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
force_reload <= 0;
else if (clk_en)
force_reload <= period_h_wr_strobe || period_l_wr_strobe;
end
assign do_start_counter = 1;
assign do_stop_counter = 0;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
counter_is_running <= 1'b0;
else if (clk_en)
if (do_start_counter)
counter_is_running <= -1;
else if (do_stop_counter)
counter_is_running <= 0;
end
//delayed_unxcounter_is_zeroxx0, which is an e_register
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
delayed_unxcounter_is_zeroxx0 <= 0;
else if (clk_en)
delayed_unxcounter_is_zeroxx0 <= counter_is_zero;
end
assign timeout_event = (counter_is_zero) & ~(delayed_unxcounter_is_zeroxx0);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
timeout_occurred <= 0;
else if (clk_en)
if (status_wr_strobe)
timeout_occurred <= 0;
else if (timeout_event)
timeout_occurred <= -1;
end
assign irq = timeout_occurred && control_interrupt_enable;
//s1, which is an e_avalon_slave
assign read_mux_out = ({16 {(address == 1)}} & control_register) |
({16 {(address == 0)}} & {counter_is_running,
timeout_occurred});
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
readdata <= 0;
else if (clk_en)
readdata <= read_mux_out;
end
assign period_l_wr_strobe = chipselect && ~write_n && (address == 2);
assign period_h_wr_strobe = chipselect && ~write_n && (address == 3);
assign control_wr_strobe = chipselect && ~write_n && (address == 1);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
control_register <= 0;
else if (control_wr_strobe)
control_register <= writedata[0];
end
assign control_interrupt_enable = control_register;
assign status_wr_strobe = chipselect && ~write_n && (address == 0);
endmodule |
module soc_design_Sys_Timer (
// inputs:
address,
chipselect,
clk,
reset_n,
write_n,
writedata,
// outputs:
irq,
readdata
)
;
output irq;
output [ 15: 0] readdata;
input [ 2: 0] address;
input chipselect;
input clk;
input reset_n;
input write_n;
input [ 15: 0] writedata;
wire clk_en;
wire control_interrupt_enable;
reg control_register;
wire control_wr_strobe;
reg counter_is_running;
wire counter_is_zero;
wire [ 16: 0] counter_load_value;
reg delayed_unxcounter_is_zeroxx0;
wire do_start_counter;
wire do_stop_counter;
reg force_reload;
reg [ 16: 0] internal_counter;
wire irq;
wire period_h_wr_strobe;
wire period_l_wr_strobe;
wire [ 15: 0] read_mux_out;
reg [ 15: 0] readdata;
wire status_wr_strobe;
wire timeout_event;
reg timeout_occurred;
assign clk_en = 1;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
internal_counter <= 17'h1869F;
else if (counter_is_running || force_reload)
if (counter_is_zero || force_reload)
internal_counter <= counter_load_value;
else
internal_counter <= internal_counter - 1;
end
assign counter_is_zero = internal_counter == 0;
assign counter_load_value = 17'h1869F;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
force_reload <= 0;
else if (clk_en)
force_reload <= period_h_wr_strobe || period_l_wr_strobe;
end
assign do_start_counter = 1;
assign do_stop_counter = 0;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
counter_is_running <= 1'b0;
else if (clk_en)
if (do_start_counter)
counter_is_running <= -1;
else if (do_stop_counter)
counter_is_running <= 0;
end
//delayed_unxcounter_is_zeroxx0, which is an e_register
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
delayed_unxcounter_is_zeroxx0 <= 0;
else if (clk_en)
delayed_unxcounter_is_zeroxx0 <= counter_is_zero;
end
assign timeout_event = (counter_is_zero) & ~(delayed_unxcounter_is_zeroxx0);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
timeout_occurred <= 0;
else if (clk_en)
if (status_wr_strobe)
timeout_occurred <= 0;
else if (timeout_event)
timeout_occurred <= -1;
end
assign irq = timeout_occurred && control_interrupt_enable;
//s1, which is an e_avalon_slave
assign read_mux_out = ({16 {(address == 1)}} & control_register) |
({16 {(address == 0)}} & {counter_is_running,
timeout_occurred});
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
readdata <= 0;
else if (clk_en)
readdata <= read_mux_out;
end
assign period_l_wr_strobe = chipselect && ~write_n && (address == 2);
assign period_h_wr_strobe = chipselect && ~write_n && (address == 3);
assign control_wr_strobe = chipselect && ~write_n && (address == 1);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
control_register <= 0;
else if (control_wr_strobe)
control_register <= writedata[0];
end
assign control_interrupt_enable = control_register;
assign status_wr_strobe = chipselect && ~write_n && (address == 0);
endmodule |
module soc_design_Sys_Timer (
// inputs:
address,
chipselect,
clk,
reset_n,
write_n,
writedata,
// outputs:
irq,
readdata
)
;
output irq;
output [ 15: 0] readdata;
input [ 2: 0] address;
input chipselect;
input clk;
input reset_n;
input write_n;
input [ 15: 0] writedata;
wire clk_en;
wire control_interrupt_enable;
reg control_register;
wire control_wr_strobe;
reg counter_is_running;
wire counter_is_zero;
wire [ 16: 0] counter_load_value;
reg delayed_unxcounter_is_zeroxx0;
wire do_start_counter;
wire do_stop_counter;
reg force_reload;
reg [ 16: 0] internal_counter;
wire irq;
wire period_h_wr_strobe;
wire period_l_wr_strobe;
wire [ 15: 0] read_mux_out;
reg [ 15: 0] readdata;
wire status_wr_strobe;
wire timeout_event;
reg timeout_occurred;
assign clk_en = 1;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
internal_counter <= 17'h1869F;
else if (counter_is_running || force_reload)
if (counter_is_zero || force_reload)
internal_counter <= counter_load_value;
else
internal_counter <= internal_counter - 1;
end
assign counter_is_zero = internal_counter == 0;
assign counter_load_value = 17'h1869F;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
force_reload <= 0;
else if (clk_en)
force_reload <= period_h_wr_strobe || period_l_wr_strobe;
end
assign do_start_counter = 1;
assign do_stop_counter = 0;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
counter_is_running <= 1'b0;
else if (clk_en)
if (do_start_counter)
counter_is_running <= -1;
else if (do_stop_counter)
counter_is_running <= 0;
end
//delayed_unxcounter_is_zeroxx0, which is an e_register
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
delayed_unxcounter_is_zeroxx0 <= 0;
else if (clk_en)
delayed_unxcounter_is_zeroxx0 <= counter_is_zero;
end
assign timeout_event = (counter_is_zero) & ~(delayed_unxcounter_is_zeroxx0);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
timeout_occurred <= 0;
else if (clk_en)
if (status_wr_strobe)
timeout_occurred <= 0;
else if (timeout_event)
timeout_occurred <= -1;
end
assign irq = timeout_occurred && control_interrupt_enable;
//s1, which is an e_avalon_slave
assign read_mux_out = ({16 {(address == 1)}} & control_register) |
({16 {(address == 0)}} & {counter_is_running,
timeout_occurred});
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
readdata <= 0;
else if (clk_en)
readdata <= read_mux_out;
end
assign period_l_wr_strobe = chipselect && ~write_n && (address == 2);
assign period_h_wr_strobe = chipselect && ~write_n && (address == 3);
assign control_wr_strobe = chipselect && ~write_n && (address == 1);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
control_register <= 0;
else if (control_wr_strobe)
control_register <= writedata[0];
end
assign control_interrupt_enable = control_register;
assign status_wr_strobe = chipselect && ~write_n && (address == 0);
endmodule |
module soc_design_Sys_Timer (
// inputs:
address,
chipselect,
clk,
reset_n,
write_n,
writedata,
// outputs:
irq,
readdata
)
;
output irq;
output [ 15: 0] readdata;
input [ 2: 0] address;
input chipselect;
input clk;
input reset_n;
input write_n;
input [ 15: 0] writedata;
wire clk_en;
wire control_interrupt_enable;
reg control_register;
wire control_wr_strobe;
reg counter_is_running;
wire counter_is_zero;
wire [ 16: 0] counter_load_value;
reg delayed_unxcounter_is_zeroxx0;
wire do_start_counter;
wire do_stop_counter;
reg force_reload;
reg [ 16: 0] internal_counter;
wire irq;
wire period_h_wr_strobe;
wire period_l_wr_strobe;
wire [ 15: 0] read_mux_out;
reg [ 15: 0] readdata;
wire status_wr_strobe;
wire timeout_event;
reg timeout_occurred;
assign clk_en = 1;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
internal_counter <= 17'h1869F;
else if (counter_is_running || force_reload)
if (counter_is_zero || force_reload)
internal_counter <= counter_load_value;
else
internal_counter <= internal_counter - 1;
end
assign counter_is_zero = internal_counter == 0;
assign counter_load_value = 17'h1869F;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
force_reload <= 0;
else if (clk_en)
force_reload <= period_h_wr_strobe || period_l_wr_strobe;
end
assign do_start_counter = 1;
assign do_stop_counter = 0;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
counter_is_running <= 1'b0;
else if (clk_en)
if (do_start_counter)
counter_is_running <= -1;
else if (do_stop_counter)
counter_is_running <= 0;
end
//delayed_unxcounter_is_zeroxx0, which is an e_register
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
delayed_unxcounter_is_zeroxx0 <= 0;
else if (clk_en)
delayed_unxcounter_is_zeroxx0 <= counter_is_zero;
end
assign timeout_event = (counter_is_zero) & ~(delayed_unxcounter_is_zeroxx0);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
timeout_occurred <= 0;
else if (clk_en)
if (status_wr_strobe)
timeout_occurred <= 0;
else if (timeout_event)
timeout_occurred <= -1;
end
assign irq = timeout_occurred && control_interrupt_enable;
//s1, which is an e_avalon_slave
assign read_mux_out = ({16 {(address == 1)}} & control_register) |
({16 {(address == 0)}} & {counter_is_running,
timeout_occurred});
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
readdata <= 0;
else if (clk_en)
readdata <= read_mux_out;
end
assign period_l_wr_strobe = chipselect && ~write_n && (address == 2);
assign period_h_wr_strobe = chipselect && ~write_n && (address == 3);
assign control_wr_strobe = chipselect && ~write_n && (address == 1);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
control_register <= 0;
else if (control_wr_strobe)
control_register <= writedata[0];
end
assign control_interrupt_enable = control_register;
assign status_wr_strobe = chipselect && ~write_n && (address == 0);
endmodule |
module axi_protocol_converter_v2_1_axilite_conv #
(
parameter C_FAMILY = "virtex6",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1
)
(
// System Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [3-1:0] S_AXI_AWPROT,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER, // Constant =0
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [3-1:0] S_AXI_ARPROT,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST, // Constant =1
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER, // Constant =0
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [3-1:0] M_AXI_AWPROT,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [2-1:0] M_AXI_BRESP,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [3-1:0] M_AXI_ARPROT,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY
);
wire s_awvalid_i;
wire s_arvalid_i;
wire [C_AXI_ADDR_WIDTH-1:0] m_axaddr;
// Arbiter
reg read_active;
reg write_active;
reg busy;
wire read_req;
wire write_req;
wire read_complete;
wire write_complete;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ~ARESETN};
end
assign s_awvalid_i = S_AXI_AWVALID & (C_AXI_SUPPORTS_WRITE != 0);
assign s_arvalid_i = S_AXI_ARVALID & (C_AXI_SUPPORTS_READ != 0);
assign read_req = s_arvalid_i & ~busy & ~|areset_d & ~write_active;
assign write_req = s_awvalid_i & ~busy & ~|areset_d & ((~read_active & ~s_arvalid_i) | write_active);
assign read_complete = M_AXI_RVALID & S_AXI_RREADY;
assign write_complete = M_AXI_BVALID & S_AXI_BREADY;
always @(posedge ACLK) begin : arbiter_read_ff
if (|areset_d)
read_active <= 1'b0;
else if (read_complete)
read_active <= 1'b0;
else if (read_req)
read_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_write_ff
if (|areset_d)
write_active <= 1'b0;
else if (write_complete)
write_active <= 1'b0;
else if (write_req)
write_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_busy_ff
if (|areset_d)
busy <= 1'b0;
else if (read_complete | write_complete)
busy <= 1'b0;
else if ((write_req & M_AXI_AWREADY) | (read_req & M_AXI_ARREADY))
busy <= 1'b1;
end
assign M_AXI_ARVALID = read_req;
assign S_AXI_ARREADY = M_AXI_ARREADY & read_req;
assign M_AXI_AWVALID = write_req;
assign S_AXI_AWREADY = M_AXI_AWREADY & write_req;
assign M_AXI_RREADY = S_AXI_RREADY & read_active;
assign S_AXI_RVALID = M_AXI_RVALID & read_active;
assign M_AXI_BREADY = S_AXI_BREADY & write_active;
assign S_AXI_BVALID = M_AXI_BVALID & write_active;
// Address multiplexer
assign m_axaddr = (read_req | (C_AXI_SUPPORTS_WRITE == 0)) ? S_AXI_ARADDR : S_AXI_AWADDR;
// Id multiplexer and flip-flop
reg [C_AXI_ID_WIDTH-1:0] s_axid;
always @(posedge ACLK) begin : axid
if (read_req) s_axid <= S_AXI_ARID;
else if (write_req) s_axid <= S_AXI_AWID;
end
assign S_AXI_BID = s_axid;
assign S_AXI_RID = s_axid;
assign M_AXI_AWADDR = m_axaddr;
assign M_AXI_ARADDR = m_axaddr;
// Feed-through signals
assign S_AXI_WREADY = M_AXI_WREADY & ~|areset_d;
assign S_AXI_BRESP = M_AXI_BRESP;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = 1'b1;
assign S_AXI_BUSER = {C_AXI_BUSER_WIDTH{1'b0}};
assign S_AXI_RUSER = {C_AXI_RUSER_WIDTH{1'b0}};
assign M_AXI_AWPROT = S_AXI_AWPROT;
assign M_AXI_WVALID = S_AXI_WVALID & ~|areset_d;
assign M_AXI_WDATA = S_AXI_WDATA;
assign M_AXI_WSTRB = S_AXI_WSTRB;
assign M_AXI_ARPROT = S_AXI_ARPROT;
endmodule |
module axi_protocol_converter_v2_1_axilite_conv #
(
parameter C_FAMILY = "virtex6",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1
)
(
// System Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [3-1:0] S_AXI_AWPROT,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER, // Constant =0
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [3-1:0] S_AXI_ARPROT,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST, // Constant =1
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER, // Constant =0
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [3-1:0] M_AXI_AWPROT,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [2-1:0] M_AXI_BRESP,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [3-1:0] M_AXI_ARPROT,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY
);
wire s_awvalid_i;
wire s_arvalid_i;
wire [C_AXI_ADDR_WIDTH-1:0] m_axaddr;
// Arbiter
reg read_active;
reg write_active;
reg busy;
wire read_req;
wire write_req;
wire read_complete;
wire write_complete;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ~ARESETN};
end
assign s_awvalid_i = S_AXI_AWVALID & (C_AXI_SUPPORTS_WRITE != 0);
assign s_arvalid_i = S_AXI_ARVALID & (C_AXI_SUPPORTS_READ != 0);
assign read_req = s_arvalid_i & ~busy & ~|areset_d & ~write_active;
assign write_req = s_awvalid_i & ~busy & ~|areset_d & ((~read_active & ~s_arvalid_i) | write_active);
assign read_complete = M_AXI_RVALID & S_AXI_RREADY;
assign write_complete = M_AXI_BVALID & S_AXI_BREADY;
always @(posedge ACLK) begin : arbiter_read_ff
if (|areset_d)
read_active <= 1'b0;
else if (read_complete)
read_active <= 1'b0;
else if (read_req)
read_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_write_ff
if (|areset_d)
write_active <= 1'b0;
else if (write_complete)
write_active <= 1'b0;
else if (write_req)
write_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_busy_ff
if (|areset_d)
busy <= 1'b0;
else if (read_complete | write_complete)
busy <= 1'b0;
else if ((write_req & M_AXI_AWREADY) | (read_req & M_AXI_ARREADY))
busy <= 1'b1;
end
assign M_AXI_ARVALID = read_req;
assign S_AXI_ARREADY = M_AXI_ARREADY & read_req;
assign M_AXI_AWVALID = write_req;
assign S_AXI_AWREADY = M_AXI_AWREADY & write_req;
assign M_AXI_RREADY = S_AXI_RREADY & read_active;
assign S_AXI_RVALID = M_AXI_RVALID & read_active;
assign M_AXI_BREADY = S_AXI_BREADY & write_active;
assign S_AXI_BVALID = M_AXI_BVALID & write_active;
// Address multiplexer
assign m_axaddr = (read_req | (C_AXI_SUPPORTS_WRITE == 0)) ? S_AXI_ARADDR : S_AXI_AWADDR;
// Id multiplexer and flip-flop
reg [C_AXI_ID_WIDTH-1:0] s_axid;
always @(posedge ACLK) begin : axid
if (read_req) s_axid <= S_AXI_ARID;
else if (write_req) s_axid <= S_AXI_AWID;
end
assign S_AXI_BID = s_axid;
assign S_AXI_RID = s_axid;
assign M_AXI_AWADDR = m_axaddr;
assign M_AXI_ARADDR = m_axaddr;
// Feed-through signals
assign S_AXI_WREADY = M_AXI_WREADY & ~|areset_d;
assign S_AXI_BRESP = M_AXI_BRESP;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = 1'b1;
assign S_AXI_BUSER = {C_AXI_BUSER_WIDTH{1'b0}};
assign S_AXI_RUSER = {C_AXI_RUSER_WIDTH{1'b0}};
assign M_AXI_AWPROT = S_AXI_AWPROT;
assign M_AXI_WVALID = S_AXI_WVALID & ~|areset_d;
assign M_AXI_WDATA = S_AXI_WDATA;
assign M_AXI_WSTRB = S_AXI_WSTRB;
assign M_AXI_ARPROT = S_AXI_ARPROT;
endmodule |
module axi_protocol_converter_v2_1_axilite_conv #
(
parameter C_FAMILY = "virtex6",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1
)
(
// System Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [3-1:0] S_AXI_AWPROT,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER, // Constant =0
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [3-1:0] S_AXI_ARPROT,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST, // Constant =1
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER, // Constant =0
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [3-1:0] M_AXI_AWPROT,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [2-1:0] M_AXI_BRESP,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [3-1:0] M_AXI_ARPROT,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY
);
wire s_awvalid_i;
wire s_arvalid_i;
wire [C_AXI_ADDR_WIDTH-1:0] m_axaddr;
// Arbiter
reg read_active;
reg write_active;
reg busy;
wire read_req;
wire write_req;
wire read_complete;
wire write_complete;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ~ARESETN};
end
assign s_awvalid_i = S_AXI_AWVALID & (C_AXI_SUPPORTS_WRITE != 0);
assign s_arvalid_i = S_AXI_ARVALID & (C_AXI_SUPPORTS_READ != 0);
assign read_req = s_arvalid_i & ~busy & ~|areset_d & ~write_active;
assign write_req = s_awvalid_i & ~busy & ~|areset_d & ((~read_active & ~s_arvalid_i) | write_active);
assign read_complete = M_AXI_RVALID & S_AXI_RREADY;
assign write_complete = M_AXI_BVALID & S_AXI_BREADY;
always @(posedge ACLK) begin : arbiter_read_ff
if (|areset_d)
read_active <= 1'b0;
else if (read_complete)
read_active <= 1'b0;
else if (read_req)
read_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_write_ff
if (|areset_d)
write_active <= 1'b0;
else if (write_complete)
write_active <= 1'b0;
else if (write_req)
write_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_busy_ff
if (|areset_d)
busy <= 1'b0;
else if (read_complete | write_complete)
busy <= 1'b0;
else if ((write_req & M_AXI_AWREADY) | (read_req & M_AXI_ARREADY))
busy <= 1'b1;
end
assign M_AXI_ARVALID = read_req;
assign S_AXI_ARREADY = M_AXI_ARREADY & read_req;
assign M_AXI_AWVALID = write_req;
assign S_AXI_AWREADY = M_AXI_AWREADY & write_req;
assign M_AXI_RREADY = S_AXI_RREADY & read_active;
assign S_AXI_RVALID = M_AXI_RVALID & read_active;
assign M_AXI_BREADY = S_AXI_BREADY & write_active;
assign S_AXI_BVALID = M_AXI_BVALID & write_active;
// Address multiplexer
assign m_axaddr = (read_req | (C_AXI_SUPPORTS_WRITE == 0)) ? S_AXI_ARADDR : S_AXI_AWADDR;
// Id multiplexer and flip-flop
reg [C_AXI_ID_WIDTH-1:0] s_axid;
always @(posedge ACLK) begin : axid
if (read_req) s_axid <= S_AXI_ARID;
else if (write_req) s_axid <= S_AXI_AWID;
end
assign S_AXI_BID = s_axid;
assign S_AXI_RID = s_axid;
assign M_AXI_AWADDR = m_axaddr;
assign M_AXI_ARADDR = m_axaddr;
// Feed-through signals
assign S_AXI_WREADY = M_AXI_WREADY & ~|areset_d;
assign S_AXI_BRESP = M_AXI_BRESP;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = 1'b1;
assign S_AXI_BUSER = {C_AXI_BUSER_WIDTH{1'b0}};
assign S_AXI_RUSER = {C_AXI_RUSER_WIDTH{1'b0}};
assign M_AXI_AWPROT = S_AXI_AWPROT;
assign M_AXI_WVALID = S_AXI_WVALID & ~|areset_d;
assign M_AXI_WDATA = S_AXI_WDATA;
assign M_AXI_WSTRB = S_AXI_WSTRB;
assign M_AXI_ARPROT = S_AXI_ARPROT;
endmodule |
module axi_protocol_converter_v2_1_axilite_conv #
(
parameter C_FAMILY = "virtex6",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1
)
(
// System Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [3-1:0] S_AXI_AWPROT,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER, // Constant =0
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [3-1:0] S_AXI_ARPROT,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST, // Constant =1
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER, // Constant =0
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [3-1:0] M_AXI_AWPROT,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [2-1:0] M_AXI_BRESP,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [3-1:0] M_AXI_ARPROT,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY
);
wire s_awvalid_i;
wire s_arvalid_i;
wire [C_AXI_ADDR_WIDTH-1:0] m_axaddr;
// Arbiter
reg read_active;
reg write_active;
reg busy;
wire read_req;
wire write_req;
wire read_complete;
wire write_complete;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ~ARESETN};
end
assign s_awvalid_i = S_AXI_AWVALID & (C_AXI_SUPPORTS_WRITE != 0);
assign s_arvalid_i = S_AXI_ARVALID & (C_AXI_SUPPORTS_READ != 0);
assign read_req = s_arvalid_i & ~busy & ~|areset_d & ~write_active;
assign write_req = s_awvalid_i & ~busy & ~|areset_d & ((~read_active & ~s_arvalid_i) | write_active);
assign read_complete = M_AXI_RVALID & S_AXI_RREADY;
assign write_complete = M_AXI_BVALID & S_AXI_BREADY;
always @(posedge ACLK) begin : arbiter_read_ff
if (|areset_d)
read_active <= 1'b0;
else if (read_complete)
read_active <= 1'b0;
else if (read_req)
read_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_write_ff
if (|areset_d)
write_active <= 1'b0;
else if (write_complete)
write_active <= 1'b0;
else if (write_req)
write_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_busy_ff
if (|areset_d)
busy <= 1'b0;
else if (read_complete | write_complete)
busy <= 1'b0;
else if ((write_req & M_AXI_AWREADY) | (read_req & M_AXI_ARREADY))
busy <= 1'b1;
end
assign M_AXI_ARVALID = read_req;
assign S_AXI_ARREADY = M_AXI_ARREADY & read_req;
assign M_AXI_AWVALID = write_req;
assign S_AXI_AWREADY = M_AXI_AWREADY & write_req;
assign M_AXI_RREADY = S_AXI_RREADY & read_active;
assign S_AXI_RVALID = M_AXI_RVALID & read_active;
assign M_AXI_BREADY = S_AXI_BREADY & write_active;
assign S_AXI_BVALID = M_AXI_BVALID & write_active;
// Address multiplexer
assign m_axaddr = (read_req | (C_AXI_SUPPORTS_WRITE == 0)) ? S_AXI_ARADDR : S_AXI_AWADDR;
// Id multiplexer and flip-flop
reg [C_AXI_ID_WIDTH-1:0] s_axid;
always @(posedge ACLK) begin : axid
if (read_req) s_axid <= S_AXI_ARID;
else if (write_req) s_axid <= S_AXI_AWID;
end
assign S_AXI_BID = s_axid;
assign S_AXI_RID = s_axid;
assign M_AXI_AWADDR = m_axaddr;
assign M_AXI_ARADDR = m_axaddr;
// Feed-through signals
assign S_AXI_WREADY = M_AXI_WREADY & ~|areset_d;
assign S_AXI_BRESP = M_AXI_BRESP;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = 1'b1;
assign S_AXI_BUSER = {C_AXI_BUSER_WIDTH{1'b0}};
assign S_AXI_RUSER = {C_AXI_RUSER_WIDTH{1'b0}};
assign M_AXI_AWPROT = S_AXI_AWPROT;
assign M_AXI_WVALID = S_AXI_WVALID & ~|areset_d;
assign M_AXI_WDATA = S_AXI_WDATA;
assign M_AXI_WSTRB = S_AXI_WSTRB;
assign M_AXI_ARPROT = S_AXI_ARPROT;
endmodule |
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule |
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule |
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule |
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule |
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule |
module soc_design_niosII_core_cpu_mult_cell (
// inputs:
E_src1,
E_src2,
M_en,
clk,
reset_n,
// outputs:
M_mul_cell_p1,
M_mul_cell_p2,
M_mul_cell_p3
)
;
output [ 31: 0] M_mul_cell_p1;
output [ 31: 0] M_mul_cell_p2;
output [ 31: 0] M_mul_cell_p3;
input [ 31: 0] E_src1;
input [ 31: 0] E_src2;
input M_en;
input clk;
input reset_n;
wire [ 31: 0] M_mul_cell_p1;
wire [ 31: 0] M_mul_cell_p2;
wire [ 31: 0] M_mul_cell_p3;
wire mul_clr;
wire [ 31: 0] mul_src1;
wire [ 31: 0] mul_src2;
assign mul_clr = ~reset_n;
assign mul_src1 = E_src1;
assign mul_src2 = E_src2;
altera_mult_add the_altmult_add_p1
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p1)
);
defparam the_altmult_add_p1.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p1.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p1.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p1.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p1.input_register_a0 = "UNREGISTERED",
the_altmult_add_p1.input_register_b0 = "UNREGISTERED",
the_altmult_add_p1.input_source_a0 = "DATAA",
the_altmult_add_p1.input_source_b0 = "DATAB",
the_altmult_add_p1.lpm_type = "altera_mult_add",
the_altmult_add_p1.multiplier1_direction = "ADD",
the_altmult_add_p1.multiplier_aclr0 = "ACLR0",
the_altmult_add_p1.multiplier_register0 = "CLOCK0",
the_altmult_add_p1.number_of_multipliers = 1,
the_altmult_add_p1.output_register = "UNREGISTERED",
the_altmult_add_p1.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p1.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p1.representation_a = "UNSIGNED",
the_altmult_add_p1.representation_b = "UNSIGNED",
the_altmult_add_p1.selected_device_family = "CYCLONEV",
the_altmult_add_p1.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p1.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p1.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p1.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p1.signed_register_a = "UNREGISTERED",
the_altmult_add_p1.signed_register_b = "UNREGISTERED",
the_altmult_add_p1.width_a = 16,
the_altmult_add_p1.width_b = 16,
the_altmult_add_p1.width_result = 32;
altera_mult_add the_altmult_add_p2
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[31 : 16]),
.ena0 (M_en),
.result (M_mul_cell_p2)
);
defparam the_altmult_add_p2.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p2.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p2.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p2.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p2.input_register_a0 = "UNREGISTERED",
the_altmult_add_p2.input_register_b0 = "UNREGISTERED",
the_altmult_add_p2.input_source_a0 = "DATAA",
the_altmult_add_p2.input_source_b0 = "DATAB",
the_altmult_add_p2.lpm_type = "altera_mult_add",
the_altmult_add_p2.multiplier1_direction = "ADD",
the_altmult_add_p2.multiplier_aclr0 = "ACLR0",
the_altmult_add_p2.multiplier_register0 = "CLOCK0",
the_altmult_add_p2.number_of_multipliers = 1,
the_altmult_add_p2.output_register = "UNREGISTERED",
the_altmult_add_p2.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p2.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p2.representation_a = "UNSIGNED",
the_altmult_add_p2.representation_b = "UNSIGNED",
the_altmult_add_p2.selected_device_family = "CYCLONEV",
the_altmult_add_p2.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p2.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p2.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p2.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p2.signed_register_a = "UNREGISTERED",
the_altmult_add_p2.signed_register_b = "UNREGISTERED",
the_altmult_add_p2.width_a = 16,
the_altmult_add_p2.width_b = 16,
the_altmult_add_p2.width_result = 32;
altera_mult_add the_altmult_add_p3
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[31 : 16]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p3)
);
defparam the_altmult_add_p3.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p3.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p3.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p3.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p3.input_register_a0 = "UNREGISTERED",
the_altmult_add_p3.input_register_b0 = "UNREGISTERED",
the_altmult_add_p3.input_source_a0 = "DATAA",
the_altmult_add_p3.input_source_b0 = "DATAB",
the_altmult_add_p3.lpm_type = "altera_mult_add",
the_altmult_add_p3.multiplier1_direction = "ADD",
the_altmult_add_p3.multiplier_aclr0 = "ACLR0",
the_altmult_add_p3.multiplier_register0 = "CLOCK0",
the_altmult_add_p3.number_of_multipliers = 1,
the_altmult_add_p3.output_register = "UNREGISTERED",
the_altmult_add_p3.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p3.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p3.representation_a = "UNSIGNED",
the_altmult_add_p3.representation_b = "UNSIGNED",
the_altmult_add_p3.selected_device_family = "CYCLONEV",
the_altmult_add_p3.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p3.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p3.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p3.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p3.signed_register_a = "UNREGISTERED",
the_altmult_add_p3.signed_register_b = "UNREGISTERED",
the_altmult_add_p3.width_a = 16,
the_altmult_add_p3.width_b = 16,
the_altmult_add_p3.width_result = 32;
endmodule |
module soc_design_niosII_core_cpu_mult_cell (
// inputs:
E_src1,
E_src2,
M_en,
clk,
reset_n,
// outputs:
M_mul_cell_p1,
M_mul_cell_p2,
M_mul_cell_p3
)
;
output [ 31: 0] M_mul_cell_p1;
output [ 31: 0] M_mul_cell_p2;
output [ 31: 0] M_mul_cell_p3;
input [ 31: 0] E_src1;
input [ 31: 0] E_src2;
input M_en;
input clk;
input reset_n;
wire [ 31: 0] M_mul_cell_p1;
wire [ 31: 0] M_mul_cell_p2;
wire [ 31: 0] M_mul_cell_p3;
wire mul_clr;
wire [ 31: 0] mul_src1;
wire [ 31: 0] mul_src2;
assign mul_clr = ~reset_n;
assign mul_src1 = E_src1;
assign mul_src2 = E_src2;
altera_mult_add the_altmult_add_p1
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p1)
);
defparam the_altmult_add_p1.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p1.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p1.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p1.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p1.input_register_a0 = "UNREGISTERED",
the_altmult_add_p1.input_register_b0 = "UNREGISTERED",
the_altmult_add_p1.input_source_a0 = "DATAA",
the_altmult_add_p1.input_source_b0 = "DATAB",
the_altmult_add_p1.lpm_type = "altera_mult_add",
the_altmult_add_p1.multiplier1_direction = "ADD",
the_altmult_add_p1.multiplier_aclr0 = "ACLR0",
the_altmult_add_p1.multiplier_register0 = "CLOCK0",
the_altmult_add_p1.number_of_multipliers = 1,
the_altmult_add_p1.output_register = "UNREGISTERED",
the_altmult_add_p1.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p1.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p1.representation_a = "UNSIGNED",
the_altmult_add_p1.representation_b = "UNSIGNED",
the_altmult_add_p1.selected_device_family = "CYCLONEV",
the_altmult_add_p1.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p1.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p1.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p1.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p1.signed_register_a = "UNREGISTERED",
the_altmult_add_p1.signed_register_b = "UNREGISTERED",
the_altmult_add_p1.width_a = 16,
the_altmult_add_p1.width_b = 16,
the_altmult_add_p1.width_result = 32;
altera_mult_add the_altmult_add_p2
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[31 : 16]),
.ena0 (M_en),
.result (M_mul_cell_p2)
);
defparam the_altmult_add_p2.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p2.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p2.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p2.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p2.input_register_a0 = "UNREGISTERED",
the_altmult_add_p2.input_register_b0 = "UNREGISTERED",
the_altmult_add_p2.input_source_a0 = "DATAA",
the_altmult_add_p2.input_source_b0 = "DATAB",
the_altmult_add_p2.lpm_type = "altera_mult_add",
the_altmult_add_p2.multiplier1_direction = "ADD",
the_altmult_add_p2.multiplier_aclr0 = "ACLR0",
the_altmult_add_p2.multiplier_register0 = "CLOCK0",
the_altmult_add_p2.number_of_multipliers = 1,
the_altmult_add_p2.output_register = "UNREGISTERED",
the_altmult_add_p2.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p2.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p2.representation_a = "UNSIGNED",
the_altmult_add_p2.representation_b = "UNSIGNED",
the_altmult_add_p2.selected_device_family = "CYCLONEV",
the_altmult_add_p2.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p2.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p2.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p2.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p2.signed_register_a = "UNREGISTERED",
the_altmult_add_p2.signed_register_b = "UNREGISTERED",
the_altmult_add_p2.width_a = 16,
the_altmult_add_p2.width_b = 16,
the_altmult_add_p2.width_result = 32;
altera_mult_add the_altmult_add_p3
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[31 : 16]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p3)
);
defparam the_altmult_add_p3.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p3.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p3.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p3.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p3.input_register_a0 = "UNREGISTERED",
the_altmult_add_p3.input_register_b0 = "UNREGISTERED",
the_altmult_add_p3.input_source_a0 = "DATAA",
the_altmult_add_p3.input_source_b0 = "DATAB",
the_altmult_add_p3.lpm_type = "altera_mult_add",
the_altmult_add_p3.multiplier1_direction = "ADD",
the_altmult_add_p3.multiplier_aclr0 = "ACLR0",
the_altmult_add_p3.multiplier_register0 = "CLOCK0",
the_altmult_add_p3.number_of_multipliers = 1,
the_altmult_add_p3.output_register = "UNREGISTERED",
the_altmult_add_p3.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p3.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p3.representation_a = "UNSIGNED",
the_altmult_add_p3.representation_b = "UNSIGNED",
the_altmult_add_p3.selected_device_family = "CYCLONEV",
the_altmult_add_p3.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p3.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p3.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p3.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p3.signed_register_a = "UNREGISTERED",
the_altmult_add_p3.signed_register_b = "UNREGISTERED",
the_altmult_add_p3.width_a = 16,
the_altmult_add_p3.width_b = 16,
the_altmult_add_p3.width_result = 32;
endmodule |
module soc_design_niosII_core_cpu_mult_cell (
// inputs:
E_src1,
E_src2,
M_en,
clk,
reset_n,
// outputs:
M_mul_cell_p1,
M_mul_cell_p2,
M_mul_cell_p3
)
;
output [ 31: 0] M_mul_cell_p1;
output [ 31: 0] M_mul_cell_p2;
output [ 31: 0] M_mul_cell_p3;
input [ 31: 0] E_src1;
input [ 31: 0] E_src2;
input M_en;
input clk;
input reset_n;
wire [ 31: 0] M_mul_cell_p1;
wire [ 31: 0] M_mul_cell_p2;
wire [ 31: 0] M_mul_cell_p3;
wire mul_clr;
wire [ 31: 0] mul_src1;
wire [ 31: 0] mul_src2;
assign mul_clr = ~reset_n;
assign mul_src1 = E_src1;
assign mul_src2 = E_src2;
altera_mult_add the_altmult_add_p1
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p1)
);
defparam the_altmult_add_p1.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p1.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p1.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p1.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p1.input_register_a0 = "UNREGISTERED",
the_altmult_add_p1.input_register_b0 = "UNREGISTERED",
the_altmult_add_p1.input_source_a0 = "DATAA",
the_altmult_add_p1.input_source_b0 = "DATAB",
the_altmult_add_p1.lpm_type = "altera_mult_add",
the_altmult_add_p1.multiplier1_direction = "ADD",
the_altmult_add_p1.multiplier_aclr0 = "ACLR0",
the_altmult_add_p1.multiplier_register0 = "CLOCK0",
the_altmult_add_p1.number_of_multipliers = 1,
the_altmult_add_p1.output_register = "UNREGISTERED",
the_altmult_add_p1.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p1.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p1.representation_a = "UNSIGNED",
the_altmult_add_p1.representation_b = "UNSIGNED",
the_altmult_add_p1.selected_device_family = "CYCLONEV",
the_altmult_add_p1.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p1.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p1.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p1.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p1.signed_register_a = "UNREGISTERED",
the_altmult_add_p1.signed_register_b = "UNREGISTERED",
the_altmult_add_p1.width_a = 16,
the_altmult_add_p1.width_b = 16,
the_altmult_add_p1.width_result = 32;
altera_mult_add the_altmult_add_p2
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[31 : 16]),
.ena0 (M_en),
.result (M_mul_cell_p2)
);
defparam the_altmult_add_p2.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p2.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p2.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p2.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p2.input_register_a0 = "UNREGISTERED",
the_altmult_add_p2.input_register_b0 = "UNREGISTERED",
the_altmult_add_p2.input_source_a0 = "DATAA",
the_altmult_add_p2.input_source_b0 = "DATAB",
the_altmult_add_p2.lpm_type = "altera_mult_add",
the_altmult_add_p2.multiplier1_direction = "ADD",
the_altmult_add_p2.multiplier_aclr0 = "ACLR0",
the_altmult_add_p2.multiplier_register0 = "CLOCK0",
the_altmult_add_p2.number_of_multipliers = 1,
the_altmult_add_p2.output_register = "UNREGISTERED",
the_altmult_add_p2.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p2.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p2.representation_a = "UNSIGNED",
the_altmult_add_p2.representation_b = "UNSIGNED",
the_altmult_add_p2.selected_device_family = "CYCLONEV",
the_altmult_add_p2.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p2.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p2.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p2.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p2.signed_register_a = "UNREGISTERED",
the_altmult_add_p2.signed_register_b = "UNREGISTERED",
the_altmult_add_p2.width_a = 16,
the_altmult_add_p2.width_b = 16,
the_altmult_add_p2.width_result = 32;
altera_mult_add the_altmult_add_p3
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[31 : 16]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p3)
);
defparam the_altmult_add_p3.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p3.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p3.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p3.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p3.input_register_a0 = "UNREGISTERED",
the_altmult_add_p3.input_register_b0 = "UNREGISTERED",
the_altmult_add_p3.input_source_a0 = "DATAA",
the_altmult_add_p3.input_source_b0 = "DATAB",
the_altmult_add_p3.lpm_type = "altera_mult_add",
the_altmult_add_p3.multiplier1_direction = "ADD",
the_altmult_add_p3.multiplier_aclr0 = "ACLR0",
the_altmult_add_p3.multiplier_register0 = "CLOCK0",
the_altmult_add_p3.number_of_multipliers = 1,
the_altmult_add_p3.output_register = "UNREGISTERED",
the_altmult_add_p3.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p3.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p3.representation_a = "UNSIGNED",
the_altmult_add_p3.representation_b = "UNSIGNED",
the_altmult_add_p3.selected_device_family = "CYCLONEV",
the_altmult_add_p3.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p3.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p3.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p3.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p3.signed_register_a = "UNREGISTERED",
the_altmult_add_p3.signed_register_b = "UNREGISTERED",
the_altmult_add_p3.width_a = 16,
the_altmult_add_p3.width_b = 16,
the_altmult_add_p3.width_result = 32;
endmodule |
module soc_design_niosII_core_cpu_mult_cell (
// inputs:
E_src1,
E_src2,
M_en,
clk,
reset_n,
// outputs:
M_mul_cell_p1,
M_mul_cell_p2,
M_mul_cell_p3
)
;
output [ 31: 0] M_mul_cell_p1;
output [ 31: 0] M_mul_cell_p2;
output [ 31: 0] M_mul_cell_p3;
input [ 31: 0] E_src1;
input [ 31: 0] E_src2;
input M_en;
input clk;
input reset_n;
wire [ 31: 0] M_mul_cell_p1;
wire [ 31: 0] M_mul_cell_p2;
wire [ 31: 0] M_mul_cell_p3;
wire mul_clr;
wire [ 31: 0] mul_src1;
wire [ 31: 0] mul_src2;
assign mul_clr = ~reset_n;
assign mul_src1 = E_src1;
assign mul_src2 = E_src2;
altera_mult_add the_altmult_add_p1
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p1)
);
defparam the_altmult_add_p1.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p1.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p1.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p1.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p1.input_register_a0 = "UNREGISTERED",
the_altmult_add_p1.input_register_b0 = "UNREGISTERED",
the_altmult_add_p1.input_source_a0 = "DATAA",
the_altmult_add_p1.input_source_b0 = "DATAB",
the_altmult_add_p1.lpm_type = "altera_mult_add",
the_altmult_add_p1.multiplier1_direction = "ADD",
the_altmult_add_p1.multiplier_aclr0 = "ACLR0",
the_altmult_add_p1.multiplier_register0 = "CLOCK0",
the_altmult_add_p1.number_of_multipliers = 1,
the_altmult_add_p1.output_register = "UNREGISTERED",
the_altmult_add_p1.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p1.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p1.representation_a = "UNSIGNED",
the_altmult_add_p1.representation_b = "UNSIGNED",
the_altmult_add_p1.selected_device_family = "CYCLONEV",
the_altmult_add_p1.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p1.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p1.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p1.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p1.signed_register_a = "UNREGISTERED",
the_altmult_add_p1.signed_register_b = "UNREGISTERED",
the_altmult_add_p1.width_a = 16,
the_altmult_add_p1.width_b = 16,
the_altmult_add_p1.width_result = 32;
altera_mult_add the_altmult_add_p2
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[31 : 16]),
.ena0 (M_en),
.result (M_mul_cell_p2)
);
defparam the_altmult_add_p2.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p2.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p2.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p2.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p2.input_register_a0 = "UNREGISTERED",
the_altmult_add_p2.input_register_b0 = "UNREGISTERED",
the_altmult_add_p2.input_source_a0 = "DATAA",
the_altmult_add_p2.input_source_b0 = "DATAB",
the_altmult_add_p2.lpm_type = "altera_mult_add",
the_altmult_add_p2.multiplier1_direction = "ADD",
the_altmult_add_p2.multiplier_aclr0 = "ACLR0",
the_altmult_add_p2.multiplier_register0 = "CLOCK0",
the_altmult_add_p2.number_of_multipliers = 1,
the_altmult_add_p2.output_register = "UNREGISTERED",
the_altmult_add_p2.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p2.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p2.representation_a = "UNSIGNED",
the_altmult_add_p2.representation_b = "UNSIGNED",
the_altmult_add_p2.selected_device_family = "CYCLONEV",
the_altmult_add_p2.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p2.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p2.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p2.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p2.signed_register_a = "UNREGISTERED",
the_altmult_add_p2.signed_register_b = "UNREGISTERED",
the_altmult_add_p2.width_a = 16,
the_altmult_add_p2.width_b = 16,
the_altmult_add_p2.width_result = 32;
altera_mult_add the_altmult_add_p3
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[31 : 16]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p3)
);
defparam the_altmult_add_p3.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p3.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p3.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p3.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p3.input_register_a0 = "UNREGISTERED",
the_altmult_add_p3.input_register_b0 = "UNREGISTERED",
the_altmult_add_p3.input_source_a0 = "DATAA",
the_altmult_add_p3.input_source_b0 = "DATAB",
the_altmult_add_p3.lpm_type = "altera_mult_add",
the_altmult_add_p3.multiplier1_direction = "ADD",
the_altmult_add_p3.multiplier_aclr0 = "ACLR0",
the_altmult_add_p3.multiplier_register0 = "CLOCK0",
the_altmult_add_p3.number_of_multipliers = 1,
the_altmult_add_p3.output_register = "UNREGISTERED",
the_altmult_add_p3.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p3.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p3.representation_a = "UNSIGNED",
the_altmult_add_p3.representation_b = "UNSIGNED",
the_altmult_add_p3.selected_device_family = "CYCLONEV",
the_altmult_add_p3.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p3.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p3.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p3.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p3.signed_register_a = "UNREGISTERED",
the_altmult_add_p3.signed_register_b = "UNREGISTERED",
the_altmult_add_p3.width_a = 16,
the_altmult_add_p3.width_b = 16,
the_altmult_add_p3.width_result = 32;
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule |
module axi_infrastructure_v1_1_axic_srl_fifo #(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
parameter C_FAMILY = "virtex7",
parameter integer C_PAYLOAD_WIDTH = 1,
parameter integer C_FIFO_DEPTH = 16 // Range: 4-16.
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire aclk, // Clock
input wire aresetn, // Reset
input wire [C_PAYLOAD_WIDTH-1:0] s_payload, // Input data
input wire s_valid, // Input data valid
output reg s_ready, // Input data ready
output wire [C_PAYLOAD_WIDTH-1:0] m_payload, // Output data
output reg m_valid, // Output data valid
input wire m_ready // Output data ready
);
////////////////////////////////////////////////////////////////////////////////
// Functions
////////////////////////////////////////////////////////////////////////////////
// ceiling logb2
function integer f_clogb2 (input integer size);
integer s;
begin
s = size;
s = s - 1;
for (f_clogb2=1; s>1; f_clogb2=f_clogb2+1)
s = s >> 1;
end
endfunction // clogb2
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
localparam integer LP_LOG_FIFO_DEPTH = f_clogb2(C_FIFO_DEPTH);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [LP_LOG_FIFO_DEPTH-1:0] fifo_index;
wire [4-1:0] fifo_addr;
wire push;
wire pop ;
reg areset_r1;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
always @(posedge aclk) begin
areset_r1 <= ~aresetn;
end
always @(posedge aclk) begin
if (~aresetn) begin
fifo_index <= {LP_LOG_FIFO_DEPTH{1'b1}};
end
else begin
fifo_index <= push & ~pop ? fifo_index + 1'b1 :
~push & pop ? fifo_index - 1'b1 :
fifo_index;
end
end
assign push = s_valid & s_ready;
always @(posedge aclk) begin
if (~aresetn) begin
s_ready <= 1'b0;
end
else begin
s_ready <= areset_r1 ? 1'b1 :
push & ~pop && (fifo_index == (C_FIFO_DEPTH - 2'd2)) ? 1'b0 :
~push & pop ? 1'b1 :
s_ready;
end
end
assign pop = m_valid & m_ready;
always @(posedge aclk) begin
if (~aresetn) begin
m_valid <= 1'b0;
end
else begin
m_valid <= ~push & pop && (fifo_index == {LP_LOG_FIFO_DEPTH{1'b0}}) ? 1'b0 :
push & ~pop ? 1'b1 :
m_valid;
end
end
generate
if (LP_LOG_FIFO_DEPTH < 4) begin : gen_pad_fifo_addr
assign fifo_addr[0+:LP_LOG_FIFO_DEPTH] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
assign fifo_addr[LP_LOG_FIFO_DEPTH+:(4-LP_LOG_FIFO_DEPTH)] = {4-LP_LOG_FIFO_DEPTH{1'b0}};
end
else begin : gen_fifo_addr
assign fifo_addr[LP_LOG_FIFO_DEPTH-1:0] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
end
endgenerate
generate
genvar i;
for (i = 0; i < C_PAYLOAD_WIDTH; i = i + 1) begin : gen_data_bit
SRL16E
u_srl_fifo(
.Q ( m_payload[i] ) ,
.A0 ( fifo_addr[0] ) ,
.A1 ( fifo_addr[1] ) ,
.A2 ( fifo_addr[2] ) ,
.A3 ( fifo_addr[3] ) ,
.CE ( push ) ,
.CLK ( aclk ) ,
.D ( s_payload[i] )
);
end
endgenerate
endmodule |
module axi_infrastructure_v1_1_axic_srl_fifo #(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
parameter C_FAMILY = "virtex7",
parameter integer C_PAYLOAD_WIDTH = 1,
parameter integer C_FIFO_DEPTH = 16 // Range: 4-16.
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire aclk, // Clock
input wire aresetn, // Reset
input wire [C_PAYLOAD_WIDTH-1:0] s_payload, // Input data
input wire s_valid, // Input data valid
output reg s_ready, // Input data ready
output wire [C_PAYLOAD_WIDTH-1:0] m_payload, // Output data
output reg m_valid, // Output data valid
input wire m_ready // Output data ready
);
////////////////////////////////////////////////////////////////////////////////
// Functions
////////////////////////////////////////////////////////////////////////////////
// ceiling logb2
function integer f_clogb2 (input integer size);
integer s;
begin
s = size;
s = s - 1;
for (f_clogb2=1; s>1; f_clogb2=f_clogb2+1)
s = s >> 1;
end
endfunction // clogb2
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
localparam integer LP_LOG_FIFO_DEPTH = f_clogb2(C_FIFO_DEPTH);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [LP_LOG_FIFO_DEPTH-1:0] fifo_index;
wire [4-1:0] fifo_addr;
wire push;
wire pop ;
reg areset_r1;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
always @(posedge aclk) begin
areset_r1 <= ~aresetn;
end
always @(posedge aclk) begin
if (~aresetn) begin
fifo_index <= {LP_LOG_FIFO_DEPTH{1'b1}};
end
else begin
fifo_index <= push & ~pop ? fifo_index + 1'b1 :
~push & pop ? fifo_index - 1'b1 :
fifo_index;
end
end
assign push = s_valid & s_ready;
always @(posedge aclk) begin
if (~aresetn) begin
s_ready <= 1'b0;
end
else begin
s_ready <= areset_r1 ? 1'b1 :
push & ~pop && (fifo_index == (C_FIFO_DEPTH - 2'd2)) ? 1'b0 :
~push & pop ? 1'b1 :
s_ready;
end
end
assign pop = m_valid & m_ready;
always @(posedge aclk) begin
if (~aresetn) begin
m_valid <= 1'b0;
end
else begin
m_valid <= ~push & pop && (fifo_index == {LP_LOG_FIFO_DEPTH{1'b0}}) ? 1'b0 :
push & ~pop ? 1'b1 :
m_valid;
end
end
generate
if (LP_LOG_FIFO_DEPTH < 4) begin : gen_pad_fifo_addr
assign fifo_addr[0+:LP_LOG_FIFO_DEPTH] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
assign fifo_addr[LP_LOG_FIFO_DEPTH+:(4-LP_LOG_FIFO_DEPTH)] = {4-LP_LOG_FIFO_DEPTH{1'b0}};
end
else begin : gen_fifo_addr
assign fifo_addr[LP_LOG_FIFO_DEPTH-1:0] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
end
endgenerate
generate
genvar i;
for (i = 0; i < C_PAYLOAD_WIDTH; i = i + 1) begin : gen_data_bit
SRL16E
u_srl_fifo(
.Q ( m_payload[i] ) ,
.A0 ( fifo_addr[0] ) ,
.A1 ( fifo_addr[1] ) ,
.A2 ( fifo_addr[2] ) ,
.A3 ( fifo_addr[3] ) ,
.CE ( push ) ,
.CLK ( aclk ) ,
.D ( s_payload[i] )
);
end
endgenerate
endmodule |
module axi_infrastructure_v1_1_axic_srl_fifo #(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
parameter C_FAMILY = "virtex7",
parameter integer C_PAYLOAD_WIDTH = 1,
parameter integer C_FIFO_DEPTH = 16 // Range: 4-16.
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire aclk, // Clock
input wire aresetn, // Reset
input wire [C_PAYLOAD_WIDTH-1:0] s_payload, // Input data
input wire s_valid, // Input data valid
output reg s_ready, // Input data ready
output wire [C_PAYLOAD_WIDTH-1:0] m_payload, // Output data
output reg m_valid, // Output data valid
input wire m_ready // Output data ready
);
////////////////////////////////////////////////////////////////////////////////
// Functions
////////////////////////////////////////////////////////////////////////////////
// ceiling logb2
function integer f_clogb2 (input integer size);
integer s;
begin
s = size;
s = s - 1;
for (f_clogb2=1; s>1; f_clogb2=f_clogb2+1)
s = s >> 1;
end
endfunction // clogb2
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
localparam integer LP_LOG_FIFO_DEPTH = f_clogb2(C_FIFO_DEPTH);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [LP_LOG_FIFO_DEPTH-1:0] fifo_index;
wire [4-1:0] fifo_addr;
wire push;
wire pop ;
reg areset_r1;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
always @(posedge aclk) begin
areset_r1 <= ~aresetn;
end
always @(posedge aclk) begin
if (~aresetn) begin
fifo_index <= {LP_LOG_FIFO_DEPTH{1'b1}};
end
else begin
fifo_index <= push & ~pop ? fifo_index + 1'b1 :
~push & pop ? fifo_index - 1'b1 :
fifo_index;
end
end
assign push = s_valid & s_ready;
always @(posedge aclk) begin
if (~aresetn) begin
s_ready <= 1'b0;
end
else begin
s_ready <= areset_r1 ? 1'b1 :
push & ~pop && (fifo_index == (C_FIFO_DEPTH - 2'd2)) ? 1'b0 :
~push & pop ? 1'b1 :
s_ready;
end
end
assign pop = m_valid & m_ready;
always @(posedge aclk) begin
if (~aresetn) begin
m_valid <= 1'b0;
end
else begin
m_valid <= ~push & pop && (fifo_index == {LP_LOG_FIFO_DEPTH{1'b0}}) ? 1'b0 :
push & ~pop ? 1'b1 :
m_valid;
end
end
generate
if (LP_LOG_FIFO_DEPTH < 4) begin : gen_pad_fifo_addr
assign fifo_addr[0+:LP_LOG_FIFO_DEPTH] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
assign fifo_addr[LP_LOG_FIFO_DEPTH+:(4-LP_LOG_FIFO_DEPTH)] = {4-LP_LOG_FIFO_DEPTH{1'b0}};
end
else begin : gen_fifo_addr
assign fifo_addr[LP_LOG_FIFO_DEPTH-1:0] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
end
endgenerate
generate
genvar i;
for (i = 0; i < C_PAYLOAD_WIDTH; i = i + 1) begin : gen_data_bit
SRL16E
u_srl_fifo(
.Q ( m_payload[i] ) ,
.A0 ( fifo_addr[0] ) ,
.A1 ( fifo_addr[1] ) ,
.A2 ( fifo_addr[2] ) ,
.A3 ( fifo_addr[3] ) ,
.CE ( push ) ,
.CLK ( aclk ) ,
.D ( s_payload[i] )
);
end
endgenerate
endmodule |
module axi_infrastructure_v1_1_axic_srl_fifo #(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
parameter C_FAMILY = "virtex7",
parameter integer C_PAYLOAD_WIDTH = 1,
parameter integer C_FIFO_DEPTH = 16 // Range: 4-16.
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire aclk, // Clock
input wire aresetn, // Reset
input wire [C_PAYLOAD_WIDTH-1:0] s_payload, // Input data
input wire s_valid, // Input data valid
output reg s_ready, // Input data ready
output wire [C_PAYLOAD_WIDTH-1:0] m_payload, // Output data
output reg m_valid, // Output data valid
input wire m_ready // Output data ready
);
////////////////////////////////////////////////////////////////////////////////
// Functions
////////////////////////////////////////////////////////////////////////////////
// ceiling logb2
function integer f_clogb2 (input integer size);
integer s;
begin
s = size;
s = s - 1;
for (f_clogb2=1; s>1; f_clogb2=f_clogb2+1)
s = s >> 1;
end
endfunction // clogb2
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
localparam integer LP_LOG_FIFO_DEPTH = f_clogb2(C_FIFO_DEPTH);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [LP_LOG_FIFO_DEPTH-1:0] fifo_index;
wire [4-1:0] fifo_addr;
wire push;
wire pop ;
reg areset_r1;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
always @(posedge aclk) begin
areset_r1 <= ~aresetn;
end
always @(posedge aclk) begin
if (~aresetn) begin
fifo_index <= {LP_LOG_FIFO_DEPTH{1'b1}};
end
else begin
fifo_index <= push & ~pop ? fifo_index + 1'b1 :
~push & pop ? fifo_index - 1'b1 :
fifo_index;
end
end
assign push = s_valid & s_ready;
always @(posedge aclk) begin
if (~aresetn) begin
s_ready <= 1'b0;
end
else begin
s_ready <= areset_r1 ? 1'b1 :
push & ~pop && (fifo_index == (C_FIFO_DEPTH - 2'd2)) ? 1'b0 :
~push & pop ? 1'b1 :
s_ready;
end
end
assign pop = m_valid & m_ready;
always @(posedge aclk) begin
if (~aresetn) begin
m_valid <= 1'b0;
end
else begin
m_valid <= ~push & pop && (fifo_index == {LP_LOG_FIFO_DEPTH{1'b0}}) ? 1'b0 :
push & ~pop ? 1'b1 :
m_valid;
end
end
generate
if (LP_LOG_FIFO_DEPTH < 4) begin : gen_pad_fifo_addr
assign fifo_addr[0+:LP_LOG_FIFO_DEPTH] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
assign fifo_addr[LP_LOG_FIFO_DEPTH+:(4-LP_LOG_FIFO_DEPTH)] = {4-LP_LOG_FIFO_DEPTH{1'b0}};
end
else begin : gen_fifo_addr
assign fifo_addr[LP_LOG_FIFO_DEPTH-1:0] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
end
endgenerate
generate
genvar i;
for (i = 0; i < C_PAYLOAD_WIDTH; i = i + 1) begin : gen_data_bit
SRL16E
u_srl_fifo(
.Q ( m_payload[i] ) ,
.A0 ( fifo_addr[0] ) ,
.A1 ( fifo_addr[1] ) ,
.A2 ( fifo_addr[2] ) ,
.A3 ( fifo_addr[3] ) ,
.CE ( push ) ,
.CLK ( aclk ) ,
.D ( s_payload[i] )
);
end
endgenerate
endmodule |
module testbed_hi_read_tx;
reg pck0;
reg [7:0] adc_d;
reg shallow_modulation;
wire pwr_lo;
wire adc_clk;
reg ck_1356meg;
reg ck_1356megb;
wire ssp_frame;
wire ssp_din;
wire ssp_clk;
reg ssp_dout;
wire pwr_hi;
wire pwr_oe1;
wire pwr_oe2;
wire pwr_oe3;
wire pwr_oe4;
wire cross_lo;
wire cross_hi;
wire dbg;
hi_read_tx #(5,200) dut(
.pck0(pck0),
.ck_1356meg(ck_1356meg),
.ck_1356megb(ck_1356megb),
.pwr_lo(pwr_lo),
.pwr_hi(pwr_hi),
.pwr_oe1(pwr_oe1),
.pwr_oe2(pwr_oe2),
.pwr_oe3(pwr_oe3),
.pwr_oe4(pwr_oe4),
.adc_d(adc_d),
.adc_clk(adc_clk),
.ssp_frame(ssp_frame),
.ssp_din(ssp_din),
.ssp_dout(ssp_dout),
.ssp_clk(ssp_clk),
.cross_hi(cross_hi),
.cross_lo(cross_lo),
.dbg(dbg),
.shallow_modulation(shallow_modulation)
);
integer idx, i;
// main clock
always #5 begin
ck_1356megb = !ck_1356megb;
ck_1356meg = ck_1356megb;
end
//crank DUT
task crank_dut;
begin
@(posedge ssp_clk) ;
ssp_dout = $random;
end
endtask
initial begin
// init inputs
ck_1356megb = 0;
adc_d = 0;
ssp_dout=0;
// shallow modulation off
shallow_modulation=0;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
// shallow modulation on
shallow_modulation=1;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
$finish;
end
endmodule |
module
output wire b_push ,
output wire [C_ID_WIDTH-1:0] b_awid ,
output wire [7:0] b_awlen ,
input wire b_full
);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
wire next ;
wire next_pending ;
wire a_push;
wire incr_burst;
reg [C_ID_WIDTH-1:0] s_awid_r;
reg [7:0] s_awlen_r;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// Translate the AXI transaction to the MC transaction(s)
axi_protocol_converter_v2_1_b2s_cmd_translator #
(
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH )
)
cmd_translator_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_axaddr ( s_awaddr ) ,
.s_axlen ( s_awlen ) ,
.s_axsize ( s_awsize ) ,
.s_axburst ( s_awburst ) ,
.s_axhandshake ( s_awvalid & a_push ) ,
.m_axaddr ( m_awaddr ) ,
.incr_burst ( incr_burst ) ,
.next ( next ) ,
.next_pending ( next_pending )
);
axi_protocol_converter_v2_1_b2s_wr_cmd_fsm aw_cmd_fsm_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_awready ( s_awready ) ,
.s_awvalid ( s_awvalid ) ,
.m_awvalid ( m_awvalid ) ,
.m_awready ( m_awready ) ,
.next ( next ) ,
.next_pending ( next_pending ) ,
.b_push ( b_push ) ,
.b_full ( b_full ) ,
.a_push ( a_push )
);
assign b_awid = s_awid_r;
assign b_awlen = s_awlen_r;
always @(posedge clk) begin
s_awid_r <= s_awid ;
s_awlen_r <= s_awlen ;
end
endmodule |
module
output wire b_push ,
output wire [C_ID_WIDTH-1:0] b_awid ,
output wire [7:0] b_awlen ,
input wire b_full
);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
wire next ;
wire next_pending ;
wire a_push;
wire incr_burst;
reg [C_ID_WIDTH-1:0] s_awid_r;
reg [7:0] s_awlen_r;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// Translate the AXI transaction to the MC transaction(s)
axi_protocol_converter_v2_1_b2s_cmd_translator #
(
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH )
)
cmd_translator_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_axaddr ( s_awaddr ) ,
.s_axlen ( s_awlen ) ,
.s_axsize ( s_awsize ) ,
.s_axburst ( s_awburst ) ,
.s_axhandshake ( s_awvalid & a_push ) ,
.m_axaddr ( m_awaddr ) ,
.incr_burst ( incr_burst ) ,
.next ( next ) ,
.next_pending ( next_pending )
);
axi_protocol_converter_v2_1_b2s_wr_cmd_fsm aw_cmd_fsm_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_awready ( s_awready ) ,
.s_awvalid ( s_awvalid ) ,
.m_awvalid ( m_awvalid ) ,
.m_awready ( m_awready ) ,
.next ( next ) ,
.next_pending ( next_pending ) ,
.b_push ( b_push ) ,
.b_full ( b_full ) ,
.a_push ( a_push )
);
assign b_awid = s_awid_r;
assign b_awlen = s_awlen_r;
always @(posedge clk) begin
s_awid_r <= s_awid ;
s_awlen_r <= s_awlen ;
end
endmodule |
module
output wire b_push ,
output wire [C_ID_WIDTH-1:0] b_awid ,
output wire [7:0] b_awlen ,
input wire b_full
);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
wire next ;
wire next_pending ;
wire a_push;
wire incr_burst;
reg [C_ID_WIDTH-1:0] s_awid_r;
reg [7:0] s_awlen_r;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// Translate the AXI transaction to the MC transaction(s)
axi_protocol_converter_v2_1_b2s_cmd_translator #
(
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH )
)
cmd_translator_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_axaddr ( s_awaddr ) ,
.s_axlen ( s_awlen ) ,
.s_axsize ( s_awsize ) ,
.s_axburst ( s_awburst ) ,
.s_axhandshake ( s_awvalid & a_push ) ,
.m_axaddr ( m_awaddr ) ,
.incr_burst ( incr_burst ) ,
.next ( next ) ,
.next_pending ( next_pending )
);
axi_protocol_converter_v2_1_b2s_wr_cmd_fsm aw_cmd_fsm_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_awready ( s_awready ) ,
.s_awvalid ( s_awvalid ) ,
.m_awvalid ( m_awvalid ) ,
.m_awready ( m_awready ) ,
.next ( next ) ,
.next_pending ( next_pending ) ,
.b_push ( b_push ) ,
.b_full ( b_full ) ,
.a_push ( a_push )
);
assign b_awid = s_awid_r;
assign b_awlen = s_awlen_r;
always @(posedge clk) begin
s_awid_r <= s_awid ;
s_awlen_r <= s_awlen ;
end
endmodule |
module Priority_Codec_64(
input wire [54:0] Data_Dec_i,
output reg [5:0] Data_Bin_o
);
always @(Data_Dec_i)
begin
Data_Bin_o=6'b000000;
if(~Data_Dec_i[54]) begin Data_Bin_o = 6'b000000;//0
end else if(~Data_Dec_i[53]) begin Data_Bin_o = 6'b000001;//1
end else if(~Data_Dec_i[52]) begin Data_Bin_o = 6'b000010;//2
end else if(~Data_Dec_i[51]) begin Data_Bin_o = 6'b000011;//3
end else if(~Data_Dec_i[50]) begin Data_Bin_o = 6'b000100;//4
end else if(~Data_Dec_i[49]) begin Data_Bin_o = 6'b000101;//5
end else if(~Data_Dec_i[48]) begin Data_Bin_o = 6'b000110;//6
end else if(~Data_Dec_i[47]) begin Data_Bin_o = 6'b000111;//7
end else if(~Data_Dec_i[46]) begin Data_Bin_o = 6'b001000;//8
end else if(~Data_Dec_i[45]) begin Data_Bin_o = 6'b001001;//9
end else if(~Data_Dec_i[44]) begin Data_Bin_o = 6'b001010;//10
end else if(~Data_Dec_i[43]) begin Data_Bin_o = 6'b001011;//11
end else if(~Data_Dec_i[42]) begin Data_Bin_o = 6'b001100;//12
end else if(~Data_Dec_i[41]) begin Data_Bin_o = 6'b001101;//13
end else if(~Data_Dec_i[40]) begin Data_Bin_o = 6'b001110;//14
end else if(~Data_Dec_i[39]) begin Data_Bin_o = 6'b001111;//15
end else if(~Data_Dec_i[38]) begin Data_Bin_o = 6'b010000;//16
end else if(~Data_Dec_i[37]) begin Data_Bin_o = 6'b010001;//17
end else if(~Data_Dec_i[36]) begin Data_Bin_o = 6'b010010;//18
end else if(~Data_Dec_i[35]) begin Data_Bin_o = 6'b010011;//19
end else if(~Data_Dec_i[34]) begin Data_Bin_o = 6'b010100;//20
end else if(~Data_Dec_i[33]) begin Data_Bin_o = 6'b010101;//21
end else if(~Data_Dec_i[32]) begin Data_Bin_o = 6'b010110;//22
end else if(~Data_Dec_i[31]) begin Data_Bin_o = 6'b010111;//23
end else if(~Data_Dec_i[30]) begin Data_Bin_o = 6'b011000;//24
end else if(~Data_Dec_i[29]) begin Data_Bin_o = 6'b010101;//25
end else if(~Data_Dec_i[28]) begin Data_Bin_o = 6'b010110;//26
end else if(~Data_Dec_i[27]) begin Data_Bin_o = 6'b010111;//27
end else if(~Data_Dec_i[26]) begin Data_Bin_o = 6'b011000;//28
end else if(~Data_Dec_i[25]) begin Data_Bin_o = 6'b011001;//29
end else if(~Data_Dec_i[24]) begin Data_Bin_o = 6'b011010;//30
end else if(~Data_Dec_i[23]) begin Data_Bin_o = 6'b011011;//31
end else if(~Data_Dec_i[22]) begin Data_Bin_o = 6'b011100;//32
end else if(~Data_Dec_i[21]) begin Data_Bin_o = 6'b011101;//33
end else if(~Data_Dec_i[20]) begin Data_Bin_o = 6'b011110;//34
end else if(~Data_Dec_i[19]) begin Data_Bin_o = 6'b011111;//35
end else if(~Data_Dec_i[18]) begin Data_Bin_o = 6'b100000;//36
end else if(~Data_Dec_i[17]) begin Data_Bin_o = 6'b100001;//37
end else if(~Data_Dec_i[16]) begin Data_Bin_o = 6'b100010;//38
end else if(~Data_Dec_i[15]) begin Data_Bin_o = 6'b100011;//39
end else if(~Data_Dec_i[14]) begin Data_Bin_o = 6'b100100;//40
end else if(~Data_Dec_i[13]) begin Data_Bin_o = 6'b100101;//41
end else if(~Data_Dec_i[12]) begin Data_Bin_o = 6'b100110;//42
end else if(~Data_Dec_i[11]) begin Data_Bin_o = 6'b100111;//43
end else if(~Data_Dec_i[10]) begin Data_Bin_o = 6'b101000;//44
end else if(~Data_Dec_i[9]) begin Data_Bin_o = 6'b101001;//45
end else if(~Data_Dec_i[8]) begin Data_Bin_o = 6'b101010;//46
end else if(~Data_Dec_i[7]) begin Data_Bin_o = 6'b101011;//47
end else if(~Data_Dec_i[6]) begin Data_Bin_o = 6'b101100;//48
end else if(~Data_Dec_i[5]) begin Data_Bin_o = 6'b101101;//49
end else if(~Data_Dec_i[4]) begin Data_Bin_o = 6'b101110;//50
end else if(~Data_Dec_i[3]) begin Data_Bin_o = 6'b101111;//51
end else if(~Data_Dec_i[2]) begin Data_Bin_o = 6'b110000;//52
end else if(~Data_Dec_i[1]) begin Data_Bin_o = 6'b110001;//53
end else if(~Data_Dec_i[0]) begin Data_Bin_o = 6'b110010;//54
end else begin Data_Bin_o = 6'b000000;//zero value
end
end
endmodule |
module Priority_Codec_64(
input wire [54:0] Data_Dec_i,
output reg [5:0] Data_Bin_o
);
always @(Data_Dec_i)
begin
Data_Bin_o=6'b000000;
if(~Data_Dec_i[54]) begin Data_Bin_o = 6'b000000;//0
end else if(~Data_Dec_i[53]) begin Data_Bin_o = 6'b000001;//1
end else if(~Data_Dec_i[52]) begin Data_Bin_o = 6'b000010;//2
end else if(~Data_Dec_i[51]) begin Data_Bin_o = 6'b000011;//3
end else if(~Data_Dec_i[50]) begin Data_Bin_o = 6'b000100;//4
end else if(~Data_Dec_i[49]) begin Data_Bin_o = 6'b000101;//5
end else if(~Data_Dec_i[48]) begin Data_Bin_o = 6'b000110;//6
end else if(~Data_Dec_i[47]) begin Data_Bin_o = 6'b000111;//7
end else if(~Data_Dec_i[46]) begin Data_Bin_o = 6'b001000;//8
end else if(~Data_Dec_i[45]) begin Data_Bin_o = 6'b001001;//9
end else if(~Data_Dec_i[44]) begin Data_Bin_o = 6'b001010;//10
end else if(~Data_Dec_i[43]) begin Data_Bin_o = 6'b001011;//11
end else if(~Data_Dec_i[42]) begin Data_Bin_o = 6'b001100;//12
end else if(~Data_Dec_i[41]) begin Data_Bin_o = 6'b001101;//13
end else if(~Data_Dec_i[40]) begin Data_Bin_o = 6'b001110;//14
end else if(~Data_Dec_i[39]) begin Data_Bin_o = 6'b001111;//15
end else if(~Data_Dec_i[38]) begin Data_Bin_o = 6'b010000;//16
end else if(~Data_Dec_i[37]) begin Data_Bin_o = 6'b010001;//17
end else if(~Data_Dec_i[36]) begin Data_Bin_o = 6'b010010;//18
end else if(~Data_Dec_i[35]) begin Data_Bin_o = 6'b010011;//19
end else if(~Data_Dec_i[34]) begin Data_Bin_o = 6'b010100;//20
end else if(~Data_Dec_i[33]) begin Data_Bin_o = 6'b010101;//21
end else if(~Data_Dec_i[32]) begin Data_Bin_o = 6'b010110;//22
end else if(~Data_Dec_i[31]) begin Data_Bin_o = 6'b010111;//23
end else if(~Data_Dec_i[30]) begin Data_Bin_o = 6'b011000;//24
end else if(~Data_Dec_i[29]) begin Data_Bin_o = 6'b010101;//25
end else if(~Data_Dec_i[28]) begin Data_Bin_o = 6'b010110;//26
end else if(~Data_Dec_i[27]) begin Data_Bin_o = 6'b010111;//27
end else if(~Data_Dec_i[26]) begin Data_Bin_o = 6'b011000;//28
end else if(~Data_Dec_i[25]) begin Data_Bin_o = 6'b011001;//29
end else if(~Data_Dec_i[24]) begin Data_Bin_o = 6'b011010;//30
end else if(~Data_Dec_i[23]) begin Data_Bin_o = 6'b011011;//31
end else if(~Data_Dec_i[22]) begin Data_Bin_o = 6'b011100;//32
end else if(~Data_Dec_i[21]) begin Data_Bin_o = 6'b011101;//33
end else if(~Data_Dec_i[20]) begin Data_Bin_o = 6'b011110;//34
end else if(~Data_Dec_i[19]) begin Data_Bin_o = 6'b011111;//35
end else if(~Data_Dec_i[18]) begin Data_Bin_o = 6'b100000;//36
end else if(~Data_Dec_i[17]) begin Data_Bin_o = 6'b100001;//37
end else if(~Data_Dec_i[16]) begin Data_Bin_o = 6'b100010;//38
end else if(~Data_Dec_i[15]) begin Data_Bin_o = 6'b100011;//39
end else if(~Data_Dec_i[14]) begin Data_Bin_o = 6'b100100;//40
end else if(~Data_Dec_i[13]) begin Data_Bin_o = 6'b100101;//41
end else if(~Data_Dec_i[12]) begin Data_Bin_o = 6'b100110;//42
end else if(~Data_Dec_i[11]) begin Data_Bin_o = 6'b100111;//43
end else if(~Data_Dec_i[10]) begin Data_Bin_o = 6'b101000;//44
end else if(~Data_Dec_i[9]) begin Data_Bin_o = 6'b101001;//45
end else if(~Data_Dec_i[8]) begin Data_Bin_o = 6'b101010;//46
end else if(~Data_Dec_i[7]) begin Data_Bin_o = 6'b101011;//47
end else if(~Data_Dec_i[6]) begin Data_Bin_o = 6'b101100;//48
end else if(~Data_Dec_i[5]) begin Data_Bin_o = 6'b101101;//49
end else if(~Data_Dec_i[4]) begin Data_Bin_o = 6'b101110;//50
end else if(~Data_Dec_i[3]) begin Data_Bin_o = 6'b101111;//51
end else if(~Data_Dec_i[2]) begin Data_Bin_o = 6'b110000;//52
end else if(~Data_Dec_i[1]) begin Data_Bin_o = 6'b110001;//53
end else if(~Data_Dec_i[0]) begin Data_Bin_o = 6'b110010;//54
end else begin Data_Bin_o = 6'b000000;//zero value
end
end
endmodule |
module halfband_decim
(input clock, input reset, input enable, input strobe_in, output wire strobe_out,
input wire [15:0] data_in, output reg [15:0] data_out,output wire [15:0] debugctrl);
reg [3:0] rd_addr1;
reg [3:0] rd_addr2;
reg [3:0] phase;
reg [3:0] base_addr;
wire signed [15:0] mac_out,middle_data, sum, coeff;
wire signed [30:0] product;
wire signed [33:0] sum_even;
wire clear;
reg store_odd;
always @(posedge clock)
if(reset)
store_odd <= #1 1'b0;
else
if(strobe_in)
store_odd <= #1 ~store_odd;
wire start = strobe_in & store_odd;
always @(posedge clock)
if(reset)
base_addr <= #1 4'd0;
else if(start)
base_addr <= #1 base_addr + 4'd1;
always @(posedge clock)
if(reset)
phase <= #1 4'd8;
else if (start)
phase <= #1 4'd0;
else if(phase != 4'd8)
phase <= #1 phase + 4'd1;
reg start_d1,start_d2,start_d3,start_d4,start_d5,start_d6,start_d7,start_d8,start_d9,start_dA,start_dB,start_dC,start_dD;
always @(posedge clock)
begin
start_d1 <= #1 start;
start_d2 <= #1 start_d1;
start_d3 <= #1 start_d2;
start_d4 <= #1 start_d3;
start_d5 <= #1 start_d4;
start_d6 <= #1 start_d5;
start_d7 <= #1 start_d6;
start_d8 <= #1 start_d7;
start_d9 <= #1 start_d8;
start_dA <= #1 start_d9;
start_dB <= #1 start_dA;
start_dC <= #1 start_dB;
start_dD <= #1 start_dC;
end // always @ (posedge clock)
reg mult_en, mult_en_pre;
always @(posedge clock)
begin
mult_en_pre <= #1 phase!=8;
mult_en <= #1 mult_en_pre;
end
assign clear = start_d4; // was dC
wire latch_result = start_d4; // was dC
assign strobe_out = start_d5; // was dD
wire acc_en;
always @*
case(phase[2:0])
3'd0 : begin rd_addr1 = base_addr + 4'd0; rd_addr2 = base_addr + 4'd15; end
3'd1 : begin rd_addr1 = base_addr + 4'd1; rd_addr2 = base_addr + 4'd14; end
3'd2 : begin rd_addr1 = base_addr + 4'd2; rd_addr2 = base_addr + 4'd13; end
3'd3 : begin rd_addr1 = base_addr + 4'd3; rd_addr2 = base_addr + 4'd12; end
3'd4 : begin rd_addr1 = base_addr + 4'd4; rd_addr2 = base_addr + 4'd11; end
3'd5 : begin rd_addr1 = base_addr + 4'd5; rd_addr2 = base_addr + 4'd10; end
3'd6 : begin rd_addr1 = base_addr + 4'd6; rd_addr2 = base_addr + 4'd9; end
3'd7 : begin rd_addr1 = base_addr + 4'd7; rd_addr2 = base_addr + 4'd8; end
default: begin rd_addr1 = base_addr + 4'd0; rd_addr2 = base_addr + 4'd15; end
endcase // case(phase)
coeff_rom coeff_rom (.clock(clock),.addr(phase[2:0]-3'd1),.data(coeff));
ram16_2sum ram16_even (.clock(clock),.write(strobe_in & ~store_odd),
.wr_addr(base_addr),.wr_data(data_in),
.rd_addr1(rd_addr1),.rd_addr2(rd_addr2),
.sum(sum));
ram16 ram16_odd (.clock(clock),.write(strobe_in & store_odd), // Holds middle items
.wr_addr(base_addr),.wr_data(data_in),
//.rd_addr(base_addr+4'd7),.rd_data(middle_data));
.rd_addr(base_addr+4'd6),.rd_data(middle_data));
mult mult(.clock(clock),.x(coeff),.y(sum),.product(product),.enable_in(mult_en),.enable_out(acc_en));
acc acc(.clock(clock),.reset(reset),.enable_in(acc_en),.enable_out(),
.clear(clear),.addend(product),.sum(sum_even));
wire signed [33:0] dout = sum_even + {{4{middle_data[15]}},middle_data,14'b0}; // We already divided product by 2!!!!
always @(posedge clock)
if(reset)
data_out <= #1 16'd0;
else if(latch_result)
data_out <= #1 dout[30:15] + (dout[33]& |dout[14:0]);
assign debugctrl = { clock,reset,acc_en,mult_en,clear,latch_result,store_odd,strobe_in,strobe_out,phase};
endmodule |
module halfband_decim
(input clock, input reset, input enable, input strobe_in, output wire strobe_out,
input wire [15:0] data_in, output reg [15:0] data_out,output wire [15:0] debugctrl);
reg [3:0] rd_addr1;
reg [3:0] rd_addr2;
reg [3:0] phase;
reg [3:0] base_addr;
wire signed [15:0] mac_out,middle_data, sum, coeff;
wire signed [30:0] product;
wire signed [33:0] sum_even;
wire clear;
reg store_odd;
always @(posedge clock)
if(reset)
store_odd <= #1 1'b0;
else
if(strobe_in)
store_odd <= #1 ~store_odd;
wire start = strobe_in & store_odd;
always @(posedge clock)
if(reset)
base_addr <= #1 4'd0;
else if(start)
base_addr <= #1 base_addr + 4'd1;
always @(posedge clock)
if(reset)
phase <= #1 4'd8;
else if (start)
phase <= #1 4'd0;
else if(phase != 4'd8)
phase <= #1 phase + 4'd1;
reg start_d1,start_d2,start_d3,start_d4,start_d5,start_d6,start_d7,start_d8,start_d9,start_dA,start_dB,start_dC,start_dD;
always @(posedge clock)
begin
start_d1 <= #1 start;
start_d2 <= #1 start_d1;
start_d3 <= #1 start_d2;
start_d4 <= #1 start_d3;
start_d5 <= #1 start_d4;
start_d6 <= #1 start_d5;
start_d7 <= #1 start_d6;
start_d8 <= #1 start_d7;
start_d9 <= #1 start_d8;
start_dA <= #1 start_d9;
start_dB <= #1 start_dA;
start_dC <= #1 start_dB;
start_dD <= #1 start_dC;
end // always @ (posedge clock)
reg mult_en, mult_en_pre;
always @(posedge clock)
begin
mult_en_pre <= #1 phase!=8;
mult_en <= #1 mult_en_pre;
end
assign clear = start_d4; // was dC
wire latch_result = start_d4; // was dC
assign strobe_out = start_d5; // was dD
wire acc_en;
always @*
case(phase[2:0])
3'd0 : begin rd_addr1 = base_addr + 4'd0; rd_addr2 = base_addr + 4'd15; end
3'd1 : begin rd_addr1 = base_addr + 4'd1; rd_addr2 = base_addr + 4'd14; end
3'd2 : begin rd_addr1 = base_addr + 4'd2; rd_addr2 = base_addr + 4'd13; end
3'd3 : begin rd_addr1 = base_addr + 4'd3; rd_addr2 = base_addr + 4'd12; end
3'd4 : begin rd_addr1 = base_addr + 4'd4; rd_addr2 = base_addr + 4'd11; end
3'd5 : begin rd_addr1 = base_addr + 4'd5; rd_addr2 = base_addr + 4'd10; end
3'd6 : begin rd_addr1 = base_addr + 4'd6; rd_addr2 = base_addr + 4'd9; end
3'd7 : begin rd_addr1 = base_addr + 4'd7; rd_addr2 = base_addr + 4'd8; end
default: begin rd_addr1 = base_addr + 4'd0; rd_addr2 = base_addr + 4'd15; end
endcase // case(phase)
coeff_rom coeff_rom (.clock(clock),.addr(phase[2:0]-3'd1),.data(coeff));
ram16_2sum ram16_even (.clock(clock),.write(strobe_in & ~store_odd),
.wr_addr(base_addr),.wr_data(data_in),
.rd_addr1(rd_addr1),.rd_addr2(rd_addr2),
.sum(sum));
ram16 ram16_odd (.clock(clock),.write(strobe_in & store_odd), // Holds middle items
.wr_addr(base_addr),.wr_data(data_in),
//.rd_addr(base_addr+4'd7),.rd_data(middle_data));
.rd_addr(base_addr+4'd6),.rd_data(middle_data));
mult mult(.clock(clock),.x(coeff),.y(sum),.product(product),.enable_in(mult_en),.enable_out(acc_en));
acc acc(.clock(clock),.reset(reset),.enable_in(acc_en),.enable_out(),
.clear(clear),.addend(product),.sum(sum_even));
wire signed [33:0] dout = sum_even + {{4{middle_data[15]}},middle_data,14'b0}; // We already divided product by 2!!!!
always @(posedge clock)
if(reset)
data_out <= #1 16'd0;
else if(latch_result)
data_out <= #1 dout[30:15] + (dout[33]& |dout[14:0]);
assign debugctrl = { clock,reset,acc_en,mult_en,clear,latch_result,store_odd,strobe_in,strobe_out,phase};
endmodule |
module axi_data_fifo_v2_1_axi_data_fifo #
(
parameter C_FAMILY = "virtex7",
parameter integer C_AXI_PROTOCOL = 0,
parameter integer C_AXI_ID_WIDTH = 4,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_USER_SIGNALS = 0,
parameter integer C_AXI_AWUSER_WIDTH = 1,
parameter integer C_AXI_ARUSER_WIDTH = 1,
parameter integer C_AXI_WUSER_WIDTH = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1,
parameter integer C_AXI_WRITE_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_WRITE_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_WRITE_FIFO_DELAY = 0, // 0 = No, 1 = Yes
// Indicates whether AWVALID and WVALID assertion is delayed until:
// a. the corresponding WLAST is stored in the FIFO, or
// b. no WLAST is stored and the FIFO is full.
// 0 means AW channel is pass-through and
// WVALID is asserted whenever FIFO is not empty.
parameter integer C_AXI_READ_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_READ_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_READ_FIFO_DELAY = 0) // 0 = No, 1 = Yes
// Indicates whether ARVALID assertion is delayed until the
// the remaining vacancy of the FIFO is at least the burst length
// as indicated by ARLEN.
// 0 means AR channel is pass-through.
// System Signals
(input wire aclk,
input wire aresetn,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_awaddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_awlen,
input wire [3-1:0] s_axi_awsize,
input wire [2-1:0] s_axi_awburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_awlock,
input wire [4-1:0] s_axi_awcache,
input wire [3-1:0] s_axi_awprot,
input wire [4-1:0] s_axi_awregion,
input wire [4-1:0] s_axi_awqos,
input wire [C_AXI_AWUSER_WIDTH-1:0] s_axi_awuser,
input wire s_axi_awvalid,
output wire s_axi_awready,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_wid,
input wire [C_AXI_DATA_WIDTH-1:0] s_axi_wdata,
input wire [C_AXI_DATA_WIDTH/8-1:0] s_axi_wstrb,
input wire s_axi_wlast,
input wire [C_AXI_WUSER_WIDTH-1:0] s_axi_wuser,
input wire s_axi_wvalid,
output wire s_axi_wready,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output wire [2-1:0] s_axi_bresp,
output wire [C_AXI_BUSER_WIDTH-1:0] s_axi_buser,
output wire s_axi_bvalid,
input wire s_axi_bready,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_araddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_arlen,
input wire [3-1:0] s_axi_arsize,
input wire [2-1:0] s_axi_arburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_arlock,
input wire [4-1:0] s_axi_arcache,
input wire [3-1:0] s_axi_arprot,
input wire [4-1:0] s_axi_arregion,
input wire [4-1:0] s_axi_arqos,
input wire [C_AXI_ARUSER_WIDTH-1:0] s_axi_aruser,
input wire s_axi_arvalid,
output wire s_axi_arready,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output wire [C_AXI_DATA_WIDTH-1:0] s_axi_rdata,
output wire [2-1:0] s_axi_rresp,
output wire s_axi_rlast,
output wire [C_AXI_RUSER_WIDTH-1:0] s_axi_ruser,
output wire s_axi_rvalid,
input wire s_axi_rready,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_awid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_awaddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_awlen,
output wire [3-1:0] m_axi_awsize,
output wire [2-1:0] m_axi_awburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_awlock,
output wire [4-1:0] m_axi_awcache,
output wire [3-1:0] m_axi_awprot,
output wire [4-1:0] m_axi_awregion,
output wire [4-1:0] m_axi_awqos,
output wire [C_AXI_AWUSER_WIDTH-1:0] m_axi_awuser,
output wire m_axi_awvalid,
input wire m_axi_awready,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] m_axi_wid,
output wire [C_AXI_DATA_WIDTH-1:0] m_axi_wdata,
output wire [C_AXI_DATA_WIDTH/8-1:0] m_axi_wstrb,
output wire m_axi_wlast,
output wire [C_AXI_WUSER_WIDTH-1:0] m_axi_wuser,
output wire m_axi_wvalid,
input wire m_axi_wready,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_bid,
input wire [2-1:0] m_axi_bresp,
input wire [C_AXI_BUSER_WIDTH-1:0] m_axi_buser,
input wire m_axi_bvalid,
output wire m_axi_bready,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_arid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_araddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_arlen,
output wire [3-1:0] m_axi_arsize,
output wire [2-1:0] m_axi_arburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_arlock,
output wire [4-1:0] m_axi_arcache,
output wire [3-1:0] m_axi_arprot,
output wire [4-1:0] m_axi_arregion,
output wire [4-1:0] m_axi_arqos,
output wire [C_AXI_ARUSER_WIDTH-1:0] m_axi_aruser,
output wire m_axi_arvalid,
input wire m_axi_arready,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_rid,
input wire [C_AXI_DATA_WIDTH-1:0] m_axi_rdata,
input wire [2-1:0] m_axi_rresp,
input wire m_axi_rlast,
input wire [C_AXI_RUSER_WIDTH-1:0] m_axi_ruser,
input wire m_axi_rvalid,
output wire m_axi_rready);
localparam integer P_WIDTH_RACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_ARUSER_WIDTH;
localparam integer P_WIDTH_WACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_AWUSER_WIDTH;
localparam integer P_WIDTH_RDCH = 1 + 2 + C_AXI_DATA_WIDTH + C_AXI_ID_WIDTH + C_AXI_RUSER_WIDTH;
localparam integer P_WIDTH_WDCH = 1+C_AXI_DATA_WIDTH+C_AXI_DATA_WIDTH/8+((C_AXI_PROTOCOL==1)?C_AXI_ID_WIDTH:0)+C_AXI_WUSER_WIDTH;
localparam integer P_WIDTH_WRCH = 2 + C_AXI_ID_WIDTH + C_AXI_BUSER_WIDTH;
localparam P_PRIM_FIFO_TYPE = "512x72" ;
localparam integer P_AXI4 = 0;
localparam integer P_AXI3 = 1;
localparam integer P_AXILITE = 2;
localparam integer P_WRITE_FIFO_DEPTH_LOG = (C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1;
localparam integer P_READ_FIFO_DEPTH_LOG = (C_AXI_READ_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1;
// Ceiling of log2(x)
function integer f_ceil_log2
(
input integer x
);
integer acc;
begin
acc=0;
while ((2**acc) < x)
acc = acc + 1;
f_ceil_log2 = acc;
end
endfunction
generate
if (((C_AXI_WRITE_FIFO_DEPTH == 0) && (C_AXI_READ_FIFO_DEPTH == 0)) || (C_AXI_PROTOCOL == P_AXILITE)) begin : gen_bypass
assign m_axi_awid = s_axi_awid;
assign m_axi_awaddr = s_axi_awaddr;
assign m_axi_awlen = s_axi_awlen;
assign m_axi_awsize = s_axi_awsize;
assign m_axi_awburst = s_axi_awburst;
assign m_axi_awlock = s_axi_awlock;
assign m_axi_awcache = s_axi_awcache;
assign m_axi_awprot = s_axi_awprot;
assign m_axi_awregion = s_axi_awregion;
assign m_axi_awqos = s_axi_awqos;
assign m_axi_awuser = s_axi_awuser;
assign m_axi_awvalid = s_axi_awvalid;
assign s_axi_awready = m_axi_awready;
assign m_axi_wid = s_axi_wid;
assign m_axi_wdata = s_axi_wdata;
assign m_axi_wstrb = s_axi_wstrb;
assign m_axi_wlast = s_axi_wlast;
assign m_axi_wuser = s_axi_wuser;
assign m_axi_wvalid = s_axi_wvalid;
assign s_axi_wready = m_axi_wready;
assign s_axi_bid = m_axi_bid;
assign s_axi_bresp = m_axi_bresp;
assign s_axi_buser = m_axi_buser;
assign s_axi_bvalid = m_axi_bvalid;
assign m_axi_bready = s_axi_bready;
assign m_axi_arid = s_axi_arid;
assign m_axi_araddr = s_axi_araddr;
assign m_axi_arlen = s_axi_arlen;
assign m_axi_arsize = s_axi_arsize;
assign m_axi_arburst = s_axi_arburst;
assign m_axi_arlock = s_axi_arlock;
assign m_axi_arcache = s_axi_arcache;
assign m_axi_arprot = s_axi_arprot;
assign m_axi_arregion = s_axi_arregion;
assign m_axi_arqos = s_axi_arqos;
assign m_axi_aruser = s_axi_aruser;
assign m_axi_arvalid = s_axi_arvalid;
assign s_axi_arready = m_axi_arready;
assign s_axi_rid = m_axi_rid;
assign s_axi_rdata = m_axi_rdata;
assign s_axi_rresp = m_axi_rresp;
assign s_axi_rlast = m_axi_rlast;
assign s_axi_ruser = m_axi_ruser;
assign s_axi_rvalid = m_axi_rvalid;
assign m_axi_rready = s_axi_rready;
end else begin : gen_fifo
wire [4-1:0] s_axi_awregion_i;
wire [4-1:0] s_axi_arregion_i;
wire [4-1:0] m_axi_awregion_i;
wire [4-1:0] m_axi_arregion_i;
wire [C_AXI_ID_WIDTH-1:0] s_axi_wid_i;
wire [C_AXI_ID_WIDTH-1:0] m_axi_wid_i;
assign s_axi_awregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_awregion;
assign s_axi_arregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_arregion;
assign m_axi_awregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_awregion_i;
assign m_axi_arregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_arregion_i;
assign s_axi_wid_i = (C_AXI_PROTOCOL == P_AXI3) ? s_axi_wid : {C_AXI_ID_WIDTH{1'b0}};
assign m_axi_wid = (C_AXI_PROTOCOL == P_AXI3) ? m_axi_wid_i : {C_AXI_ID_WIDTH{1'b0}};
fifo_generator_v12_0 #(
.C_INTERFACE_TYPE(2),
.C_AXI_TYPE((C_AXI_PROTOCOL == P_AXI4) ? 1 : 3),
.C_AXI_DATA_WIDTH(C_AXI_DATA_WIDTH),
.C_AXI_ID_WIDTH(C_AXI_ID_WIDTH),
.C_HAS_AXI_ID(1),
.C_AXI_LEN_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 8 : 4),
.C_AXI_LOCK_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 1 : 2),
.C_HAS_AXI_ARUSER(1),
.C_HAS_AXI_AWUSER(1),
.C_HAS_AXI_BUSER(1),
.C_HAS_AXI_RUSER(1),
.C_HAS_AXI_WUSER(1),
.C_AXI_ADDR_WIDTH(C_AXI_ADDR_WIDTH),
.C_AXI_ARUSER_WIDTH(C_AXI_ARUSER_WIDTH),
.C_AXI_AWUSER_WIDTH(C_AXI_AWUSER_WIDTH),
.C_AXI_BUSER_WIDTH(C_AXI_BUSER_WIDTH),
.C_AXI_RUSER_WIDTH(C_AXI_RUSER_WIDTH),
.C_AXI_WUSER_WIDTH(C_AXI_WUSER_WIDTH),
.C_DIN_WIDTH_RACH(P_WIDTH_RACH),
.C_DIN_WIDTH_RDCH(P_WIDTH_RDCH),
.C_DIN_WIDTH_WACH(P_WIDTH_WACH),
.C_DIN_WIDTH_WDCH(P_WIDTH_WDCH),
.C_DIN_WIDTH_WRCH(P_WIDTH_WDCH),
.C_RACH_TYPE(((C_AXI_READ_FIFO_DEPTH != 0) && C_AXI_READ_FIFO_DELAY) ? 0 : 2),
.C_WACH_TYPE(((C_AXI_WRITE_FIFO_DEPTH != 0) && C_AXI_WRITE_FIFO_DELAY) ? 0 : 2),
.C_WDCH_TYPE((C_AXI_WRITE_FIFO_DEPTH != 0) ? 0 : 2),
.C_RDCH_TYPE((C_AXI_READ_FIFO_DEPTH != 0) ? 0 : 2),
.C_WRCH_TYPE(2),
.C_COMMON_CLOCK(1),
.C_ADD_NGC_CONSTRAINT(0),
.C_APPLICATION_TYPE_AXIS(0),
.C_APPLICATION_TYPE_RACH(C_AXI_READ_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_RDCH(0),
.C_APPLICATION_TYPE_WACH(C_AXI_WRITE_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_WDCH(0),
.C_APPLICATION_TYPE_WRCH(0),
.C_AXIS_TDATA_WIDTH(64),
.C_AXIS_TDEST_WIDTH(4),
.C_AXIS_TID_WIDTH(8),
.C_AXIS_TKEEP_WIDTH(4),
.C_AXIS_TSTRB_WIDTH(4),
.C_AXIS_TUSER_WIDTH(4),
.C_AXIS_TYPE(0),
.C_COUNT_TYPE(0),
.C_DATA_COUNT_WIDTH(10),
.C_DEFAULT_VALUE("BlankString"),
.C_DIN_WIDTH(18),
.C_DIN_WIDTH_AXIS(1),
.C_DOUT_RST_VAL("0"),
.C_DOUT_WIDTH(18),
.C_ENABLE_RLOCS(0),
.C_ENABLE_RST_SYNC(1),
.C_ERROR_INJECTION_TYPE(0),
.C_ERROR_INJECTION_TYPE_AXIS(0),
.C_ERROR_INJECTION_TYPE_RACH(0),
.C_ERROR_INJECTION_TYPE_RDCH(0),
.C_ERROR_INJECTION_TYPE_WACH(0),
.C_ERROR_INJECTION_TYPE_WDCH(0),
.C_ERROR_INJECTION_TYPE_WRCH(0),
.C_FAMILY(C_FAMILY),
.C_FULL_FLAGS_RST_VAL(1),
.C_HAS_ALMOST_EMPTY(0),
.C_HAS_ALMOST_FULL(0),
.C_HAS_AXI_RD_CHANNEL(1),
.C_HAS_AXI_WR_CHANNEL(1),
.C_HAS_AXIS_TDATA(0),
.C_HAS_AXIS_TDEST(0),
.C_HAS_AXIS_TID(0),
.C_HAS_AXIS_TKEEP(0),
.C_HAS_AXIS_TLAST(0),
.C_HAS_AXIS_TREADY(1),
.C_HAS_AXIS_TSTRB(0),
.C_HAS_AXIS_TUSER(0),
.C_HAS_BACKUP(0),
.C_HAS_DATA_COUNT(0),
.C_HAS_DATA_COUNTS_AXIS(0),
.C_HAS_DATA_COUNTS_RACH(0),
.C_HAS_DATA_COUNTS_RDCH(0),
.C_HAS_DATA_COUNTS_WACH(0),
.C_HAS_DATA_COUNTS_WDCH(0),
.C_HAS_DATA_COUNTS_WRCH(0),
.C_HAS_INT_CLK(0),
.C_HAS_MASTER_CE(0),
.C_HAS_MEMINIT_FILE(0),
.C_HAS_OVERFLOW(0),
.C_HAS_PROG_FLAGS_AXIS(0),
.C_HAS_PROG_FLAGS_RACH(0),
.C_HAS_PROG_FLAGS_RDCH(0),
.C_HAS_PROG_FLAGS_WACH(0),
.C_HAS_PROG_FLAGS_WDCH(0),
.C_HAS_PROG_FLAGS_WRCH(0),
.C_HAS_RD_DATA_COUNT(0),
.C_HAS_RD_RST(0),
.C_HAS_RST(1),
.C_HAS_SLAVE_CE(0),
.C_HAS_SRST(0),
.C_HAS_UNDERFLOW(0),
.C_HAS_VALID(0),
.C_HAS_WR_ACK(0),
.C_HAS_WR_DATA_COUNT(0),
.C_HAS_WR_RST(0),
.C_IMPLEMENTATION_TYPE(0),
.C_IMPLEMENTATION_TYPE_AXIS(1),
.C_IMPLEMENTATION_TYPE_RACH(2),
.C_IMPLEMENTATION_TYPE_RDCH((C_AXI_READ_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WACH(2),
.C_IMPLEMENTATION_TYPE_WDCH((C_AXI_WRITE_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WRCH(2),
.C_INIT_WR_PNTR_VAL(0),
.C_MEMORY_TYPE(1),
.C_MIF_FILE_NAME("BlankString"),
.C_MSGON_VAL(1),
.C_OPTIMIZATION_MODE(0),
.C_OVERFLOW_LOW(0),
.C_PRELOAD_LATENCY(1),
.C_PRELOAD_REGS(0),
.C_PRIM_FIFO_TYPE(P_PRIM_FIFO_TYPE),
.C_PROG_EMPTY_THRESH_ASSERT_VAL(2),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_AXIS(1022),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WRCH(14),
.C_PROG_EMPTY_THRESH_NEGATE_VAL(3),
.C_PROG_EMPTY_TYPE(0),
.C_PROG_EMPTY_TYPE_AXIS(5),
.C_PROG_EMPTY_TYPE_RACH(5),
.C_PROG_EMPTY_TYPE_RDCH(5),
.C_PROG_EMPTY_TYPE_WACH(5),
.C_PROG_EMPTY_TYPE_WDCH(5),
.C_PROG_EMPTY_TYPE_WRCH(5),
.C_PROG_FULL_THRESH_ASSERT_VAL(1022),
.C_PROG_FULL_THRESH_ASSERT_VAL_AXIS(1023),
.C_PROG_FULL_THRESH_ASSERT_VAL_RACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_RDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_WDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WRCH(15),
.C_PROG_FULL_THRESH_NEGATE_VAL(1021),
.C_PROG_FULL_TYPE(0),
.C_PROG_FULL_TYPE_AXIS(5),
.C_PROG_FULL_TYPE_RACH(5),
.C_PROG_FULL_TYPE_RDCH(5),
.C_PROG_FULL_TYPE_WACH(5),
.C_PROG_FULL_TYPE_WDCH(5),
.C_PROG_FULL_TYPE_WRCH(5),
.C_RD_DATA_COUNT_WIDTH(10),
.C_RD_DEPTH(1024),
.C_RD_FREQ(1),
.C_RD_PNTR_WIDTH(10),
.C_REG_SLICE_MODE_AXIS(0),
.C_REG_SLICE_MODE_RACH(0),
.C_REG_SLICE_MODE_RDCH(0),
.C_REG_SLICE_MODE_WACH(0),
.C_REG_SLICE_MODE_WDCH(0),
.C_REG_SLICE_MODE_WRCH(0),
.C_UNDERFLOW_LOW(0),
.C_USE_COMMON_OVERFLOW(0),
.C_USE_COMMON_UNDERFLOW(0),
.C_USE_DEFAULT_SETTINGS(0),
.C_USE_DOUT_RST(1),
.C_USE_ECC(0),
.C_USE_ECC_AXIS(0),
.C_USE_ECC_RACH(0),
.C_USE_ECC_RDCH(0),
.C_USE_ECC_WACH(0),
.C_USE_ECC_WDCH(0),
.C_USE_ECC_WRCH(0),
.C_USE_EMBEDDED_REG(0),
.C_USE_FIFO16_FLAGS(0),
.C_USE_FWFT_DATA_COUNT(0),
.C_VALID_LOW(0),
.C_WR_ACK_LOW(0),
.C_WR_DATA_COUNT_WIDTH(10),
.C_WR_DEPTH(1024),
.C_WR_DEPTH_AXIS(1024),
.C_WR_DEPTH_RACH(32),
.C_WR_DEPTH_RDCH(C_AXI_READ_FIFO_DEPTH),
.C_WR_DEPTH_WACH(32),
.C_WR_DEPTH_WDCH(C_AXI_WRITE_FIFO_DEPTH),
.C_WR_DEPTH_WRCH(16),
.C_WR_FREQ(1),
.C_WR_PNTR_WIDTH(10),
.C_WR_PNTR_WIDTH_AXIS(10),
.C_WR_PNTR_WIDTH_RACH(5),
.C_WR_PNTR_WIDTH_RDCH((C_AXI_READ_FIFO_DEPTH> 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WACH(5),
.C_WR_PNTR_WIDTH_WDCH((C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WRCH(4),
.C_WR_RESPONSE_LATENCY(1)
)
fifo_gen_inst (
.s_aclk(aclk),
.s_aresetn(aresetn),
.s_axi_awid(s_axi_awid),
.s_axi_awaddr(s_axi_awaddr),
.s_axi_awlen(s_axi_awlen),
.s_axi_awsize(s_axi_awsize),
.s_axi_awburst(s_axi_awburst),
.s_axi_awlock(s_axi_awlock),
.s_axi_awcache(s_axi_awcache),
.s_axi_awprot(s_axi_awprot),
.s_axi_awqos(s_axi_awqos),
.s_axi_awregion(s_axi_awregion_i),
.s_axi_awuser(s_axi_awuser),
.s_axi_awvalid(s_axi_awvalid),
.s_axi_awready(s_axi_awready),
.s_axi_wid(s_axi_wid_i),
.s_axi_wdata(s_axi_wdata),
.s_axi_wstrb(s_axi_wstrb),
.s_axi_wlast(s_axi_wlast),
.s_axi_wvalid(s_axi_wvalid),
.s_axi_wready(s_axi_wready),
.s_axi_bid(s_axi_bid),
.s_axi_bresp(s_axi_bresp),
.s_axi_bvalid(s_axi_bvalid),
.s_axi_bready(s_axi_bready),
.m_axi_awid(m_axi_awid),
.m_axi_awaddr(m_axi_awaddr),
.m_axi_awlen(m_axi_awlen),
.m_axi_awsize(m_axi_awsize),
.m_axi_awburst(m_axi_awburst),
.m_axi_awlock(m_axi_awlock),
.m_axi_awcache(m_axi_awcache),
.m_axi_awprot(m_axi_awprot),
.m_axi_awqos(m_axi_awqos),
.m_axi_awregion(m_axi_awregion_i),
.m_axi_awuser(m_axi_awuser),
.m_axi_awvalid(m_axi_awvalid),
.m_axi_awready(m_axi_awready),
.m_axi_wid(m_axi_wid_i),
.m_axi_wdata(m_axi_wdata),
.m_axi_wstrb(m_axi_wstrb),
.m_axi_wlast(m_axi_wlast),
.m_axi_wvalid(m_axi_wvalid),
.m_axi_wready(m_axi_wready),
.m_axi_bid(m_axi_bid),
.m_axi_bresp(m_axi_bresp),
.m_axi_bvalid(m_axi_bvalid),
.m_axi_bready(m_axi_bready),
.s_axi_arid(s_axi_arid),
.s_axi_araddr(s_axi_araddr),
.s_axi_arlen(s_axi_arlen),
.s_axi_arsize(s_axi_arsize),
.s_axi_arburst(s_axi_arburst),
.s_axi_arlock(s_axi_arlock),
.s_axi_arcache(s_axi_arcache),
.s_axi_arprot(s_axi_arprot),
.s_axi_arqos(s_axi_arqos),
.s_axi_arregion(s_axi_arregion_i),
.s_axi_arvalid(s_axi_arvalid),
.s_axi_arready(s_axi_arready),
.s_axi_rid(s_axi_rid),
.s_axi_rdata(s_axi_rdata),
.s_axi_rresp(s_axi_rresp),
.s_axi_rlast(s_axi_rlast),
.s_axi_rvalid(s_axi_rvalid),
.s_axi_rready(s_axi_rready),
.m_axi_arid(m_axi_arid),
.m_axi_araddr(m_axi_araddr),
.m_axi_arlen(m_axi_arlen),
.m_axi_arsize(m_axi_arsize),
.m_axi_arburst(m_axi_arburst),
.m_axi_arlock(m_axi_arlock),
.m_axi_arcache(m_axi_arcache),
.m_axi_arprot(m_axi_arprot),
.m_axi_arqos(m_axi_arqos),
.m_axi_arregion(m_axi_arregion_i),
.m_axi_arvalid(m_axi_arvalid),
.m_axi_arready(m_axi_arready),
.m_axi_rid(m_axi_rid),
.m_axi_rdata(m_axi_rdata),
.m_axi_rresp(m_axi_rresp),
.m_axi_rlast(m_axi_rlast),
.m_axi_rvalid(m_axi_rvalid),
.m_axi_rready(m_axi_rready),
.m_aclk(aclk),
.m_aclk_en(1'b1),
.s_aclk_en(1'b1),
.s_axi_wuser(s_axi_wuser),
.s_axi_buser(s_axi_buser),
.m_axi_wuser(m_axi_wuser),
.m_axi_buser(m_axi_buser),
.s_axi_aruser(s_axi_aruser),
.s_axi_ruser(s_axi_ruser),
.m_axi_aruser(m_axi_aruser),
.m_axi_ruser(m_axi_ruser),
.almost_empty(),
.almost_full(),
.axis_data_count(),
.axis_dbiterr(),
.axis_injectdbiterr(1'b0),
.axis_injectsbiterr(1'b0),
.axis_overflow(),
.axis_prog_empty(),
.axis_prog_empty_thresh(10'b0),
.axis_prog_full(),
.axis_prog_full_thresh(10'b0),
.axis_rd_data_count(),
.axis_sbiterr(),
.axis_underflow(),
.axis_wr_data_count(),
.axi_ar_data_count(),
.axi_ar_dbiterr(),
.axi_ar_injectdbiterr(1'b0),
.axi_ar_injectsbiterr(1'b0),
.axi_ar_overflow(),
.axi_ar_prog_empty(),
.axi_ar_prog_empty_thresh(5'b0),
.axi_ar_prog_full(),
.axi_ar_prog_full_thresh(5'b0),
.axi_ar_rd_data_count(),
.axi_ar_sbiterr(),
.axi_ar_underflow(),
.axi_ar_wr_data_count(),
.axi_aw_data_count(),
.axi_aw_dbiterr(),
.axi_aw_injectdbiterr(1'b0),
.axi_aw_injectsbiterr(1'b0),
.axi_aw_overflow(),
.axi_aw_prog_empty(),
.axi_aw_prog_empty_thresh(5'b0),
.axi_aw_prog_full(),
.axi_aw_prog_full_thresh(5'b0),
.axi_aw_rd_data_count(),
.axi_aw_sbiterr(),
.axi_aw_underflow(),
.axi_aw_wr_data_count(),
.axi_b_data_count(),
.axi_b_dbiterr(),
.axi_b_injectdbiterr(1'b0),
.axi_b_injectsbiterr(1'b0),
.axi_b_overflow(),
.axi_b_prog_empty(),
.axi_b_prog_empty_thresh(4'b0),
.axi_b_prog_full(),
.axi_b_prog_full_thresh(4'b0),
.axi_b_rd_data_count(),
.axi_b_sbiterr(),
.axi_b_underflow(),
.axi_b_wr_data_count(),
.axi_r_data_count(),
.axi_r_dbiterr(),
.axi_r_injectdbiterr(1'b0),
.axi_r_injectsbiterr(1'b0),
.axi_r_overflow(),
.axi_r_prog_empty(),
.axi_r_prog_empty_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_prog_full(),
.axi_r_prog_full_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_rd_data_count(),
.axi_r_sbiterr(),
.axi_r_underflow(),
.axi_r_wr_data_count(),
.axi_w_data_count(),
.axi_w_dbiterr(),
.axi_w_injectdbiterr(1'b0),
.axi_w_injectsbiterr(1'b0),
.axi_w_overflow(),
.axi_w_prog_empty(),
.axi_w_prog_empty_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_prog_full(),
.axi_w_prog_full_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_rd_data_count(),
.axi_w_sbiterr(),
.axi_w_underflow(),
.axi_w_wr_data_count(),
.backup(1'b0),
.backup_marker(1'b0),
.clk(1'b0),
.data_count(),
.dbiterr(),
.din(18'b0),
.dout(),
.empty(),
.full(),
.injectdbiterr(1'b0),
.injectsbiterr(1'b0),
.int_clk(1'b0),
.m_axis_tdata(),
.m_axis_tdest(),
.m_axis_tid(),
.m_axis_tkeep(),
.m_axis_tlast(),
.m_axis_tready(1'b0),
.m_axis_tstrb(),
.m_axis_tuser(),
.m_axis_tvalid(),
.overflow(),
.prog_empty(),
.prog_empty_thresh(10'b0),
.prog_empty_thresh_assert(10'b0),
.prog_empty_thresh_negate(10'b0),
.prog_full(),
.prog_full_thresh(10'b0),
.prog_full_thresh_assert(10'b0),
.prog_full_thresh_negate(10'b0),
.rd_clk(1'b0),
.rd_data_count(),
.rd_en(1'b0),
.rd_rst(1'b0),
.rst(1'b0),
.sbiterr(),
.srst(1'b0),
.s_axis_tdata(64'b0),
.s_axis_tdest(4'b0),
.s_axis_tid(8'b0),
.s_axis_tkeep(4'b0),
.s_axis_tlast(1'b0),
.s_axis_tready(),
.s_axis_tstrb(4'b0),
.s_axis_tuser(4'b0),
.s_axis_tvalid(1'b0),
.underflow(),
.valid(),
.wr_ack(),
.wr_clk(1'b0),
.wr_data_count(),
.wr_en(1'b0),
.wr_rst(1'b0),
.wr_rst_busy(),
.rd_rst_busy(),
.sleep(1'b0)
);
end
endgenerate
endmodule |
module axi_data_fifo_v2_1_axi_data_fifo #
(
parameter C_FAMILY = "virtex7",
parameter integer C_AXI_PROTOCOL = 0,
parameter integer C_AXI_ID_WIDTH = 4,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_USER_SIGNALS = 0,
parameter integer C_AXI_AWUSER_WIDTH = 1,
parameter integer C_AXI_ARUSER_WIDTH = 1,
parameter integer C_AXI_WUSER_WIDTH = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1,
parameter integer C_AXI_WRITE_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_WRITE_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_WRITE_FIFO_DELAY = 0, // 0 = No, 1 = Yes
// Indicates whether AWVALID and WVALID assertion is delayed until:
// a. the corresponding WLAST is stored in the FIFO, or
// b. no WLAST is stored and the FIFO is full.
// 0 means AW channel is pass-through and
// WVALID is asserted whenever FIFO is not empty.
parameter integer C_AXI_READ_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_READ_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_READ_FIFO_DELAY = 0) // 0 = No, 1 = Yes
// Indicates whether ARVALID assertion is delayed until the
// the remaining vacancy of the FIFO is at least the burst length
// as indicated by ARLEN.
// 0 means AR channel is pass-through.
// System Signals
(input wire aclk,
input wire aresetn,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_awaddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_awlen,
input wire [3-1:0] s_axi_awsize,
input wire [2-1:0] s_axi_awburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_awlock,
input wire [4-1:0] s_axi_awcache,
input wire [3-1:0] s_axi_awprot,
input wire [4-1:0] s_axi_awregion,
input wire [4-1:0] s_axi_awqos,
input wire [C_AXI_AWUSER_WIDTH-1:0] s_axi_awuser,
input wire s_axi_awvalid,
output wire s_axi_awready,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_wid,
input wire [C_AXI_DATA_WIDTH-1:0] s_axi_wdata,
input wire [C_AXI_DATA_WIDTH/8-1:0] s_axi_wstrb,
input wire s_axi_wlast,
input wire [C_AXI_WUSER_WIDTH-1:0] s_axi_wuser,
input wire s_axi_wvalid,
output wire s_axi_wready,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output wire [2-1:0] s_axi_bresp,
output wire [C_AXI_BUSER_WIDTH-1:0] s_axi_buser,
output wire s_axi_bvalid,
input wire s_axi_bready,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_araddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_arlen,
input wire [3-1:0] s_axi_arsize,
input wire [2-1:0] s_axi_arburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_arlock,
input wire [4-1:0] s_axi_arcache,
input wire [3-1:0] s_axi_arprot,
input wire [4-1:0] s_axi_arregion,
input wire [4-1:0] s_axi_arqos,
input wire [C_AXI_ARUSER_WIDTH-1:0] s_axi_aruser,
input wire s_axi_arvalid,
output wire s_axi_arready,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output wire [C_AXI_DATA_WIDTH-1:0] s_axi_rdata,
output wire [2-1:0] s_axi_rresp,
output wire s_axi_rlast,
output wire [C_AXI_RUSER_WIDTH-1:0] s_axi_ruser,
output wire s_axi_rvalid,
input wire s_axi_rready,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_awid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_awaddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_awlen,
output wire [3-1:0] m_axi_awsize,
output wire [2-1:0] m_axi_awburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_awlock,
output wire [4-1:0] m_axi_awcache,
output wire [3-1:0] m_axi_awprot,
output wire [4-1:0] m_axi_awregion,
output wire [4-1:0] m_axi_awqos,
output wire [C_AXI_AWUSER_WIDTH-1:0] m_axi_awuser,
output wire m_axi_awvalid,
input wire m_axi_awready,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] m_axi_wid,
output wire [C_AXI_DATA_WIDTH-1:0] m_axi_wdata,
output wire [C_AXI_DATA_WIDTH/8-1:0] m_axi_wstrb,
output wire m_axi_wlast,
output wire [C_AXI_WUSER_WIDTH-1:0] m_axi_wuser,
output wire m_axi_wvalid,
input wire m_axi_wready,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_bid,
input wire [2-1:0] m_axi_bresp,
input wire [C_AXI_BUSER_WIDTH-1:0] m_axi_buser,
input wire m_axi_bvalid,
output wire m_axi_bready,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_arid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_araddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_arlen,
output wire [3-1:0] m_axi_arsize,
output wire [2-1:0] m_axi_arburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_arlock,
output wire [4-1:0] m_axi_arcache,
output wire [3-1:0] m_axi_arprot,
output wire [4-1:0] m_axi_arregion,
output wire [4-1:0] m_axi_arqos,
output wire [C_AXI_ARUSER_WIDTH-1:0] m_axi_aruser,
output wire m_axi_arvalid,
input wire m_axi_arready,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_rid,
input wire [C_AXI_DATA_WIDTH-1:0] m_axi_rdata,
input wire [2-1:0] m_axi_rresp,
input wire m_axi_rlast,
input wire [C_AXI_RUSER_WIDTH-1:0] m_axi_ruser,
input wire m_axi_rvalid,
output wire m_axi_rready);
localparam integer P_WIDTH_RACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_ARUSER_WIDTH;
localparam integer P_WIDTH_WACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_AWUSER_WIDTH;
localparam integer P_WIDTH_RDCH = 1 + 2 + C_AXI_DATA_WIDTH + C_AXI_ID_WIDTH + C_AXI_RUSER_WIDTH;
localparam integer P_WIDTH_WDCH = 1+C_AXI_DATA_WIDTH+C_AXI_DATA_WIDTH/8+((C_AXI_PROTOCOL==1)?C_AXI_ID_WIDTH:0)+C_AXI_WUSER_WIDTH;
localparam integer P_WIDTH_WRCH = 2 + C_AXI_ID_WIDTH + C_AXI_BUSER_WIDTH;
localparam P_PRIM_FIFO_TYPE = "512x72" ;
localparam integer P_AXI4 = 0;
localparam integer P_AXI3 = 1;
localparam integer P_AXILITE = 2;
localparam integer P_WRITE_FIFO_DEPTH_LOG = (C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1;
localparam integer P_READ_FIFO_DEPTH_LOG = (C_AXI_READ_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1;
// Ceiling of log2(x)
function integer f_ceil_log2
(
input integer x
);
integer acc;
begin
acc=0;
while ((2**acc) < x)
acc = acc + 1;
f_ceil_log2 = acc;
end
endfunction
generate
if (((C_AXI_WRITE_FIFO_DEPTH == 0) && (C_AXI_READ_FIFO_DEPTH == 0)) || (C_AXI_PROTOCOL == P_AXILITE)) begin : gen_bypass
assign m_axi_awid = s_axi_awid;
assign m_axi_awaddr = s_axi_awaddr;
assign m_axi_awlen = s_axi_awlen;
assign m_axi_awsize = s_axi_awsize;
assign m_axi_awburst = s_axi_awburst;
assign m_axi_awlock = s_axi_awlock;
assign m_axi_awcache = s_axi_awcache;
assign m_axi_awprot = s_axi_awprot;
assign m_axi_awregion = s_axi_awregion;
assign m_axi_awqos = s_axi_awqos;
assign m_axi_awuser = s_axi_awuser;
assign m_axi_awvalid = s_axi_awvalid;
assign s_axi_awready = m_axi_awready;
assign m_axi_wid = s_axi_wid;
assign m_axi_wdata = s_axi_wdata;
assign m_axi_wstrb = s_axi_wstrb;
assign m_axi_wlast = s_axi_wlast;
assign m_axi_wuser = s_axi_wuser;
assign m_axi_wvalid = s_axi_wvalid;
assign s_axi_wready = m_axi_wready;
assign s_axi_bid = m_axi_bid;
assign s_axi_bresp = m_axi_bresp;
assign s_axi_buser = m_axi_buser;
assign s_axi_bvalid = m_axi_bvalid;
assign m_axi_bready = s_axi_bready;
assign m_axi_arid = s_axi_arid;
assign m_axi_araddr = s_axi_araddr;
assign m_axi_arlen = s_axi_arlen;
assign m_axi_arsize = s_axi_arsize;
assign m_axi_arburst = s_axi_arburst;
assign m_axi_arlock = s_axi_arlock;
assign m_axi_arcache = s_axi_arcache;
assign m_axi_arprot = s_axi_arprot;
assign m_axi_arregion = s_axi_arregion;
assign m_axi_arqos = s_axi_arqos;
assign m_axi_aruser = s_axi_aruser;
assign m_axi_arvalid = s_axi_arvalid;
assign s_axi_arready = m_axi_arready;
assign s_axi_rid = m_axi_rid;
assign s_axi_rdata = m_axi_rdata;
assign s_axi_rresp = m_axi_rresp;
assign s_axi_rlast = m_axi_rlast;
assign s_axi_ruser = m_axi_ruser;
assign s_axi_rvalid = m_axi_rvalid;
assign m_axi_rready = s_axi_rready;
end else begin : gen_fifo
wire [4-1:0] s_axi_awregion_i;
wire [4-1:0] s_axi_arregion_i;
wire [4-1:0] m_axi_awregion_i;
wire [4-1:0] m_axi_arregion_i;
wire [C_AXI_ID_WIDTH-1:0] s_axi_wid_i;
wire [C_AXI_ID_WIDTH-1:0] m_axi_wid_i;
assign s_axi_awregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_awregion;
assign s_axi_arregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_arregion;
assign m_axi_awregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_awregion_i;
assign m_axi_arregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_arregion_i;
assign s_axi_wid_i = (C_AXI_PROTOCOL == P_AXI3) ? s_axi_wid : {C_AXI_ID_WIDTH{1'b0}};
assign m_axi_wid = (C_AXI_PROTOCOL == P_AXI3) ? m_axi_wid_i : {C_AXI_ID_WIDTH{1'b0}};
fifo_generator_v12_0 #(
.C_INTERFACE_TYPE(2),
.C_AXI_TYPE((C_AXI_PROTOCOL == P_AXI4) ? 1 : 3),
.C_AXI_DATA_WIDTH(C_AXI_DATA_WIDTH),
.C_AXI_ID_WIDTH(C_AXI_ID_WIDTH),
.C_HAS_AXI_ID(1),
.C_AXI_LEN_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 8 : 4),
.C_AXI_LOCK_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 1 : 2),
.C_HAS_AXI_ARUSER(1),
.C_HAS_AXI_AWUSER(1),
.C_HAS_AXI_BUSER(1),
.C_HAS_AXI_RUSER(1),
.C_HAS_AXI_WUSER(1),
.C_AXI_ADDR_WIDTH(C_AXI_ADDR_WIDTH),
.C_AXI_ARUSER_WIDTH(C_AXI_ARUSER_WIDTH),
.C_AXI_AWUSER_WIDTH(C_AXI_AWUSER_WIDTH),
.C_AXI_BUSER_WIDTH(C_AXI_BUSER_WIDTH),
.C_AXI_RUSER_WIDTH(C_AXI_RUSER_WIDTH),
.C_AXI_WUSER_WIDTH(C_AXI_WUSER_WIDTH),
.C_DIN_WIDTH_RACH(P_WIDTH_RACH),
.C_DIN_WIDTH_RDCH(P_WIDTH_RDCH),
.C_DIN_WIDTH_WACH(P_WIDTH_WACH),
.C_DIN_WIDTH_WDCH(P_WIDTH_WDCH),
.C_DIN_WIDTH_WRCH(P_WIDTH_WDCH),
.C_RACH_TYPE(((C_AXI_READ_FIFO_DEPTH != 0) && C_AXI_READ_FIFO_DELAY) ? 0 : 2),
.C_WACH_TYPE(((C_AXI_WRITE_FIFO_DEPTH != 0) && C_AXI_WRITE_FIFO_DELAY) ? 0 : 2),
.C_WDCH_TYPE((C_AXI_WRITE_FIFO_DEPTH != 0) ? 0 : 2),
.C_RDCH_TYPE((C_AXI_READ_FIFO_DEPTH != 0) ? 0 : 2),
.C_WRCH_TYPE(2),
.C_COMMON_CLOCK(1),
.C_ADD_NGC_CONSTRAINT(0),
.C_APPLICATION_TYPE_AXIS(0),
.C_APPLICATION_TYPE_RACH(C_AXI_READ_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_RDCH(0),
.C_APPLICATION_TYPE_WACH(C_AXI_WRITE_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_WDCH(0),
.C_APPLICATION_TYPE_WRCH(0),
.C_AXIS_TDATA_WIDTH(64),
.C_AXIS_TDEST_WIDTH(4),
.C_AXIS_TID_WIDTH(8),
.C_AXIS_TKEEP_WIDTH(4),
.C_AXIS_TSTRB_WIDTH(4),
.C_AXIS_TUSER_WIDTH(4),
.C_AXIS_TYPE(0),
.C_COUNT_TYPE(0),
.C_DATA_COUNT_WIDTH(10),
.C_DEFAULT_VALUE("BlankString"),
.C_DIN_WIDTH(18),
.C_DIN_WIDTH_AXIS(1),
.C_DOUT_RST_VAL("0"),
.C_DOUT_WIDTH(18),
.C_ENABLE_RLOCS(0),
.C_ENABLE_RST_SYNC(1),
.C_ERROR_INJECTION_TYPE(0),
.C_ERROR_INJECTION_TYPE_AXIS(0),
.C_ERROR_INJECTION_TYPE_RACH(0),
.C_ERROR_INJECTION_TYPE_RDCH(0),
.C_ERROR_INJECTION_TYPE_WACH(0),
.C_ERROR_INJECTION_TYPE_WDCH(0),
.C_ERROR_INJECTION_TYPE_WRCH(0),
.C_FAMILY(C_FAMILY),
.C_FULL_FLAGS_RST_VAL(1),
.C_HAS_ALMOST_EMPTY(0),
.C_HAS_ALMOST_FULL(0),
.C_HAS_AXI_RD_CHANNEL(1),
.C_HAS_AXI_WR_CHANNEL(1),
.C_HAS_AXIS_TDATA(0),
.C_HAS_AXIS_TDEST(0),
.C_HAS_AXIS_TID(0),
.C_HAS_AXIS_TKEEP(0),
.C_HAS_AXIS_TLAST(0),
.C_HAS_AXIS_TREADY(1),
.C_HAS_AXIS_TSTRB(0),
.C_HAS_AXIS_TUSER(0),
.C_HAS_BACKUP(0),
.C_HAS_DATA_COUNT(0),
.C_HAS_DATA_COUNTS_AXIS(0),
.C_HAS_DATA_COUNTS_RACH(0),
.C_HAS_DATA_COUNTS_RDCH(0),
.C_HAS_DATA_COUNTS_WACH(0),
.C_HAS_DATA_COUNTS_WDCH(0),
.C_HAS_DATA_COUNTS_WRCH(0),
.C_HAS_INT_CLK(0),
.C_HAS_MASTER_CE(0),
.C_HAS_MEMINIT_FILE(0),
.C_HAS_OVERFLOW(0),
.C_HAS_PROG_FLAGS_AXIS(0),
.C_HAS_PROG_FLAGS_RACH(0),
.C_HAS_PROG_FLAGS_RDCH(0),
.C_HAS_PROG_FLAGS_WACH(0),
.C_HAS_PROG_FLAGS_WDCH(0),
.C_HAS_PROG_FLAGS_WRCH(0),
.C_HAS_RD_DATA_COUNT(0),
.C_HAS_RD_RST(0),
.C_HAS_RST(1),
.C_HAS_SLAVE_CE(0),
.C_HAS_SRST(0),
.C_HAS_UNDERFLOW(0),
.C_HAS_VALID(0),
.C_HAS_WR_ACK(0),
.C_HAS_WR_DATA_COUNT(0),
.C_HAS_WR_RST(0),
.C_IMPLEMENTATION_TYPE(0),
.C_IMPLEMENTATION_TYPE_AXIS(1),
.C_IMPLEMENTATION_TYPE_RACH(2),
.C_IMPLEMENTATION_TYPE_RDCH((C_AXI_READ_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WACH(2),
.C_IMPLEMENTATION_TYPE_WDCH((C_AXI_WRITE_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WRCH(2),
.C_INIT_WR_PNTR_VAL(0),
.C_MEMORY_TYPE(1),
.C_MIF_FILE_NAME("BlankString"),
.C_MSGON_VAL(1),
.C_OPTIMIZATION_MODE(0),
.C_OVERFLOW_LOW(0),
.C_PRELOAD_LATENCY(1),
.C_PRELOAD_REGS(0),
.C_PRIM_FIFO_TYPE(P_PRIM_FIFO_TYPE),
.C_PROG_EMPTY_THRESH_ASSERT_VAL(2),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_AXIS(1022),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WRCH(14),
.C_PROG_EMPTY_THRESH_NEGATE_VAL(3),
.C_PROG_EMPTY_TYPE(0),
.C_PROG_EMPTY_TYPE_AXIS(5),
.C_PROG_EMPTY_TYPE_RACH(5),
.C_PROG_EMPTY_TYPE_RDCH(5),
.C_PROG_EMPTY_TYPE_WACH(5),
.C_PROG_EMPTY_TYPE_WDCH(5),
.C_PROG_EMPTY_TYPE_WRCH(5),
.C_PROG_FULL_THRESH_ASSERT_VAL(1022),
.C_PROG_FULL_THRESH_ASSERT_VAL_AXIS(1023),
.C_PROG_FULL_THRESH_ASSERT_VAL_RACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_RDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_WDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WRCH(15),
.C_PROG_FULL_THRESH_NEGATE_VAL(1021),
.C_PROG_FULL_TYPE(0),
.C_PROG_FULL_TYPE_AXIS(5),
.C_PROG_FULL_TYPE_RACH(5),
.C_PROG_FULL_TYPE_RDCH(5),
.C_PROG_FULL_TYPE_WACH(5),
.C_PROG_FULL_TYPE_WDCH(5),
.C_PROG_FULL_TYPE_WRCH(5),
.C_RD_DATA_COUNT_WIDTH(10),
.C_RD_DEPTH(1024),
.C_RD_FREQ(1),
.C_RD_PNTR_WIDTH(10),
.C_REG_SLICE_MODE_AXIS(0),
.C_REG_SLICE_MODE_RACH(0),
.C_REG_SLICE_MODE_RDCH(0),
.C_REG_SLICE_MODE_WACH(0),
.C_REG_SLICE_MODE_WDCH(0),
.C_REG_SLICE_MODE_WRCH(0),
.C_UNDERFLOW_LOW(0),
.C_USE_COMMON_OVERFLOW(0),
.C_USE_COMMON_UNDERFLOW(0),
.C_USE_DEFAULT_SETTINGS(0),
.C_USE_DOUT_RST(1),
.C_USE_ECC(0),
.C_USE_ECC_AXIS(0),
.C_USE_ECC_RACH(0),
.C_USE_ECC_RDCH(0),
.C_USE_ECC_WACH(0),
.C_USE_ECC_WDCH(0),
.C_USE_ECC_WRCH(0),
.C_USE_EMBEDDED_REG(0),
.C_USE_FIFO16_FLAGS(0),
.C_USE_FWFT_DATA_COUNT(0),
.C_VALID_LOW(0),
.C_WR_ACK_LOW(0),
.C_WR_DATA_COUNT_WIDTH(10),
.C_WR_DEPTH(1024),
.C_WR_DEPTH_AXIS(1024),
.C_WR_DEPTH_RACH(32),
.C_WR_DEPTH_RDCH(C_AXI_READ_FIFO_DEPTH),
.C_WR_DEPTH_WACH(32),
.C_WR_DEPTH_WDCH(C_AXI_WRITE_FIFO_DEPTH),
.C_WR_DEPTH_WRCH(16),
.C_WR_FREQ(1),
.C_WR_PNTR_WIDTH(10),
.C_WR_PNTR_WIDTH_AXIS(10),
.C_WR_PNTR_WIDTH_RACH(5),
.C_WR_PNTR_WIDTH_RDCH((C_AXI_READ_FIFO_DEPTH> 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WACH(5),
.C_WR_PNTR_WIDTH_WDCH((C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WRCH(4),
.C_WR_RESPONSE_LATENCY(1)
)
fifo_gen_inst (
.s_aclk(aclk),
.s_aresetn(aresetn),
.s_axi_awid(s_axi_awid),
.s_axi_awaddr(s_axi_awaddr),
.s_axi_awlen(s_axi_awlen),
.s_axi_awsize(s_axi_awsize),
.s_axi_awburst(s_axi_awburst),
.s_axi_awlock(s_axi_awlock),
.s_axi_awcache(s_axi_awcache),
.s_axi_awprot(s_axi_awprot),
.s_axi_awqos(s_axi_awqos),
.s_axi_awregion(s_axi_awregion_i),
.s_axi_awuser(s_axi_awuser),
.s_axi_awvalid(s_axi_awvalid),
.s_axi_awready(s_axi_awready),
.s_axi_wid(s_axi_wid_i),
.s_axi_wdata(s_axi_wdata),
.s_axi_wstrb(s_axi_wstrb),
.s_axi_wlast(s_axi_wlast),
.s_axi_wvalid(s_axi_wvalid),
.s_axi_wready(s_axi_wready),
.s_axi_bid(s_axi_bid),
.s_axi_bresp(s_axi_bresp),
.s_axi_bvalid(s_axi_bvalid),
.s_axi_bready(s_axi_bready),
.m_axi_awid(m_axi_awid),
.m_axi_awaddr(m_axi_awaddr),
.m_axi_awlen(m_axi_awlen),
.m_axi_awsize(m_axi_awsize),
.m_axi_awburst(m_axi_awburst),
.m_axi_awlock(m_axi_awlock),
.m_axi_awcache(m_axi_awcache),
.m_axi_awprot(m_axi_awprot),
.m_axi_awqos(m_axi_awqos),
.m_axi_awregion(m_axi_awregion_i),
.m_axi_awuser(m_axi_awuser),
.m_axi_awvalid(m_axi_awvalid),
.m_axi_awready(m_axi_awready),
.m_axi_wid(m_axi_wid_i),
.m_axi_wdata(m_axi_wdata),
.m_axi_wstrb(m_axi_wstrb),
.m_axi_wlast(m_axi_wlast),
.m_axi_wvalid(m_axi_wvalid),
.m_axi_wready(m_axi_wready),
.m_axi_bid(m_axi_bid),
.m_axi_bresp(m_axi_bresp),
.m_axi_bvalid(m_axi_bvalid),
.m_axi_bready(m_axi_bready),
.s_axi_arid(s_axi_arid),
.s_axi_araddr(s_axi_araddr),
.s_axi_arlen(s_axi_arlen),
.s_axi_arsize(s_axi_arsize),
.s_axi_arburst(s_axi_arburst),
.s_axi_arlock(s_axi_arlock),
.s_axi_arcache(s_axi_arcache),
.s_axi_arprot(s_axi_arprot),
.s_axi_arqos(s_axi_arqos),
.s_axi_arregion(s_axi_arregion_i),
.s_axi_arvalid(s_axi_arvalid),
.s_axi_arready(s_axi_arready),
.s_axi_rid(s_axi_rid),
.s_axi_rdata(s_axi_rdata),
.s_axi_rresp(s_axi_rresp),
.s_axi_rlast(s_axi_rlast),
.s_axi_rvalid(s_axi_rvalid),
.s_axi_rready(s_axi_rready),
.m_axi_arid(m_axi_arid),
.m_axi_araddr(m_axi_araddr),
.m_axi_arlen(m_axi_arlen),
.m_axi_arsize(m_axi_arsize),
.m_axi_arburst(m_axi_arburst),
.m_axi_arlock(m_axi_arlock),
.m_axi_arcache(m_axi_arcache),
.m_axi_arprot(m_axi_arprot),
.m_axi_arqos(m_axi_arqos),
.m_axi_arregion(m_axi_arregion_i),
.m_axi_arvalid(m_axi_arvalid),
.m_axi_arready(m_axi_arready),
.m_axi_rid(m_axi_rid),
.m_axi_rdata(m_axi_rdata),
.m_axi_rresp(m_axi_rresp),
.m_axi_rlast(m_axi_rlast),
.m_axi_rvalid(m_axi_rvalid),
.m_axi_rready(m_axi_rready),
.m_aclk(aclk),
.m_aclk_en(1'b1),
.s_aclk_en(1'b1),
.s_axi_wuser(s_axi_wuser),
.s_axi_buser(s_axi_buser),
.m_axi_wuser(m_axi_wuser),
.m_axi_buser(m_axi_buser),
.s_axi_aruser(s_axi_aruser),
.s_axi_ruser(s_axi_ruser),
.m_axi_aruser(m_axi_aruser),
.m_axi_ruser(m_axi_ruser),
.almost_empty(),
.almost_full(),
.axis_data_count(),
.axis_dbiterr(),
.axis_injectdbiterr(1'b0),
.axis_injectsbiterr(1'b0),
.axis_overflow(),
.axis_prog_empty(),
.axis_prog_empty_thresh(10'b0),
.axis_prog_full(),
.axis_prog_full_thresh(10'b0),
.axis_rd_data_count(),
.axis_sbiterr(),
.axis_underflow(),
.axis_wr_data_count(),
.axi_ar_data_count(),
.axi_ar_dbiterr(),
.axi_ar_injectdbiterr(1'b0),
.axi_ar_injectsbiterr(1'b0),
.axi_ar_overflow(),
.axi_ar_prog_empty(),
.axi_ar_prog_empty_thresh(5'b0),
.axi_ar_prog_full(),
.axi_ar_prog_full_thresh(5'b0),
.axi_ar_rd_data_count(),
.axi_ar_sbiterr(),
.axi_ar_underflow(),
.axi_ar_wr_data_count(),
.axi_aw_data_count(),
.axi_aw_dbiterr(),
.axi_aw_injectdbiterr(1'b0),
.axi_aw_injectsbiterr(1'b0),
.axi_aw_overflow(),
.axi_aw_prog_empty(),
.axi_aw_prog_empty_thresh(5'b0),
.axi_aw_prog_full(),
.axi_aw_prog_full_thresh(5'b0),
.axi_aw_rd_data_count(),
.axi_aw_sbiterr(),
.axi_aw_underflow(),
.axi_aw_wr_data_count(),
.axi_b_data_count(),
.axi_b_dbiterr(),
.axi_b_injectdbiterr(1'b0),
.axi_b_injectsbiterr(1'b0),
.axi_b_overflow(),
.axi_b_prog_empty(),
.axi_b_prog_empty_thresh(4'b0),
.axi_b_prog_full(),
.axi_b_prog_full_thresh(4'b0),
.axi_b_rd_data_count(),
.axi_b_sbiterr(),
.axi_b_underflow(),
.axi_b_wr_data_count(),
.axi_r_data_count(),
.axi_r_dbiterr(),
.axi_r_injectdbiterr(1'b0),
.axi_r_injectsbiterr(1'b0),
.axi_r_overflow(),
.axi_r_prog_empty(),
.axi_r_prog_empty_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_prog_full(),
.axi_r_prog_full_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_rd_data_count(),
.axi_r_sbiterr(),
.axi_r_underflow(),
.axi_r_wr_data_count(),
.axi_w_data_count(),
.axi_w_dbiterr(),
.axi_w_injectdbiterr(1'b0),
.axi_w_injectsbiterr(1'b0),
.axi_w_overflow(),
.axi_w_prog_empty(),
.axi_w_prog_empty_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_prog_full(),
.axi_w_prog_full_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_rd_data_count(),
.axi_w_sbiterr(),
.axi_w_underflow(),
.axi_w_wr_data_count(),
.backup(1'b0),
.backup_marker(1'b0),
.clk(1'b0),
.data_count(),
.dbiterr(),
.din(18'b0),
.dout(),
.empty(),
.full(),
.injectdbiterr(1'b0),
.injectsbiterr(1'b0),
.int_clk(1'b0),
.m_axis_tdata(),
.m_axis_tdest(),
.m_axis_tid(),
.m_axis_tkeep(),
.m_axis_tlast(),
.m_axis_tready(1'b0),
.m_axis_tstrb(),
.m_axis_tuser(),
.m_axis_tvalid(),
.overflow(),
.prog_empty(),
.prog_empty_thresh(10'b0),
.prog_empty_thresh_assert(10'b0),
.prog_empty_thresh_negate(10'b0),
.prog_full(),
.prog_full_thresh(10'b0),
.prog_full_thresh_assert(10'b0),
.prog_full_thresh_negate(10'b0),
.rd_clk(1'b0),
.rd_data_count(),
.rd_en(1'b0),
.rd_rst(1'b0),
.rst(1'b0),
.sbiterr(),
.srst(1'b0),
.s_axis_tdata(64'b0),
.s_axis_tdest(4'b0),
.s_axis_tid(8'b0),
.s_axis_tkeep(4'b0),
.s_axis_tlast(1'b0),
.s_axis_tready(),
.s_axis_tstrb(4'b0),
.s_axis_tuser(4'b0),
.s_axis_tvalid(1'b0),
.underflow(),
.valid(),
.wr_ack(),
.wr_clk(1'b0),
.wr_data_count(),
.wr_en(1'b0),
.wr_rst(1'b0),
.wr_rst_busy(),
.rd_rst_busy(),
.sleep(1'b0)
);
end
endgenerate
endmodule |
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule |
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule |
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule |
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule |
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule |
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule |
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule |
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule |
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule |
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule |
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule |
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule |
module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule |
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule |
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule |
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule |
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule |
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule |
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule |
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule |
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule |
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule |
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule |
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule |
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule |
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule |
module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule |
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule |
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule |
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule |
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule |
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule |