text
stringlengths 938
1.05M
|
|---|
/*
* VGA top level file
* Copyright (C) 2010 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module vga (
// Wishbone signals
input wb_clk_i, // 25 Mhz VDU clock
input wb_rst_i,
input [15:0] wb_dat_i,
output [15:0] wb_dat_o,
input [16:1] wb_adr_i,
input wb_we_i,
input wb_tga_i,
input [ 1:0] wb_sel_i,
input wb_stb_i,
input wb_cyc_i,
output wb_ack_o,
// VGA pad signals
output [ 3:0] vga_red_o,
output [ 3:0] vga_green_o,
output [ 3:0] vga_blue_o,
output horiz_sync,
output vert_sync,
// CSR SRAM master interface
output [17:1] csrm_adr_o,
output [ 1:0] csrm_sel_o,
output csrm_we_o,
output [15:0] csrm_dat_o,
input [15:0] csrm_dat_i
);
// Registers and nets
//
// csr address
reg [17:1] csr_adr_i;
reg csr_stb_i;
// Config wires
wire [15:0] conf_wb_dat_o;
wire conf_wb_ack_o;
// Mem wires
wire [15:0] mem_wb_dat_o;
wire mem_wb_ack_o;
// LCD wires
wire [17:1] csr_adr_o;
wire [15:0] csr_dat_i;
wire csr_stb_o;
wire v_retrace;
wire vh_retrace;
wire w_vert_sync;
// VGA configuration registers
wire shift_reg1;
wire graphics_alpha;
wire memory_mapping1;
wire [ 1:0] write_mode;
wire [ 1:0] raster_op;
wire read_mode;
wire [ 7:0] bitmask;
wire [ 3:0] set_reset;
wire [ 3:0] enable_set_reset;
wire [ 3:0] map_mask;
wire x_dotclockdiv2;
wire chain_four;
wire [ 1:0] read_map_select;
wire [ 3:0] color_compare;
wire [ 3:0] color_dont_care;
// Wishbone master to SRAM
wire [17:1] wbm_adr_o;
wire [ 1:0] wbm_sel_o;
wire wbm_we_o;
wire [15:0] wbm_dat_o;
wire [15:0] wbm_dat_i;
wire wbm_stb_o;
wire wbm_ack_i;
wire stb;
// CRT wires
wire [ 5:0] cur_start;
wire [ 5:0] cur_end;
wire [15:0] start_addr;
wire [ 4:0] vcursor;
wire [ 6:0] hcursor;
wire [ 6:0] horiz_total;
wire [ 6:0] end_horiz;
wire [ 6:0] st_hor_retr;
wire [ 4:0] end_hor_retr;
wire [ 9:0] vert_total;
wire [ 9:0] end_vert;
wire [ 9:0] st_ver_retr;
wire [ 3:0] end_ver_retr;
// attribute_ctrl wires
wire [3:0] pal_addr;
wire pal_we;
wire [7:0] pal_read;
wire [7:0] pal_write;
// dac_regs wires
wire dac_we;
wire [1:0] dac_read_data_cycle;
wire [7:0] dac_read_data_register;
wire [3:0] dac_read_data;
wire [1:0] dac_write_data_cycle;
wire [7:0] dac_write_data_register;
wire [3:0] dac_write_data;
// Module instances
//
vga_config_iface config_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wb_dat_i (wb_dat_i),
.wb_dat_o (conf_wb_dat_o),
.wb_adr_i (wb_adr_i[4:1]),
.wb_we_i (wb_we_i),
.wb_sel_i (wb_sel_i),
.wb_stb_i (stb & wb_tga_i),
.wb_ack_o (conf_wb_ack_o),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.x_dotclockdiv2 (x_dotclockdiv2),
.chain_four (chain_four),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.cur_start (cur_start),
.cur_end (cur_end),
.start_addr (start_addr),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_lcd lcd (
.clk (wb_clk_i),
.rst (wb_rst_i),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.csr_adr_o (csr_adr_o),
.csr_dat_i (csr_dat_i),
.csr_stb_o (csr_stb_o),
.vga_red_o (vga_red_o),
.vga_green_o (vga_green_o),
.vga_blue_o (vga_blue_o),
.horiz_sync (horiz_sync),
.vert_sync (w_vert_sync),
.cur_start (cur_start),
.cur_end (cur_end),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.x_dotclockdiv2 (x_dotclockdiv2),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_cpu_mem_iface cpu_mem_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wbs_adr_i (wb_adr_i),
.wbs_sel_i (wb_sel_i),
.wbs_we_i (wb_we_i),
.wbs_dat_i (wb_dat_i),
.wbs_dat_o (mem_wb_dat_o),
.wbs_stb_i (stb & !wb_tga_i),
.wbs_ack_o (mem_wb_ack_o),
.wbm_adr_o (wbm_adr_o),
.wbm_sel_o (wbm_sel_o),
.wbm_we_o (wbm_we_o),
.wbm_dat_o (wbm_dat_o),
.wbm_dat_i (wbm_dat_i),
.wbm_stb_o (wbm_stb_o),
.wbm_ack_i (wbm_ack_i),
.chain_four (chain_four),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care)
);
vga_mem_arbitrer mem_arbitrer (
.clk_i (wb_clk_i),
.rst_i (wb_rst_i),
.wb_adr_i (wbm_adr_o),
.wb_sel_i (wbm_sel_o),
.wb_we_i (wbm_we_o),
.wb_dat_i (wbm_dat_o),
.wb_dat_o (wbm_dat_i),
.wb_stb_i (wbm_stb_o),
.wb_ack_o (wbm_ack_i),
.csr_adr_i (csr_adr_i),
.csr_dat_o (csr_dat_i),
.csr_stb_i (csr_stb_i),
.csrm_adr_o (csrm_adr_o),
.csrm_sel_o (csrm_sel_o),
.csrm_we_o (csrm_we_o),
.csrm_dat_o (csrm_dat_o),
.csrm_dat_i (csrm_dat_i)
);
// Continous assignments
assign wb_dat_o = wb_tga_i ? conf_wb_dat_o : mem_wb_dat_o;
assign wb_ack_o = wb_tga_i ? conf_wb_ack_o : mem_wb_ack_o;
assign stb = wb_stb_i & wb_cyc_i;
assign vert_sync = ~graphics_alpha ^ w_vert_sync;
// Behaviour
// csr_adr_i
always @(posedge wb_clk_i)
csr_adr_i <= wb_rst_i ? 17'h0 : csr_adr_o + start_addr[15:1];
// csr_stb_i
always @(posedge wb_clk_i)
csr_stb_i <= wb_rst_i ? 1'b0 : csr_stb_o;
endmodule
|
/*
* VGA top level file
* Copyright (C) 2010 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module vga (
// Wishbone signals
input wb_clk_i, // 25 Mhz VDU clock
input wb_rst_i,
input [15:0] wb_dat_i,
output [15:0] wb_dat_o,
input [16:1] wb_adr_i,
input wb_we_i,
input wb_tga_i,
input [ 1:0] wb_sel_i,
input wb_stb_i,
input wb_cyc_i,
output wb_ack_o,
// VGA pad signals
output [ 3:0] vga_red_o,
output [ 3:0] vga_green_o,
output [ 3:0] vga_blue_o,
output horiz_sync,
output vert_sync,
// CSR SRAM master interface
output [17:1] csrm_adr_o,
output [ 1:0] csrm_sel_o,
output csrm_we_o,
output [15:0] csrm_dat_o,
input [15:0] csrm_dat_i
);
// Registers and nets
//
// csr address
reg [17:1] csr_adr_i;
reg csr_stb_i;
// Config wires
wire [15:0] conf_wb_dat_o;
wire conf_wb_ack_o;
// Mem wires
wire [15:0] mem_wb_dat_o;
wire mem_wb_ack_o;
// LCD wires
wire [17:1] csr_adr_o;
wire [15:0] csr_dat_i;
wire csr_stb_o;
wire v_retrace;
wire vh_retrace;
wire w_vert_sync;
// VGA configuration registers
wire shift_reg1;
wire graphics_alpha;
wire memory_mapping1;
wire [ 1:0] write_mode;
wire [ 1:0] raster_op;
wire read_mode;
wire [ 7:0] bitmask;
wire [ 3:0] set_reset;
wire [ 3:0] enable_set_reset;
wire [ 3:0] map_mask;
wire x_dotclockdiv2;
wire chain_four;
wire [ 1:0] read_map_select;
wire [ 3:0] color_compare;
wire [ 3:0] color_dont_care;
// Wishbone master to SRAM
wire [17:1] wbm_adr_o;
wire [ 1:0] wbm_sel_o;
wire wbm_we_o;
wire [15:0] wbm_dat_o;
wire [15:0] wbm_dat_i;
wire wbm_stb_o;
wire wbm_ack_i;
wire stb;
// CRT wires
wire [ 5:0] cur_start;
wire [ 5:0] cur_end;
wire [15:0] start_addr;
wire [ 4:0] vcursor;
wire [ 6:0] hcursor;
wire [ 6:0] horiz_total;
wire [ 6:0] end_horiz;
wire [ 6:0] st_hor_retr;
wire [ 4:0] end_hor_retr;
wire [ 9:0] vert_total;
wire [ 9:0] end_vert;
wire [ 9:0] st_ver_retr;
wire [ 3:0] end_ver_retr;
// attribute_ctrl wires
wire [3:0] pal_addr;
wire pal_we;
wire [7:0] pal_read;
wire [7:0] pal_write;
// dac_regs wires
wire dac_we;
wire [1:0] dac_read_data_cycle;
wire [7:0] dac_read_data_register;
wire [3:0] dac_read_data;
wire [1:0] dac_write_data_cycle;
wire [7:0] dac_write_data_register;
wire [3:0] dac_write_data;
// Module instances
//
vga_config_iface config_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wb_dat_i (wb_dat_i),
.wb_dat_o (conf_wb_dat_o),
.wb_adr_i (wb_adr_i[4:1]),
.wb_we_i (wb_we_i),
.wb_sel_i (wb_sel_i),
.wb_stb_i (stb & wb_tga_i),
.wb_ack_o (conf_wb_ack_o),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.x_dotclockdiv2 (x_dotclockdiv2),
.chain_four (chain_four),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.cur_start (cur_start),
.cur_end (cur_end),
.start_addr (start_addr),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_lcd lcd (
.clk (wb_clk_i),
.rst (wb_rst_i),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.csr_adr_o (csr_adr_o),
.csr_dat_i (csr_dat_i),
.csr_stb_o (csr_stb_o),
.vga_red_o (vga_red_o),
.vga_green_o (vga_green_o),
.vga_blue_o (vga_blue_o),
.horiz_sync (horiz_sync),
.vert_sync (w_vert_sync),
.cur_start (cur_start),
.cur_end (cur_end),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.x_dotclockdiv2 (x_dotclockdiv2),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_cpu_mem_iface cpu_mem_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wbs_adr_i (wb_adr_i),
.wbs_sel_i (wb_sel_i),
.wbs_we_i (wb_we_i),
.wbs_dat_i (wb_dat_i),
.wbs_dat_o (mem_wb_dat_o),
.wbs_stb_i (stb & !wb_tga_i),
.wbs_ack_o (mem_wb_ack_o),
.wbm_adr_o (wbm_adr_o),
.wbm_sel_o (wbm_sel_o),
.wbm_we_o (wbm_we_o),
.wbm_dat_o (wbm_dat_o),
.wbm_dat_i (wbm_dat_i),
.wbm_stb_o (wbm_stb_o),
.wbm_ack_i (wbm_ack_i),
.chain_four (chain_four),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care)
);
vga_mem_arbitrer mem_arbitrer (
.clk_i (wb_clk_i),
.rst_i (wb_rst_i),
.wb_adr_i (wbm_adr_o),
.wb_sel_i (wbm_sel_o),
.wb_we_i (wbm_we_o),
.wb_dat_i (wbm_dat_o),
.wb_dat_o (wbm_dat_i),
.wb_stb_i (wbm_stb_o),
.wb_ack_o (wbm_ack_i),
.csr_adr_i (csr_adr_i),
.csr_dat_o (csr_dat_i),
.csr_stb_i (csr_stb_i),
.csrm_adr_o (csrm_adr_o),
.csrm_sel_o (csrm_sel_o),
.csrm_we_o (csrm_we_o),
.csrm_dat_o (csrm_dat_o),
.csrm_dat_i (csrm_dat_i)
);
// Continous assignments
assign wb_dat_o = wb_tga_i ? conf_wb_dat_o : mem_wb_dat_o;
assign wb_ack_o = wb_tga_i ? conf_wb_ack_o : mem_wb_ack_o;
assign stb = wb_stb_i & wb_cyc_i;
assign vert_sync = ~graphics_alpha ^ w_vert_sync;
// Behaviour
// csr_adr_i
always @(posedge wb_clk_i)
csr_adr_i <= wb_rst_i ? 17'h0 : csr_adr_o + start_addr[15:1];
// csr_stb_i
always @(posedge wb_clk_i)
csr_stb_i <= wb_rst_i ? 1'b0 : csr_stb_o;
endmodule
|
/*
* VGA top level file
* Copyright (C) 2010 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module vga (
// Wishbone signals
input wb_clk_i, // 25 Mhz VDU clock
input wb_rst_i,
input [15:0] wb_dat_i,
output [15:0] wb_dat_o,
input [16:1] wb_adr_i,
input wb_we_i,
input wb_tga_i,
input [ 1:0] wb_sel_i,
input wb_stb_i,
input wb_cyc_i,
output wb_ack_o,
// VGA pad signals
output [ 3:0] vga_red_o,
output [ 3:0] vga_green_o,
output [ 3:0] vga_blue_o,
output horiz_sync,
output vert_sync,
// CSR SRAM master interface
output [17:1] csrm_adr_o,
output [ 1:0] csrm_sel_o,
output csrm_we_o,
output [15:0] csrm_dat_o,
input [15:0] csrm_dat_i
);
// Registers and nets
//
// csr address
reg [17:1] csr_adr_i;
reg csr_stb_i;
// Config wires
wire [15:0] conf_wb_dat_o;
wire conf_wb_ack_o;
// Mem wires
wire [15:0] mem_wb_dat_o;
wire mem_wb_ack_o;
// LCD wires
wire [17:1] csr_adr_o;
wire [15:0] csr_dat_i;
wire csr_stb_o;
wire v_retrace;
wire vh_retrace;
wire w_vert_sync;
// VGA configuration registers
wire shift_reg1;
wire graphics_alpha;
wire memory_mapping1;
wire [ 1:0] write_mode;
wire [ 1:0] raster_op;
wire read_mode;
wire [ 7:0] bitmask;
wire [ 3:0] set_reset;
wire [ 3:0] enable_set_reset;
wire [ 3:0] map_mask;
wire x_dotclockdiv2;
wire chain_four;
wire [ 1:0] read_map_select;
wire [ 3:0] color_compare;
wire [ 3:0] color_dont_care;
// Wishbone master to SRAM
wire [17:1] wbm_adr_o;
wire [ 1:0] wbm_sel_o;
wire wbm_we_o;
wire [15:0] wbm_dat_o;
wire [15:0] wbm_dat_i;
wire wbm_stb_o;
wire wbm_ack_i;
wire stb;
// CRT wires
wire [ 5:0] cur_start;
wire [ 5:0] cur_end;
wire [15:0] start_addr;
wire [ 4:0] vcursor;
wire [ 6:0] hcursor;
wire [ 6:0] horiz_total;
wire [ 6:0] end_horiz;
wire [ 6:0] st_hor_retr;
wire [ 4:0] end_hor_retr;
wire [ 9:0] vert_total;
wire [ 9:0] end_vert;
wire [ 9:0] st_ver_retr;
wire [ 3:0] end_ver_retr;
// attribute_ctrl wires
wire [3:0] pal_addr;
wire pal_we;
wire [7:0] pal_read;
wire [7:0] pal_write;
// dac_regs wires
wire dac_we;
wire [1:0] dac_read_data_cycle;
wire [7:0] dac_read_data_register;
wire [3:0] dac_read_data;
wire [1:0] dac_write_data_cycle;
wire [7:0] dac_write_data_register;
wire [3:0] dac_write_data;
// Module instances
//
vga_config_iface config_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wb_dat_i (wb_dat_i),
.wb_dat_o (conf_wb_dat_o),
.wb_adr_i (wb_adr_i[4:1]),
.wb_we_i (wb_we_i),
.wb_sel_i (wb_sel_i),
.wb_stb_i (stb & wb_tga_i),
.wb_ack_o (conf_wb_ack_o),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.x_dotclockdiv2 (x_dotclockdiv2),
.chain_four (chain_four),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.cur_start (cur_start),
.cur_end (cur_end),
.start_addr (start_addr),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_lcd lcd (
.clk (wb_clk_i),
.rst (wb_rst_i),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.csr_adr_o (csr_adr_o),
.csr_dat_i (csr_dat_i),
.csr_stb_o (csr_stb_o),
.vga_red_o (vga_red_o),
.vga_green_o (vga_green_o),
.vga_blue_o (vga_blue_o),
.horiz_sync (horiz_sync),
.vert_sync (w_vert_sync),
.cur_start (cur_start),
.cur_end (cur_end),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.x_dotclockdiv2 (x_dotclockdiv2),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_cpu_mem_iface cpu_mem_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wbs_adr_i (wb_adr_i),
.wbs_sel_i (wb_sel_i),
.wbs_we_i (wb_we_i),
.wbs_dat_i (wb_dat_i),
.wbs_dat_o (mem_wb_dat_o),
.wbs_stb_i (stb & !wb_tga_i),
.wbs_ack_o (mem_wb_ack_o),
.wbm_adr_o (wbm_adr_o),
.wbm_sel_o (wbm_sel_o),
.wbm_we_o (wbm_we_o),
.wbm_dat_o (wbm_dat_o),
.wbm_dat_i (wbm_dat_i),
.wbm_stb_o (wbm_stb_o),
.wbm_ack_i (wbm_ack_i),
.chain_four (chain_four),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care)
);
vga_mem_arbitrer mem_arbitrer (
.clk_i (wb_clk_i),
.rst_i (wb_rst_i),
.wb_adr_i (wbm_adr_o),
.wb_sel_i (wbm_sel_o),
.wb_we_i (wbm_we_o),
.wb_dat_i (wbm_dat_o),
.wb_dat_o (wbm_dat_i),
.wb_stb_i (wbm_stb_o),
.wb_ack_o (wbm_ack_i),
.csr_adr_i (csr_adr_i),
.csr_dat_o (csr_dat_i),
.csr_stb_i (csr_stb_i),
.csrm_adr_o (csrm_adr_o),
.csrm_sel_o (csrm_sel_o),
.csrm_we_o (csrm_we_o),
.csrm_dat_o (csrm_dat_o),
.csrm_dat_i (csrm_dat_i)
);
// Continous assignments
assign wb_dat_o = wb_tga_i ? conf_wb_dat_o : mem_wb_dat_o;
assign wb_ack_o = wb_tga_i ? conf_wb_ack_o : mem_wb_ack_o;
assign stb = wb_stb_i & wb_cyc_i;
assign vert_sync = ~graphics_alpha ^ w_vert_sync;
// Behaviour
// csr_adr_i
always @(posedge wb_clk_i)
csr_adr_i <= wb_rst_i ? 17'h0 : csr_adr_o + start_addr[15:1];
// csr_stb_i
always @(posedge wb_clk_i)
csr_stb_i <= wb_rst_i ? 1'b0 : csr_stb_o;
endmodule
|
/*
* VGA top level file
* Copyright (C) 2010 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module vga (
// Wishbone signals
input wb_clk_i, // 25 Mhz VDU clock
input wb_rst_i,
input [15:0] wb_dat_i,
output [15:0] wb_dat_o,
input [16:1] wb_adr_i,
input wb_we_i,
input wb_tga_i,
input [ 1:0] wb_sel_i,
input wb_stb_i,
input wb_cyc_i,
output wb_ack_o,
// VGA pad signals
output [ 3:0] vga_red_o,
output [ 3:0] vga_green_o,
output [ 3:0] vga_blue_o,
output horiz_sync,
output vert_sync,
// CSR SRAM master interface
output [17:1] csrm_adr_o,
output [ 1:0] csrm_sel_o,
output csrm_we_o,
output [15:0] csrm_dat_o,
input [15:0] csrm_dat_i
);
// Registers and nets
//
// csr address
reg [17:1] csr_adr_i;
reg csr_stb_i;
// Config wires
wire [15:0] conf_wb_dat_o;
wire conf_wb_ack_o;
// Mem wires
wire [15:0] mem_wb_dat_o;
wire mem_wb_ack_o;
// LCD wires
wire [17:1] csr_adr_o;
wire [15:0] csr_dat_i;
wire csr_stb_o;
wire v_retrace;
wire vh_retrace;
wire w_vert_sync;
// VGA configuration registers
wire shift_reg1;
wire graphics_alpha;
wire memory_mapping1;
wire [ 1:0] write_mode;
wire [ 1:0] raster_op;
wire read_mode;
wire [ 7:0] bitmask;
wire [ 3:0] set_reset;
wire [ 3:0] enable_set_reset;
wire [ 3:0] map_mask;
wire x_dotclockdiv2;
wire chain_four;
wire [ 1:0] read_map_select;
wire [ 3:0] color_compare;
wire [ 3:0] color_dont_care;
// Wishbone master to SRAM
wire [17:1] wbm_adr_o;
wire [ 1:0] wbm_sel_o;
wire wbm_we_o;
wire [15:0] wbm_dat_o;
wire [15:0] wbm_dat_i;
wire wbm_stb_o;
wire wbm_ack_i;
wire stb;
// CRT wires
wire [ 5:0] cur_start;
wire [ 5:0] cur_end;
wire [15:0] start_addr;
wire [ 4:0] vcursor;
wire [ 6:0] hcursor;
wire [ 6:0] horiz_total;
wire [ 6:0] end_horiz;
wire [ 6:0] st_hor_retr;
wire [ 4:0] end_hor_retr;
wire [ 9:0] vert_total;
wire [ 9:0] end_vert;
wire [ 9:0] st_ver_retr;
wire [ 3:0] end_ver_retr;
// attribute_ctrl wires
wire [3:0] pal_addr;
wire pal_we;
wire [7:0] pal_read;
wire [7:0] pal_write;
// dac_regs wires
wire dac_we;
wire [1:0] dac_read_data_cycle;
wire [7:0] dac_read_data_register;
wire [3:0] dac_read_data;
wire [1:0] dac_write_data_cycle;
wire [7:0] dac_write_data_register;
wire [3:0] dac_write_data;
// Module instances
//
vga_config_iface config_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wb_dat_i (wb_dat_i),
.wb_dat_o (conf_wb_dat_o),
.wb_adr_i (wb_adr_i[4:1]),
.wb_we_i (wb_we_i),
.wb_sel_i (wb_sel_i),
.wb_stb_i (stb & wb_tga_i),
.wb_ack_o (conf_wb_ack_o),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.x_dotclockdiv2 (x_dotclockdiv2),
.chain_four (chain_four),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.cur_start (cur_start),
.cur_end (cur_end),
.start_addr (start_addr),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_lcd lcd (
.clk (wb_clk_i),
.rst (wb_rst_i),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.csr_adr_o (csr_adr_o),
.csr_dat_i (csr_dat_i),
.csr_stb_o (csr_stb_o),
.vga_red_o (vga_red_o),
.vga_green_o (vga_green_o),
.vga_blue_o (vga_blue_o),
.horiz_sync (horiz_sync),
.vert_sync (w_vert_sync),
.cur_start (cur_start),
.cur_end (cur_end),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.x_dotclockdiv2 (x_dotclockdiv2),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_cpu_mem_iface cpu_mem_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wbs_adr_i (wb_adr_i),
.wbs_sel_i (wb_sel_i),
.wbs_we_i (wb_we_i),
.wbs_dat_i (wb_dat_i),
.wbs_dat_o (mem_wb_dat_o),
.wbs_stb_i (stb & !wb_tga_i),
.wbs_ack_o (mem_wb_ack_o),
.wbm_adr_o (wbm_adr_o),
.wbm_sel_o (wbm_sel_o),
.wbm_we_o (wbm_we_o),
.wbm_dat_o (wbm_dat_o),
.wbm_dat_i (wbm_dat_i),
.wbm_stb_o (wbm_stb_o),
.wbm_ack_i (wbm_ack_i),
.chain_four (chain_four),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care)
);
vga_mem_arbitrer mem_arbitrer (
.clk_i (wb_clk_i),
.rst_i (wb_rst_i),
.wb_adr_i (wbm_adr_o),
.wb_sel_i (wbm_sel_o),
.wb_we_i (wbm_we_o),
.wb_dat_i (wbm_dat_o),
.wb_dat_o (wbm_dat_i),
.wb_stb_i (wbm_stb_o),
.wb_ack_o (wbm_ack_i),
.csr_adr_i (csr_adr_i),
.csr_dat_o (csr_dat_i),
.csr_stb_i (csr_stb_i),
.csrm_adr_o (csrm_adr_o),
.csrm_sel_o (csrm_sel_o),
.csrm_we_o (csrm_we_o),
.csrm_dat_o (csrm_dat_o),
.csrm_dat_i (csrm_dat_i)
);
// Continous assignments
assign wb_dat_o = wb_tga_i ? conf_wb_dat_o : mem_wb_dat_o;
assign wb_ack_o = wb_tga_i ? conf_wb_ack_o : mem_wb_ack_o;
assign stb = wb_stb_i & wb_cyc_i;
assign vert_sync = ~graphics_alpha ^ w_vert_sync;
// Behaviour
// csr_adr_i
always @(posedge wb_clk_i)
csr_adr_i <= wb_rst_i ? 17'h0 : csr_adr_o + start_addr[15:1];
// csr_stb_i
always @(posedge wb_clk_i)
csr_stb_i <= wb_rst_i ? 1'b0 : csr_stb_o;
endmodule
|
/*
* VGA top level file
* Copyright (C) 2010 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module vga (
// Wishbone signals
input wb_clk_i, // 25 Mhz VDU clock
input wb_rst_i,
input [15:0] wb_dat_i,
output [15:0] wb_dat_o,
input [16:1] wb_adr_i,
input wb_we_i,
input wb_tga_i,
input [ 1:0] wb_sel_i,
input wb_stb_i,
input wb_cyc_i,
output wb_ack_o,
// VGA pad signals
output [ 3:0] vga_red_o,
output [ 3:0] vga_green_o,
output [ 3:0] vga_blue_o,
output horiz_sync,
output vert_sync,
// CSR SRAM master interface
output [17:1] csrm_adr_o,
output [ 1:0] csrm_sel_o,
output csrm_we_o,
output [15:0] csrm_dat_o,
input [15:0] csrm_dat_i
);
// Registers and nets
//
// csr address
reg [17:1] csr_adr_i;
reg csr_stb_i;
// Config wires
wire [15:0] conf_wb_dat_o;
wire conf_wb_ack_o;
// Mem wires
wire [15:0] mem_wb_dat_o;
wire mem_wb_ack_o;
// LCD wires
wire [17:1] csr_adr_o;
wire [15:0] csr_dat_i;
wire csr_stb_o;
wire v_retrace;
wire vh_retrace;
wire w_vert_sync;
// VGA configuration registers
wire shift_reg1;
wire graphics_alpha;
wire memory_mapping1;
wire [ 1:0] write_mode;
wire [ 1:0] raster_op;
wire read_mode;
wire [ 7:0] bitmask;
wire [ 3:0] set_reset;
wire [ 3:0] enable_set_reset;
wire [ 3:0] map_mask;
wire x_dotclockdiv2;
wire chain_four;
wire [ 1:0] read_map_select;
wire [ 3:0] color_compare;
wire [ 3:0] color_dont_care;
// Wishbone master to SRAM
wire [17:1] wbm_adr_o;
wire [ 1:0] wbm_sel_o;
wire wbm_we_o;
wire [15:0] wbm_dat_o;
wire [15:0] wbm_dat_i;
wire wbm_stb_o;
wire wbm_ack_i;
wire stb;
// CRT wires
wire [ 5:0] cur_start;
wire [ 5:0] cur_end;
wire [15:0] start_addr;
wire [ 4:0] vcursor;
wire [ 6:0] hcursor;
wire [ 6:0] horiz_total;
wire [ 6:0] end_horiz;
wire [ 6:0] st_hor_retr;
wire [ 4:0] end_hor_retr;
wire [ 9:0] vert_total;
wire [ 9:0] end_vert;
wire [ 9:0] st_ver_retr;
wire [ 3:0] end_ver_retr;
// attribute_ctrl wires
wire [3:0] pal_addr;
wire pal_we;
wire [7:0] pal_read;
wire [7:0] pal_write;
// dac_regs wires
wire dac_we;
wire [1:0] dac_read_data_cycle;
wire [7:0] dac_read_data_register;
wire [3:0] dac_read_data;
wire [1:0] dac_write_data_cycle;
wire [7:0] dac_write_data_register;
wire [3:0] dac_write_data;
// Module instances
//
vga_config_iface config_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wb_dat_i (wb_dat_i),
.wb_dat_o (conf_wb_dat_o),
.wb_adr_i (wb_adr_i[4:1]),
.wb_we_i (wb_we_i),
.wb_sel_i (wb_sel_i),
.wb_stb_i (stb & wb_tga_i),
.wb_ack_o (conf_wb_ack_o),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.x_dotclockdiv2 (x_dotclockdiv2),
.chain_four (chain_four),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.cur_start (cur_start),
.cur_end (cur_end),
.start_addr (start_addr),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_lcd lcd (
.clk (wb_clk_i),
.rst (wb_rst_i),
.shift_reg1 (shift_reg1),
.graphics_alpha (graphics_alpha),
.pal_addr (pal_addr),
.pal_we (pal_we),
.pal_read (pal_read),
.pal_write (pal_write),
.dac_we (dac_we),
.dac_read_data_cycle (dac_read_data_cycle),
.dac_read_data_register (dac_read_data_register),
.dac_read_data (dac_read_data),
.dac_write_data_cycle (dac_write_data_cycle),
.dac_write_data_register (dac_write_data_register),
.dac_write_data (dac_write_data),
.csr_adr_o (csr_adr_o),
.csr_dat_i (csr_dat_i),
.csr_stb_o (csr_stb_o),
.vga_red_o (vga_red_o),
.vga_green_o (vga_green_o),
.vga_blue_o (vga_blue_o),
.horiz_sync (horiz_sync),
.vert_sync (w_vert_sync),
.cur_start (cur_start),
.cur_end (cur_end),
.vcursor (vcursor),
.hcursor (hcursor),
.horiz_total (horiz_total),
.end_horiz (end_horiz),
.st_hor_retr (st_hor_retr),
.end_hor_retr (end_hor_retr),
.vert_total (vert_total),
.end_vert (end_vert),
.st_ver_retr (st_ver_retr),
.end_ver_retr (end_ver_retr),
.x_dotclockdiv2 (x_dotclockdiv2),
.v_retrace (v_retrace),
.vh_retrace (vh_retrace)
);
vga_cpu_mem_iface cpu_mem_iface (
.wb_clk_i (wb_clk_i),
.wb_rst_i (wb_rst_i),
.wbs_adr_i (wb_adr_i),
.wbs_sel_i (wb_sel_i),
.wbs_we_i (wb_we_i),
.wbs_dat_i (wb_dat_i),
.wbs_dat_o (mem_wb_dat_o),
.wbs_stb_i (stb & !wb_tga_i),
.wbs_ack_o (mem_wb_ack_o),
.wbm_adr_o (wbm_adr_o),
.wbm_sel_o (wbm_sel_o),
.wbm_we_o (wbm_we_o),
.wbm_dat_o (wbm_dat_o),
.wbm_dat_i (wbm_dat_i),
.wbm_stb_o (wbm_stb_o),
.wbm_ack_i (wbm_ack_i),
.chain_four (chain_four),
.memory_mapping1 (memory_mapping1),
.write_mode (write_mode),
.raster_op (raster_op),
.read_mode (read_mode),
.bitmask (bitmask),
.set_reset (set_reset),
.enable_set_reset (enable_set_reset),
.map_mask (map_mask),
.read_map_select (read_map_select),
.color_compare (color_compare),
.color_dont_care (color_dont_care)
);
vga_mem_arbitrer mem_arbitrer (
.clk_i (wb_clk_i),
.rst_i (wb_rst_i),
.wb_adr_i (wbm_adr_o),
.wb_sel_i (wbm_sel_o),
.wb_we_i (wbm_we_o),
.wb_dat_i (wbm_dat_o),
.wb_dat_o (wbm_dat_i),
.wb_stb_i (wbm_stb_o),
.wb_ack_o (wbm_ack_i),
.csr_adr_i (csr_adr_i),
.csr_dat_o (csr_dat_i),
.csr_stb_i (csr_stb_i),
.csrm_adr_o (csrm_adr_o),
.csrm_sel_o (csrm_sel_o),
.csrm_we_o (csrm_we_o),
.csrm_dat_o (csrm_dat_o),
.csrm_dat_i (csrm_dat_i)
);
// Continous assignments
assign wb_dat_o = wb_tga_i ? conf_wb_dat_o : mem_wb_dat_o;
assign wb_ack_o = wb_tga_i ? conf_wb_ack_o : mem_wb_ack_o;
assign stb = wb_stb_i & wb_cyc_i;
assign vert_sync = ~graphics_alpha ^ w_vert_sync;
// Behaviour
// csr_adr_i
always @(posedge wb_clk_i)
csr_adr_i <= wb_rst_i ? 17'h0 : csr_adr_o + start_addr[15:1];
// csr_stb_i
always @(posedge wb_clk_i)
csr_stb_i <= wb_rst_i ? 1'b0 : csr_stb_o;
endmodule
|
// This is a component of pluto_servo, a PWM servo driver and quadrature
// counter for emc2
// Copyright 2006 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module main(clk, led, nConfig, epp_nReset, pport_data, nWrite, nWait, nDataStr,
nAddrStr, dout, din, step, dir);
parameter W=10;
parameter F=11;
parameter T=4;
input clk;
output led, nConfig;
inout [7:0] pport_data;
input nWrite;
output nWait;
input nDataStr, nAddrStr, epp_nReset;
input [15:0] din;
reg Spolarity;
reg[13:0] real_dout; output [13:0] dout = do_tristate ? 14'bZ : real_dout;
wire[3:0] real_step; output [3:0] step = do_tristate ? 4'bZ : real_step ^ {4{Spolarity}};
wire[3:0] real_dir; output [3:0] dir = do_tristate ? 4'bZ : real_dir;
wire [W+F-1:0] pos0, pos1, pos2, pos3;
reg [F:0] vel0, vel1, vel2, vel3;
reg [T-1:0] dirtime, steptime;
reg [1:0] tap;
reg [10:0] div2048;
wire stepcnt = ~|(div2048[5:0]);
always @(posedge clk) begin
div2048 <= div2048 + 1'd1;
end
wire do_enable_wdt, do_tristate;
wdt w(clk, do_enable_wdt, &div2048, do_tristate);
stepgen #(W,F,T) s0(clk, stepcnt, pos0, vel0, dirtime, steptime, real_step[0], real_dir[0], tap);
stepgen #(W,F,T) s1(clk, stepcnt, pos1, vel1, dirtime, steptime, real_step[1], real_dir[1], tap);
stepgen #(W,F,T) s2(clk, stepcnt, pos2, vel2, dirtime, steptime, real_step[2], real_dir[2], tap);
stepgen #(W,F,T) s3(clk, stepcnt, pos3, vel3, dirtime, steptime, real_step[3], real_dir[3], tap);
// EPP stuff
wire EPP_write = ~nWrite;
wire EPP_read = nWrite;
wire EPP_addr_strobe = ~nAddrStr;
wire EPP_data_strobe = ~nDataStr;
wire EPP_strobe = EPP_data_strobe | EPP_addr_strobe;
wire EPP_wait; assign nWait = ~EPP_wait;
wire [7:0] EPP_datain = pport_data;
wire [7:0] EPP_dataout; assign pport_data = EPP_dataout;
reg [4:0] EPP_strobe_reg;
always @(posedge clk) EPP_strobe_reg <= {EPP_strobe_reg[3:0], EPP_strobe};
wire EPP_strobe_edge1 = (EPP_strobe_reg[2:1]==2'b01);
// reg led;
assign EPP_wait = EPP_strobe_reg[4];
wire[15:0] EPP_dataword = {EPP_datain, lowbyte};
reg[4:0] addr_reg;
reg[7:0] lowbyte;
always @(posedge clk)
if(EPP_strobe_edge1 & EPP_write & EPP_addr_strobe) begin
addr_reg <= EPP_datain[4:0];
end
else if(EPP_strobe_edge1 & !EPP_addr_strobe) addr_reg <= addr_reg + 4'd1;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_write & EPP_data_strobe) begin
if(addr_reg[3:0] == 4'd1) vel0 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd3) vel1 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd5) vel2 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd7) vel3 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd9) begin
real_dout <= { EPP_datain[5:0], lowbyte };
end
else if(addr_reg[3:0] == 4'd11) begin
tap <= lowbyte[7:6];
steptime <= lowbyte[T-1:0];
Spolarity <= EPP_datain[7];
// EPP_datain[6] is do_enable_wdt
dirtime <= EPP_datain[T-1:0];
end
else lowbyte <= EPP_datain;
end
end
reg [31:0] data_buf;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_read && addr_reg[1:0] == 2'd0) begin
if(addr_reg[4:2] == 3'd0) data_buf <= pos0;
else if(addr_reg[4:2] == 3'd1) data_buf <= pos1;
else if(addr_reg[4:2] == 3'd2) data_buf <= pos2;
else if(addr_reg[4:2] == 3'd3) data_buf <= pos3;
else if(addr_reg[4:2] == 3'd4)
data_buf <= din;
end
end
// the addr_reg test looks funny because it is auto-incremented in an always
// block so "1" reads the low byte, "2 and "3" read middle bytes, and "0"
// reads the high byte I have a feeling that I'm doing this in the wrong way.
wire [7:0] data_reg = addr_reg[1:0] == 2'd1 ? data_buf[7:0] :
(addr_reg[1:0] == 2'd2 ? data_buf[15:8] :
(addr_reg[1:0] == 2'd3 ? data_buf[23:16] :
data_buf[31:24]));
wire [7:0] EPP_data_mux = data_reg;
assign EPP_dataout = (EPP_read & EPP_wait) ? EPP_data_mux : 8'hZZ;
// assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
// assign led = do_tristate ? 1'BZ : (real_step[0] ^ real_dir[0]);
assign led = do_tristate ? 1'bZ : (real_step[0] ^ real_dir[0]);
assign nConfig = epp_nReset; // 1'b1;
assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
endmodule
|
// This is a component of pluto_servo, a PWM servo driver and quadrature
// counter for emc2
// Copyright 2006 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module main(clk, led, nConfig, epp_nReset, pport_data, nWrite, nWait, nDataStr,
nAddrStr, dout, din, step, dir);
parameter W=10;
parameter F=11;
parameter T=4;
input clk;
output led, nConfig;
inout [7:0] pport_data;
input nWrite;
output nWait;
input nDataStr, nAddrStr, epp_nReset;
input [15:0] din;
reg Spolarity;
reg[13:0] real_dout; output [13:0] dout = do_tristate ? 14'bZ : real_dout;
wire[3:0] real_step; output [3:0] step = do_tristate ? 4'bZ : real_step ^ {4{Spolarity}};
wire[3:0] real_dir; output [3:0] dir = do_tristate ? 4'bZ : real_dir;
wire [W+F-1:0] pos0, pos1, pos2, pos3;
reg [F:0] vel0, vel1, vel2, vel3;
reg [T-1:0] dirtime, steptime;
reg [1:0] tap;
reg [10:0] div2048;
wire stepcnt = ~|(div2048[5:0]);
always @(posedge clk) begin
div2048 <= div2048 + 1'd1;
end
wire do_enable_wdt, do_tristate;
wdt w(clk, do_enable_wdt, &div2048, do_tristate);
stepgen #(W,F,T) s0(clk, stepcnt, pos0, vel0, dirtime, steptime, real_step[0], real_dir[0], tap);
stepgen #(W,F,T) s1(clk, stepcnt, pos1, vel1, dirtime, steptime, real_step[1], real_dir[1], tap);
stepgen #(W,F,T) s2(clk, stepcnt, pos2, vel2, dirtime, steptime, real_step[2], real_dir[2], tap);
stepgen #(W,F,T) s3(clk, stepcnt, pos3, vel3, dirtime, steptime, real_step[3], real_dir[3], tap);
// EPP stuff
wire EPP_write = ~nWrite;
wire EPP_read = nWrite;
wire EPP_addr_strobe = ~nAddrStr;
wire EPP_data_strobe = ~nDataStr;
wire EPP_strobe = EPP_data_strobe | EPP_addr_strobe;
wire EPP_wait; assign nWait = ~EPP_wait;
wire [7:0] EPP_datain = pport_data;
wire [7:0] EPP_dataout; assign pport_data = EPP_dataout;
reg [4:0] EPP_strobe_reg;
always @(posedge clk) EPP_strobe_reg <= {EPP_strobe_reg[3:0], EPP_strobe};
wire EPP_strobe_edge1 = (EPP_strobe_reg[2:1]==2'b01);
// reg led;
assign EPP_wait = EPP_strobe_reg[4];
wire[15:0] EPP_dataword = {EPP_datain, lowbyte};
reg[4:0] addr_reg;
reg[7:0] lowbyte;
always @(posedge clk)
if(EPP_strobe_edge1 & EPP_write & EPP_addr_strobe) begin
addr_reg <= EPP_datain[4:0];
end
else if(EPP_strobe_edge1 & !EPP_addr_strobe) addr_reg <= addr_reg + 4'd1;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_write & EPP_data_strobe) begin
if(addr_reg[3:0] == 4'd1) vel0 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd3) vel1 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd5) vel2 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd7) vel3 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd9) begin
real_dout <= { EPP_datain[5:0], lowbyte };
end
else if(addr_reg[3:0] == 4'd11) begin
tap <= lowbyte[7:6];
steptime <= lowbyte[T-1:0];
Spolarity <= EPP_datain[7];
// EPP_datain[6] is do_enable_wdt
dirtime <= EPP_datain[T-1:0];
end
else lowbyte <= EPP_datain;
end
end
reg [31:0] data_buf;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_read && addr_reg[1:0] == 2'd0) begin
if(addr_reg[4:2] == 3'd0) data_buf <= pos0;
else if(addr_reg[4:2] == 3'd1) data_buf <= pos1;
else if(addr_reg[4:2] == 3'd2) data_buf <= pos2;
else if(addr_reg[4:2] == 3'd3) data_buf <= pos3;
else if(addr_reg[4:2] == 3'd4)
data_buf <= din;
end
end
// the addr_reg test looks funny because it is auto-incremented in an always
// block so "1" reads the low byte, "2 and "3" read middle bytes, and "0"
// reads the high byte I have a feeling that I'm doing this in the wrong way.
wire [7:0] data_reg = addr_reg[1:0] == 2'd1 ? data_buf[7:0] :
(addr_reg[1:0] == 2'd2 ? data_buf[15:8] :
(addr_reg[1:0] == 2'd3 ? data_buf[23:16] :
data_buf[31:24]));
wire [7:0] EPP_data_mux = data_reg;
assign EPP_dataout = (EPP_read & EPP_wait) ? EPP_data_mux : 8'hZZ;
// assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
// assign led = do_tristate ? 1'BZ : (real_step[0] ^ real_dir[0]);
assign led = do_tristate ? 1'bZ : (real_step[0] ^ real_dir[0]);
assign nConfig = epp_nReset; // 1'b1;
assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
endmodule
|
// This is a component of pluto_servo, a PWM servo driver and quadrature
// counter for emc2
// Copyright 2006 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module main(clk, led, nConfig, epp_nReset, pport_data, nWrite, nWait, nDataStr,
nAddrStr, dout, din, step, dir);
parameter W=10;
parameter F=11;
parameter T=4;
input clk;
output led, nConfig;
inout [7:0] pport_data;
input nWrite;
output nWait;
input nDataStr, nAddrStr, epp_nReset;
input [15:0] din;
reg Spolarity;
reg[13:0] real_dout; output [13:0] dout = do_tristate ? 14'bZ : real_dout;
wire[3:0] real_step; output [3:0] step = do_tristate ? 4'bZ : real_step ^ {4{Spolarity}};
wire[3:0] real_dir; output [3:0] dir = do_tristate ? 4'bZ : real_dir;
wire [W+F-1:0] pos0, pos1, pos2, pos3;
reg [F:0] vel0, vel1, vel2, vel3;
reg [T-1:0] dirtime, steptime;
reg [1:0] tap;
reg [10:0] div2048;
wire stepcnt = ~|(div2048[5:0]);
always @(posedge clk) begin
div2048 <= div2048 + 1'd1;
end
wire do_enable_wdt, do_tristate;
wdt w(clk, do_enable_wdt, &div2048, do_tristate);
stepgen #(W,F,T) s0(clk, stepcnt, pos0, vel0, dirtime, steptime, real_step[0], real_dir[0], tap);
stepgen #(W,F,T) s1(clk, stepcnt, pos1, vel1, dirtime, steptime, real_step[1], real_dir[1], tap);
stepgen #(W,F,T) s2(clk, stepcnt, pos2, vel2, dirtime, steptime, real_step[2], real_dir[2], tap);
stepgen #(W,F,T) s3(clk, stepcnt, pos3, vel3, dirtime, steptime, real_step[3], real_dir[3], tap);
// EPP stuff
wire EPP_write = ~nWrite;
wire EPP_read = nWrite;
wire EPP_addr_strobe = ~nAddrStr;
wire EPP_data_strobe = ~nDataStr;
wire EPP_strobe = EPP_data_strobe | EPP_addr_strobe;
wire EPP_wait; assign nWait = ~EPP_wait;
wire [7:0] EPP_datain = pport_data;
wire [7:0] EPP_dataout; assign pport_data = EPP_dataout;
reg [4:0] EPP_strobe_reg;
always @(posedge clk) EPP_strobe_reg <= {EPP_strobe_reg[3:0], EPP_strobe};
wire EPP_strobe_edge1 = (EPP_strobe_reg[2:1]==2'b01);
// reg led;
assign EPP_wait = EPP_strobe_reg[4];
wire[15:0] EPP_dataword = {EPP_datain, lowbyte};
reg[4:0] addr_reg;
reg[7:0] lowbyte;
always @(posedge clk)
if(EPP_strobe_edge1 & EPP_write & EPP_addr_strobe) begin
addr_reg <= EPP_datain[4:0];
end
else if(EPP_strobe_edge1 & !EPP_addr_strobe) addr_reg <= addr_reg + 4'd1;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_write & EPP_data_strobe) begin
if(addr_reg[3:0] == 4'd1) vel0 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd3) vel1 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd5) vel2 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd7) vel3 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd9) begin
real_dout <= { EPP_datain[5:0], lowbyte };
end
else if(addr_reg[3:0] == 4'd11) begin
tap <= lowbyte[7:6];
steptime <= lowbyte[T-1:0];
Spolarity <= EPP_datain[7];
// EPP_datain[6] is do_enable_wdt
dirtime <= EPP_datain[T-1:0];
end
else lowbyte <= EPP_datain;
end
end
reg [31:0] data_buf;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_read && addr_reg[1:0] == 2'd0) begin
if(addr_reg[4:2] == 3'd0) data_buf <= pos0;
else if(addr_reg[4:2] == 3'd1) data_buf <= pos1;
else if(addr_reg[4:2] == 3'd2) data_buf <= pos2;
else if(addr_reg[4:2] == 3'd3) data_buf <= pos3;
else if(addr_reg[4:2] == 3'd4)
data_buf <= din;
end
end
// the addr_reg test looks funny because it is auto-incremented in an always
// block so "1" reads the low byte, "2 and "3" read middle bytes, and "0"
// reads the high byte I have a feeling that I'm doing this in the wrong way.
wire [7:0] data_reg = addr_reg[1:0] == 2'd1 ? data_buf[7:0] :
(addr_reg[1:0] == 2'd2 ? data_buf[15:8] :
(addr_reg[1:0] == 2'd3 ? data_buf[23:16] :
data_buf[31:24]));
wire [7:0] EPP_data_mux = data_reg;
assign EPP_dataout = (EPP_read & EPP_wait) ? EPP_data_mux : 8'hZZ;
// assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
// assign led = do_tristate ? 1'BZ : (real_step[0] ^ real_dir[0]);
assign led = do_tristate ? 1'bZ : (real_step[0] ^ real_dir[0]);
assign nConfig = epp_nReset; // 1'b1;
assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
endmodule
|
// This is a component of pluto_servo, a PWM servo driver and quadrature
// counter for emc2
// Copyright 2006 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module main(clk, led, nConfig, epp_nReset, pport_data, nWrite, nWait, nDataStr,
nAddrStr, dout, din, step, dir);
parameter W=10;
parameter F=11;
parameter T=4;
input clk;
output led, nConfig;
inout [7:0] pport_data;
input nWrite;
output nWait;
input nDataStr, nAddrStr, epp_nReset;
input [15:0] din;
reg Spolarity;
reg[13:0] real_dout; output [13:0] dout = do_tristate ? 14'bZ : real_dout;
wire[3:0] real_step; output [3:0] step = do_tristate ? 4'bZ : real_step ^ {4{Spolarity}};
wire[3:0] real_dir; output [3:0] dir = do_tristate ? 4'bZ : real_dir;
wire [W+F-1:0] pos0, pos1, pos2, pos3;
reg [F:0] vel0, vel1, vel2, vel3;
reg [T-1:0] dirtime, steptime;
reg [1:0] tap;
reg [10:0] div2048;
wire stepcnt = ~|(div2048[5:0]);
always @(posedge clk) begin
div2048 <= div2048 + 1'd1;
end
wire do_enable_wdt, do_tristate;
wdt w(clk, do_enable_wdt, &div2048, do_tristate);
stepgen #(W,F,T) s0(clk, stepcnt, pos0, vel0, dirtime, steptime, real_step[0], real_dir[0], tap);
stepgen #(W,F,T) s1(clk, stepcnt, pos1, vel1, dirtime, steptime, real_step[1], real_dir[1], tap);
stepgen #(W,F,T) s2(clk, stepcnt, pos2, vel2, dirtime, steptime, real_step[2], real_dir[2], tap);
stepgen #(W,F,T) s3(clk, stepcnt, pos3, vel3, dirtime, steptime, real_step[3], real_dir[3], tap);
// EPP stuff
wire EPP_write = ~nWrite;
wire EPP_read = nWrite;
wire EPP_addr_strobe = ~nAddrStr;
wire EPP_data_strobe = ~nDataStr;
wire EPP_strobe = EPP_data_strobe | EPP_addr_strobe;
wire EPP_wait; assign nWait = ~EPP_wait;
wire [7:0] EPP_datain = pport_data;
wire [7:0] EPP_dataout; assign pport_data = EPP_dataout;
reg [4:0] EPP_strobe_reg;
always @(posedge clk) EPP_strobe_reg <= {EPP_strobe_reg[3:0], EPP_strobe};
wire EPP_strobe_edge1 = (EPP_strobe_reg[2:1]==2'b01);
// reg led;
assign EPP_wait = EPP_strobe_reg[4];
wire[15:0] EPP_dataword = {EPP_datain, lowbyte};
reg[4:0] addr_reg;
reg[7:0] lowbyte;
always @(posedge clk)
if(EPP_strobe_edge1 & EPP_write & EPP_addr_strobe) begin
addr_reg <= EPP_datain[4:0];
end
else if(EPP_strobe_edge1 & !EPP_addr_strobe) addr_reg <= addr_reg + 4'd1;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_write & EPP_data_strobe) begin
if(addr_reg[3:0] == 4'd1) vel0 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd3) vel1 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd5) vel2 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd7) vel3 <= EPP_dataword[F:0];
else if(addr_reg[3:0] == 4'd9) begin
real_dout <= { EPP_datain[5:0], lowbyte };
end
else if(addr_reg[3:0] == 4'd11) begin
tap <= lowbyte[7:6];
steptime <= lowbyte[T-1:0];
Spolarity <= EPP_datain[7];
// EPP_datain[6] is do_enable_wdt
dirtime <= EPP_datain[T-1:0];
end
else lowbyte <= EPP_datain;
end
end
reg [31:0] data_buf;
always @(posedge clk) begin
if(EPP_strobe_edge1 & EPP_read && addr_reg[1:0] == 2'd0) begin
if(addr_reg[4:2] == 3'd0) data_buf <= pos0;
else if(addr_reg[4:2] == 3'd1) data_buf <= pos1;
else if(addr_reg[4:2] == 3'd2) data_buf <= pos2;
else if(addr_reg[4:2] == 3'd3) data_buf <= pos3;
else if(addr_reg[4:2] == 3'd4)
data_buf <= din;
end
end
// the addr_reg test looks funny because it is auto-incremented in an always
// block so "1" reads the low byte, "2 and "3" read middle bytes, and "0"
// reads the high byte I have a feeling that I'm doing this in the wrong way.
wire [7:0] data_reg = addr_reg[1:0] == 2'd1 ? data_buf[7:0] :
(addr_reg[1:0] == 2'd2 ? data_buf[15:8] :
(addr_reg[1:0] == 2'd3 ? data_buf[23:16] :
data_buf[31:24]));
wire [7:0] EPP_data_mux = data_reg;
assign EPP_dataout = (EPP_read & EPP_wait) ? EPP_data_mux : 8'hZZ;
// assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
// assign led = do_tristate ? 1'BZ : (real_step[0] ^ real_dir[0]);
assign led = do_tristate ? 1'bZ : (real_step[0] ^ real_dir[0]);
assign nConfig = epp_nReset; // 1'b1;
assign do_enable_wdt = EPP_strobe_edge1 & EPP_write & EPP_data_strobe & (addr_reg[3:0] == 4'd9) & EPP_datain[6];
endmodule
|
// -*- verilog -*-
//
// USRP - Universal Software Radio Peripheral
//
// Copyright (C) 2003 Matt Ettus
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 51 Franklin Street, Boston, MA 02110-1301 USA
//
// DDC block
module ddc(input clock,
input reset,
input enable,
input [3:0] rate1,
input [3:0] rate2,
output strobe,
input [31:0] freq,
input [15:0] i_in,
input [15:0] q_in,
output [15:0] i_out,
output [15:0] q_out
);
parameter bw = 16;
parameter zw = 16;
wire [15:0] i_cordic_out, q_cordic_out;
wire [31:0] phase;
wire strobe1, strobe2;
reg [3:0] strobe_ctr1,strobe_ctr2;
always @(posedge clock)
if(reset | ~enable)
strobe_ctr2 <= #1 4'd0;
else if(strobe2)
strobe_ctr2 <= #1 4'd0;
else
strobe_ctr2 <= #1 strobe_ctr2 + 4'd1;
always @(posedge clock)
if(reset | ~enable)
strobe_ctr1 <= #1 4'd0;
else if(strobe1)
strobe_ctr1 <= #1 4'd0;
else if(strobe2)
strobe_ctr1 <= #1 strobe_ctr1 + 4'd1;
assign strobe2 = enable & ( strobe_ctr2 == rate2 );
assign strobe1 = strobe2 & ( strobe_ctr1 == rate1 );
assign strobe = strobe1;
function [2:0] log_ceil;
input [3:0] val;
log_ceil = val[3] ? 3'd4 : val[2] ? 3'd3 : val[1] ? 3'd2 : 3'd1;
endfunction
wire [2:0] shift1 = log_ceil(rate1);
wire [2:0] shift2 = log_ceil(rate2);
cordic #(.bitwidth(bw),.zwidth(zw),.stages(16))
cordic(.clock(clock), .reset(reset), .enable(enable),
.xi(i_in), .yi(q_in), .zi(phase[31:32-zw]),
.xo(i_cordic_out), .yo(q_cordic_out), .zo() );
cic_decim_2stage #(.bw(bw),.N(4))
decim_i(.clock(clock),.reset(reset),.enable(enable),
.strobe1(1'b1),.strobe2(strobe2),.strobe3(strobe1),.shift1(shift2),.shift2(shift1),
.signal_in(i_cordic_out),.signal_out(i_out));
cic_decim_2stage #(.bw(bw),.N(4))
decim_q(.clock(clock),.reset(reset),.enable(enable),
.strobe1(1'b1),.strobe2(strobe2),.strobe3(strobe1),.shift1(shift2),.shift2(shift1),
.signal_in(q_cordic_out),.signal_out(q_out));
phase_acc #(.resolution(32))
nco (.clk(clock),.reset(reset),.enable(enable),
.freq(freq),.phase(phase));
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
// Copyright (C) 2008 Schuyler Eldridge, Boston University
//
// This program is free software: you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation, either version 3 of the License.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program. If not, see <http://www.gnu.org/licenses/>.
module mux(opA,opB,sum,dsp_sel,out);
input [3:0] opA,opB;
input [4:0] sum;
input [1:0] dsp_sel;
output [3:0] out;
reg cout;
always @ (sum)
begin
if (sum[4] == 1)
cout <= 4'b0001;
else
cout <= 4'b0000;
end
reg out;
always @(dsp_sel,sum,cout,opB,opA)
begin
if (dsp_sel == 2'b00)
out <= sum[3:0];
else if (dsp_sel == 2'b01)
out <= cout;
else if (dsp_sel == 2'b10)
out <= opB;
else if (dsp_sel == 2'b11)
out <= opA;
end
endmodule
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/11/2016 02:09:05 PM
// Design Name:
// Module Name: Rotate_Mux_Array
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Rotate_Mux_Array
#(parameter SWR=26)
(
input wire [SWR-1:0] Data_i,
input wire select_i,
output wire [SWR-1:0] Data_o
);
genvar j;//Create a variable for the loop FOR
generate for (j=0; j <= SWR-1; j=j+1) begin // generate enough Multiplexers modules for each bit
case (j)
SWR-1-j:begin
assign Data_o[j]=Data_i[SWR-1-j];
end
default:begin
Multiplexer_AC #(.W(1)) rotate_mux(
.ctrl(select_i),
.D0 (Data_i[j]),
.D1 (Data_i[SWR-1-j]),
.S (Data_o[j])
);
end
endcase
end
endgenerate
endmodule
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/11/2016 02:09:05 PM
// Design Name:
// Module Name: Rotate_Mux_Array
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Rotate_Mux_Array
#(parameter SWR=26)
(
input wire [SWR-1:0] Data_i,
input wire select_i,
output wire [SWR-1:0] Data_o
);
genvar j;//Create a variable for the loop FOR
generate for (j=0; j <= SWR-1; j=j+1) begin // generate enough Multiplexers modules for each bit
case (j)
SWR-1-j:begin
assign Data_o[j]=Data_i[SWR-1-j];
end
default:begin
Multiplexer_AC #(.W(1)) rotate_mux(
.ctrl(select_i),
.D0 (Data_i[j]),
.D1 (Data_i[SWR-1-j]),
.S (Data_o[j])
);
end
endcase
end
endgenerate
endmodule
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/11/2016 02:09:05 PM
// Design Name:
// Module Name: Rotate_Mux_Array
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Rotate_Mux_Array
#(parameter SWR=26)
(
input wire [SWR-1:0] Data_i,
input wire select_i,
output wire [SWR-1:0] Data_o
);
genvar j;//Create a variable for the loop FOR
generate for (j=0; j <= SWR-1; j=j+1) begin // generate enough Multiplexers modules for each bit
case (j)
SWR-1-j:begin
assign Data_o[j]=Data_i[SWR-1-j];
end
default:begin
Multiplexer_AC #(.W(1)) rotate_mux(
.ctrl(select_i),
.D0 (Data_i[j]),
.D1 (Data_i[SWR-1-j]),
.S (Data_o[j])
);
end
endcase
end
endgenerate
endmodule
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/11/2016 02:09:05 PM
// Design Name:
// Module Name: Rotate_Mux_Array
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Rotate_Mux_Array
#(parameter SWR=26)
(
input wire [SWR-1:0] Data_i,
input wire select_i,
output wire [SWR-1:0] Data_o
);
genvar j;//Create a variable for the loop FOR
generate for (j=0; j <= SWR-1; j=j+1) begin // generate enough Multiplexers modules for each bit
case (j)
SWR-1-j:begin
assign Data_o[j]=Data_i[SWR-1-j];
end
default:begin
Multiplexer_AC #(.W(1)) rotate_mux(
.ctrl(select_i),
.D0 (Data_i[j]),
.D1 (Data_i[SWR-1-j]),
.S (Data_o[j])
);
end
endcase
end
endgenerate
endmodule
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/11/2016 02:09:05 PM
// Design Name:
// Module Name: Rotate_Mux_Array
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Rotate_Mux_Array
#(parameter SWR=26)
(
input wire [SWR-1:0] Data_i,
input wire select_i,
output wire [SWR-1:0] Data_o
);
genvar j;//Create a variable for the loop FOR
generate for (j=0; j <= SWR-1; j=j+1) begin // generate enough Multiplexers modules for each bit
case (j)
SWR-1-j:begin
assign Data_o[j]=Data_i[SWR-1-j];
end
default:begin
Multiplexer_AC #(.W(1)) rotate_mux(
.ctrl(select_i),
.D0 (Data_i[j]),
.D1 (Data_i[SWR-1-j]),
.S (Data_o[j])
);
end
endcase
end
endgenerate
endmodule
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/11/2016 02:09:05 PM
// Design Name:
// Module Name: Rotate_Mux_Array
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Rotate_Mux_Array
#(parameter SWR=26)
(
input wire [SWR-1:0] Data_i,
input wire select_i,
output wire [SWR-1:0] Data_o
);
genvar j;//Create a variable for the loop FOR
generate for (j=0; j <= SWR-1; j=j+1) begin // generate enough Multiplexers modules for each bit
case (j)
SWR-1-j:begin
assign Data_o[j]=Data_i[SWR-1-j];
end
default:begin
Multiplexer_AC #(.W(1)) rotate_mux(
.ctrl(select_i),
.D0 (Data_i[j]),
.D1 (Data_i[SWR-1-j]),
.S (Data_o[j])
);
end
endcase
end
endgenerate
endmodule
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: Address AXI3 Slave Converter
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// a_axi3_conv
// axic_fifo
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_a_axi3_conv #
(
parameter C_FAMILY = "none",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_USER_SIGNALS = 0,
parameter integer C_AXI_AUSER_WIDTH = 1,
parameter integer C_AXI_CHANNEL = 0,
// 0 = AXI AW Channel.
// 1 = AXI AR Channel.
parameter integer C_SUPPORT_SPLITTING = 1,
// Implement transaction splitting logic.
// Disabled whan all connected masters are AXI3 and have same or narrower data width.
parameter integer C_SUPPORT_BURSTS = 1,
// Disabled when all connected masters are AxiLite,
// allowing logic to be simplified.
parameter integer C_SINGLE_THREAD = 1
// 0 = Ignore ID when propagating transactions (assume all responses are in order).
// 1 = Enforce single-threading (one ID at a time) when any outstanding or
// requested transaction requires splitting.
// While no split is ongoing any new non-split transaction will pass immediately regardless
// off ID.
// A split transaction will stall if there are multiple ID (non-split) transactions
// ongoing, once it has been forwarded only transactions with the same ID is allowed
// (split or not) until all ongoing split transactios has been completed.
)
(
// System Signals
input wire ACLK,
input wire ARESET,
// Command Interface (W/R)
output wire cmd_valid,
output wire cmd_split,
output wire [C_AXI_ID_WIDTH-1:0] cmd_id,
output wire [4-1:0] cmd_length,
input wire cmd_ready,
// Command Interface (B)
output wire cmd_b_valid,
output wire cmd_b_split,
output wire [4-1:0] cmd_b_repeat,
input wire cmd_b_ready,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AADDR,
input wire [8-1:0] S_AXI_ALEN,
input wire [3-1:0] S_AXI_ASIZE,
input wire [2-1:0] S_AXI_ABURST,
input wire [1-1:0] S_AXI_ALOCK,
input wire [4-1:0] S_AXI_ACACHE,
input wire [3-1:0] S_AXI_APROT,
input wire [4-1:0] S_AXI_AQOS,
input wire [C_AXI_AUSER_WIDTH-1:0] S_AXI_AUSER,
input wire S_AXI_AVALID,
output wire S_AXI_AREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AADDR,
output wire [4-1:0] M_AXI_ALEN,
output wire [3-1:0] M_AXI_ASIZE,
output wire [2-1:0] M_AXI_ABURST,
output wire [2-1:0] M_AXI_ALOCK,
output wire [4-1:0] M_AXI_ACACHE,
output wire [3-1:0] M_AXI_APROT,
output wire [4-1:0] M_AXI_AQOS,
output wire [C_AXI_AUSER_WIDTH-1:0] M_AXI_AUSER,
output wire M_AXI_AVALID,
input wire M_AXI_AREADY
);
/////////////////////////////////////////////////////////////////////////////
// Variables for generating parameter controlled instances.
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
// Constants for burst types.
localparam [2-1:0] C_FIX_BURST = 2'b00;
localparam [2-1:0] C_INCR_BURST = 2'b01;
localparam [2-1:0] C_WRAP_BURST = 2'b10;
// Depth for command FIFO.
localparam integer C_FIFO_DEPTH_LOG = 5;
// Constants used to generate size mask.
localparam [C_AXI_ADDR_WIDTH+8-1:0] C_SIZE_MASK = {{C_AXI_ADDR_WIDTH{1'b1}}, 8'b0000_0000};
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Access decoding related signals.
wire access_is_incr;
wire [4-1:0] num_transactions;
wire incr_need_to_split;
reg [C_AXI_ADDR_WIDTH-1:0] next_mi_addr;
reg split_ongoing;
reg [4-1:0] pushed_commands;
reg [16-1:0] addr_step;
reg [16-1:0] first_step;
wire [8-1:0] first_beats;
reg [C_AXI_ADDR_WIDTH-1:0] size_mask;
// Access decoding related signals for internal pipestage.
reg access_is_incr_q;
reg incr_need_to_split_q;
wire need_to_split_q;
reg [4-1:0] num_transactions_q;
reg [16-1:0] addr_step_q;
reg [16-1:0] first_step_q;
reg [C_AXI_ADDR_WIDTH-1:0] size_mask_q;
// Command buffer help signals.
reg [C_FIFO_DEPTH_LOG:0] cmd_depth;
reg cmd_empty;
reg [C_AXI_ID_WIDTH-1:0] queue_id;
wire id_match;
wire cmd_id_check;
wire s_ready;
wire cmd_full;
wire allow_this_cmd;
wire allow_new_cmd;
wire cmd_push;
reg cmd_push_block;
reg [C_FIFO_DEPTH_LOG:0] cmd_b_depth;
reg cmd_b_empty;
wire cmd_b_full;
wire cmd_b_push;
reg cmd_b_push_block;
wire pushed_new_cmd;
wire last_incr_split;
wire last_split;
wire first_split;
wire no_cmd;
wire allow_split_cmd;
wire almost_empty;
wire no_b_cmd;
wire allow_non_split_cmd;
wire almost_b_empty;
reg multiple_id_non_split;
reg split_in_progress;
// Internal Command Interface signals (W/R).
wire cmd_split_i;
wire [C_AXI_ID_WIDTH-1:0] cmd_id_i;
reg [4-1:0] cmd_length_i;
// Internal Command Interface signals (B).
wire cmd_b_split_i;
wire [4-1:0] cmd_b_repeat_i;
// Throttling help signals.
wire mi_stalling;
reg command_ongoing;
// Internal SI-side signals.
reg [C_AXI_ID_WIDTH-1:0] S_AXI_AID_Q;
reg [C_AXI_ADDR_WIDTH-1:0] S_AXI_AADDR_Q;
reg [8-1:0] S_AXI_ALEN_Q;
reg [3-1:0] S_AXI_ASIZE_Q;
reg [2-1:0] S_AXI_ABURST_Q;
reg [2-1:0] S_AXI_ALOCK_Q;
reg [4-1:0] S_AXI_ACACHE_Q;
reg [3-1:0] S_AXI_APROT_Q;
reg [4-1:0] S_AXI_AQOS_Q;
reg [C_AXI_AUSER_WIDTH-1:0] S_AXI_AUSER_Q;
reg S_AXI_AREADY_I;
// Internal MI-side signals.
wire [C_AXI_ID_WIDTH-1:0] M_AXI_AID_I;
reg [C_AXI_ADDR_WIDTH-1:0] M_AXI_AADDR_I;
reg [8-1:0] M_AXI_ALEN_I;
wire [3-1:0] M_AXI_ASIZE_I;
wire [2-1:0] M_AXI_ABURST_I;
reg [2-1:0] M_AXI_ALOCK_I;
wire [4-1:0] M_AXI_ACACHE_I;
wire [3-1:0] M_AXI_APROT_I;
wire [4-1:0] M_AXI_AQOS_I;
wire [C_AXI_AUSER_WIDTH-1:0] M_AXI_AUSER_I;
wire M_AXI_AVALID_I;
wire M_AXI_AREADY_I;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ARESET};
end
/////////////////////////////////////////////////////////////////////////////
// Capture SI-Side signals.
//
/////////////////////////////////////////////////////////////////////////////
// Register SI-Side signals.
always @ (posedge ACLK) begin
if ( ARESET ) begin
S_AXI_AID_Q <= {C_AXI_ID_WIDTH{1'b0}};
S_AXI_AADDR_Q <= {C_AXI_ADDR_WIDTH{1'b0}};
S_AXI_ALEN_Q <= 8'b0;
S_AXI_ASIZE_Q <= 3'b0;
S_AXI_ABURST_Q <= 2'b0;
S_AXI_ALOCK_Q <= 2'b0;
S_AXI_ACACHE_Q <= 4'b0;
S_AXI_APROT_Q <= 3'b0;
S_AXI_AQOS_Q <= 4'b0;
S_AXI_AUSER_Q <= {C_AXI_AUSER_WIDTH{1'b0}};
end else begin
if ( S_AXI_AREADY_I ) begin
S_AXI_AID_Q <= S_AXI_AID;
S_AXI_AADDR_Q <= S_AXI_AADDR;
S_AXI_ALEN_Q <= S_AXI_ALEN;
S_AXI_ASIZE_Q <= S_AXI_ASIZE;
S_AXI_ABURST_Q <= S_AXI_ABURST;
S_AXI_ALOCK_Q <= S_AXI_ALOCK;
S_AXI_ACACHE_Q <= S_AXI_ACACHE;
S_AXI_APROT_Q <= S_AXI_APROT;
S_AXI_AQOS_Q <= S_AXI_AQOS;
S_AXI_AUSER_Q <= S_AXI_AUSER;
end
end
end
/////////////////////////////////////////////////////////////////////////////
// Decode the Incoming Transaction.
//
// Extract transaction type and the number of splits that may be needed.
//
// Calculate the step size so that the address for each part of a split can
// can be calculated.
//
/////////////////////////////////////////////////////////////////////////////
// Transaction burst type.
assign access_is_incr = ( S_AXI_ABURST == C_INCR_BURST );
// Get number of transactions for split INCR.
assign num_transactions = S_AXI_ALEN[4 +: 4];
assign first_beats = {3'b0, S_AXI_ALEN[0 +: 4]} + 7'b01;
// Generate address increment of first split transaction.
always @ *
begin
case (S_AXI_ASIZE)
3'b000: first_step = first_beats << 0;
3'b001: first_step = first_beats << 1;
3'b010: first_step = first_beats << 2;
3'b011: first_step = first_beats << 3;
3'b100: first_step = first_beats << 4;
3'b101: first_step = first_beats << 5;
3'b110: first_step = first_beats << 6;
3'b111: first_step = first_beats << 7;
endcase
end
// Generate address increment for remaining split transactions.
always @ *
begin
case (S_AXI_ASIZE)
3'b000: addr_step = 16'h0010;
3'b001: addr_step = 16'h0020;
3'b010: addr_step = 16'h0040;
3'b011: addr_step = 16'h0080;
3'b100: addr_step = 16'h0100;
3'b101: addr_step = 16'h0200;
3'b110: addr_step = 16'h0400;
3'b111: addr_step = 16'h0800;
endcase
end
// Generate address mask bits to remove split transaction unalignment.
always @ *
begin
case (S_AXI_ASIZE)
3'b000: size_mask = C_SIZE_MASK[8 +: C_AXI_ADDR_WIDTH];
3'b001: size_mask = C_SIZE_MASK[7 +: C_AXI_ADDR_WIDTH];
3'b010: size_mask = C_SIZE_MASK[6 +: C_AXI_ADDR_WIDTH];
3'b011: size_mask = C_SIZE_MASK[5 +: C_AXI_ADDR_WIDTH];
3'b100: size_mask = C_SIZE_MASK[4 +: C_AXI_ADDR_WIDTH];
3'b101: size_mask = C_SIZE_MASK[3 +: C_AXI_ADDR_WIDTH];
3'b110: size_mask = C_SIZE_MASK[2 +: C_AXI_ADDR_WIDTH];
3'b111: size_mask = C_SIZE_MASK[1 +: C_AXI_ADDR_WIDTH];
endcase
end
/////////////////////////////////////////////////////////////////////////////
// Transfer SI-Side signals to internal Pipeline Stage.
//
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
if ( ARESET ) begin
access_is_incr_q <= 1'b0;
incr_need_to_split_q <= 1'b0;
num_transactions_q <= 4'b0;
addr_step_q <= 16'b0;
first_step_q <= 16'b0;
size_mask_q <= {C_AXI_ADDR_WIDTH{1'b0}};
end else begin
if ( S_AXI_AREADY_I ) begin
access_is_incr_q <= access_is_incr;
incr_need_to_split_q <= incr_need_to_split;
num_transactions_q <= num_transactions;
addr_step_q <= addr_step;
first_step_q <= first_step;
size_mask_q <= size_mask;
end
end
end
/////////////////////////////////////////////////////////////////////////////
// Generate Command Information.
//
// Detect if current transation needs to be split, and keep track of all
// the generated split transactions.
//
//
/////////////////////////////////////////////////////////////////////////////
// Detect when INCR must be split.
assign incr_need_to_split = access_is_incr & ( num_transactions != 0 ) &
( C_SUPPORT_SPLITTING == 1 ) &
( C_SUPPORT_BURSTS == 1 );
// Detect when a command has to be split.
assign need_to_split_q = incr_need_to_split_q;
// Handle progress of split transactions.
always @ (posedge ACLK) begin
if ( ARESET ) begin
split_ongoing <= 1'b0;
end else begin
if ( pushed_new_cmd ) begin
split_ongoing <= need_to_split_q & ~last_split;
end
end
end
// Keep track of number of transactions generated.
always @ (posedge ACLK) begin
if ( ARESET ) begin
pushed_commands <= 4'b0;
end else begin
if ( S_AXI_AREADY_I ) begin
pushed_commands <= 4'b0;
end else if ( pushed_new_cmd ) begin
pushed_commands <= pushed_commands + 4'b1;
end
end
end
// Detect last part of a command, split or not.
assign last_incr_split = access_is_incr_q & ( num_transactions_q == pushed_commands );
assign last_split = last_incr_split | ~access_is_incr_q |
( C_SUPPORT_SPLITTING == 0 ) |
( C_SUPPORT_BURSTS == 0 );
assign first_split = (pushed_commands == 4'b0);
// Calculate base for next address.
always @ (posedge ACLK) begin
if ( ARESET ) begin
next_mi_addr = {C_AXI_ADDR_WIDTH{1'b0}};
end else if ( pushed_new_cmd ) begin
next_mi_addr = M_AXI_AADDR_I + (first_split ? first_step_q : addr_step_q);
end
end
/////////////////////////////////////////////////////////////////////////////
// Translating Transaction.
//
// Set Split transaction information on all part except last for a transaction
// that needs splitting.
// The B Channel will only get one command for a Split transaction and in
// the Split bflag will be set in that case.
//
// The AWID is extracted and applied to all commands generated for the current
// incomming SI-Side transaction.
//
// The address is increased for each part of a Split transaction, the amount
// depends on the siSIZE for the transaction.
//
// The length has to be changed for Split transactions. All part except tha
// last one will have 0xF, the last one uses the 4 lsb bits from the SI-side
// transaction as length.
//
// Non-Split has untouched address and length information.
//
// Exclusive access are diasabled for a Split transaction because it is not
// possible to guarantee concistency between all the parts.
//
/////////////////////////////////////////////////////////////////////////////
// Assign Split signals.
assign cmd_split_i = need_to_split_q & ~last_split;
assign cmd_b_split_i = need_to_split_q & ~last_split;
// Copy AW ID to W.
assign cmd_id_i = S_AXI_AID_Q;
// Set B Responses to merge.
assign cmd_b_repeat_i = num_transactions_q;
// Select new size or remaining size.
always @ *
begin
if ( split_ongoing & access_is_incr_q ) begin
M_AXI_AADDR_I = next_mi_addr & size_mask_q;
end else begin
M_AXI_AADDR_I = S_AXI_AADDR_Q;
end
end
// Generate the base length for each transaction.
always @ *
begin
if ( first_split | ~need_to_split_q ) begin
M_AXI_ALEN_I = S_AXI_ALEN_Q[0 +: 4];
cmd_length_i = S_AXI_ALEN_Q[0 +: 4];
end else begin
M_AXI_ALEN_I = 4'hF;
cmd_length_i = 4'hF;
end
end
// Kill Exclusive for Split transactions.
always @ *
begin
if ( need_to_split_q ) begin
M_AXI_ALOCK_I = 2'b00;
end else begin
M_AXI_ALOCK_I = {1'b0, S_AXI_ALOCK_Q};
end
end
/////////////////////////////////////////////////////////////////////////////
// Forward the command to the MI-side interface.
//
// It is determined that this is an allowed command/access when there is
// room in the command queue (and it passes ID and Split checks as required).
//
/////////////////////////////////////////////////////////////////////////////
// Move SI-side transaction to internal pipe stage.
always @ (posedge ACLK) begin
if (ARESET) begin
command_ongoing <= 1'b0;
S_AXI_AREADY_I <= 1'b0;
end else begin
if (areset_d == 2'b10) begin
S_AXI_AREADY_I <= 1'b1;
end else begin
if ( S_AXI_AVALID & S_AXI_AREADY_I ) begin
command_ongoing <= 1'b1;
S_AXI_AREADY_I <= 1'b0;
end else if ( pushed_new_cmd & last_split ) begin
command_ongoing <= 1'b0;
S_AXI_AREADY_I <= 1'b1;
end
end
end
end
// Generate ready signal.
assign S_AXI_AREADY = S_AXI_AREADY_I;
// Only allowed to forward translated command when command queue is ok with it.
assign M_AXI_AVALID_I = allow_new_cmd & command_ongoing;
// Detect when MI-side is stalling.
assign mi_stalling = M_AXI_AVALID_I & ~M_AXI_AREADY_I;
/////////////////////////////////////////////////////////////////////////////
// Simple transfer of paramters that doesn't need to be adjusted.
//
// ID - Transaction still recognized with the same ID.
// CACHE - No need to change the chache features. Even if the modyfiable
// bit is overridden (forcefully) there is no need to let downstream
// component beleive it is ok to modify it further.
// PROT - Security level of access is not changed when upsizing.
// QOS - Quality of Service is static 0.
// USER - User bits remains the same.
//
/////////////////////////////////////////////////////////////////////////////
assign M_AXI_AID_I = S_AXI_AID_Q;
assign M_AXI_ASIZE_I = S_AXI_ASIZE_Q;
assign M_AXI_ABURST_I = S_AXI_ABURST_Q;
assign M_AXI_ACACHE_I = S_AXI_ACACHE_Q;
assign M_AXI_APROT_I = S_AXI_APROT_Q;
assign M_AXI_AQOS_I = S_AXI_AQOS_Q;
assign M_AXI_AUSER_I = ( C_AXI_SUPPORTS_USER_SIGNALS ) ? S_AXI_AUSER_Q : {C_AXI_AUSER_WIDTH{1'b0}};
/////////////////////////////////////////////////////////////////////////////
// Control command queue to W/R channel.
//
// Commands can be pushed into the Cmd FIFO even if MI-side is stalling.
// A flag is set if MI-side is stalling when Command is pushed to the
// Cmd FIFO. This will prevent multiple push of the same Command as well as
// keeping the MI-side Valid signal if the Allow Cmd requirement has been
// updated to disable furter Commands (I.e. it is made sure that the SI-side
// Command has been forwarded to both Cmd FIFO and MI-side).
//
// It is allowed to continue pushing new commands as long as
// * There is room in the queue(s)
// * The ID is the same as previously queued. Since data is not reordered
// for the same ID it is always OK to let them proceed.
// Or, if no split transaction is ongoing any ID can be allowed.
//
/////////////////////////////////////////////////////////////////////////////
// Keep track of current ID in queue.
always @ (posedge ACLK) begin
if (ARESET) begin
queue_id <= {C_AXI_ID_WIDTH{1'b0}};
multiple_id_non_split <= 1'b0;
split_in_progress <= 1'b0;
end else begin
if ( cmd_push ) begin
// Store ID (it will be matching ID or a "new beginning").
queue_id <= S_AXI_AID_Q;
end
if ( no_cmd & no_b_cmd ) begin
multiple_id_non_split <= 1'b0;
end else if ( cmd_push & allow_non_split_cmd & ~id_match ) begin
multiple_id_non_split <= 1'b1;
end
if ( no_cmd & no_b_cmd ) begin
split_in_progress <= 1'b0;
end else if ( cmd_push & allow_split_cmd ) begin
split_in_progress <= 1'b1;
end
end
end
// Determine if the command FIFOs are empty.
assign no_cmd = almost_empty & cmd_ready | cmd_empty;
assign no_b_cmd = almost_b_empty & cmd_b_ready | cmd_b_empty;
// Check ID to make sure this command is allowed.
assign id_match = ( C_SINGLE_THREAD == 0 ) | ( queue_id == S_AXI_AID_Q);
assign cmd_id_check = (cmd_empty & cmd_b_empty) | ( id_match & (~cmd_empty | ~cmd_b_empty) );
// Command type affects possibility to push immediately or wait.
assign allow_split_cmd = need_to_split_q & cmd_id_check & ~multiple_id_non_split;
assign allow_non_split_cmd = ~need_to_split_q & (cmd_id_check | ~split_in_progress);
assign allow_this_cmd = allow_split_cmd | allow_non_split_cmd | ( C_SINGLE_THREAD == 0 );
// Check if it is allowed to push more commands.
assign allow_new_cmd = (~cmd_full & ~cmd_b_full & allow_this_cmd) |
cmd_push_block;
// Push new command when allowed and MI-side is able to receive the command.
assign cmd_push = M_AXI_AVALID_I & ~cmd_push_block;
assign cmd_b_push = M_AXI_AVALID_I & ~cmd_b_push_block & (C_AXI_CHANNEL == 0);
// Block furter push until command has been forwarded to MI-side.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_push_block <= 1'b0;
end else begin
if ( pushed_new_cmd ) begin
cmd_push_block <= 1'b0;
end else if ( cmd_push & mi_stalling ) begin
cmd_push_block <= 1'b1;
end
end
end
// Block furter push until command has been forwarded to MI-side.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_b_push_block <= 1'b0;
end else begin
if ( S_AXI_AREADY_I ) begin
cmd_b_push_block <= 1'b0;
end else if ( cmd_b_push ) begin
cmd_b_push_block <= 1'b1;
end
end
end
// Acknowledge command when we can push it into queue (and forward it).
assign pushed_new_cmd = M_AXI_AVALID_I & M_AXI_AREADY_I;
/////////////////////////////////////////////////////////////////////////////
// Command Queue (W/R):
//
// Instantiate a FIFO as the queue and adjust the control signals.
//
// The features from Command FIFO can be reduced depending on configuration:
// Read Channel only need the split information.
// Write Channel always require ID information. When bursts are supported
// Split and Length information is also used.
//
/////////////////////////////////////////////////////////////////////////////
// Instantiated queue.
generate
if ( C_AXI_CHANNEL == 1 && C_SUPPORT_SPLITTING == 1 && C_SUPPORT_BURSTS == 1 ) begin : USE_R_CHANNEL
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(1),
.C_FIFO_TYPE("lut")
)
cmd_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_split_i}),
.S_VALID(cmd_push),
.S_READY(s_ready),
.M_MESG({cmd_split}),
.M_VALID(cmd_valid),
.M_READY(cmd_ready)
);
assign cmd_id = {C_AXI_ID_WIDTH{1'b0}};
assign cmd_length = 4'b0;
end else if (C_SUPPORT_BURSTS == 1) begin : USE_BURSTS
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(C_AXI_ID_WIDTH+4),
.C_FIFO_TYPE("lut")
)
cmd_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_id_i, cmd_length_i}),
.S_VALID(cmd_push),
.S_READY(s_ready),
.M_MESG({cmd_id, cmd_length}),
.M_VALID(cmd_valid),
.M_READY(cmd_ready)
);
assign cmd_split = 1'b0;
end else begin : NO_BURSTS
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(C_AXI_ID_WIDTH),
.C_FIFO_TYPE("lut")
)
cmd_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_id_i}),
.S_VALID(cmd_push),
.S_READY(s_ready),
.M_MESG({cmd_id}),
.M_VALID(cmd_valid),
.M_READY(cmd_ready)
);
assign cmd_split = 1'b0;
assign cmd_length = 4'b0;
end
endgenerate
// Queue is concidered full when not ready.
assign cmd_full = ~s_ready;
// Queue is empty when no data at output port.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_empty <= 1'b1;
cmd_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end else begin
if ( cmd_push & ~cmd_ready ) begin
// Push only => Increase depth.
cmd_depth <= cmd_depth + 1'b1;
cmd_empty <= 1'b0;
end else if ( ~cmd_push & cmd_ready ) begin
// Pop only => Decrease depth.
cmd_depth <= cmd_depth - 1'b1;
cmd_empty <= almost_empty;
end
end
end
assign almost_empty = ( cmd_depth == 1 );
/////////////////////////////////////////////////////////////////////////////
// Command Queue (B):
//
// Add command queue for B channel only when it is AW channel and both burst
// and splitting is supported.
//
// When turned off the command appears always empty.
//
/////////////////////////////////////////////////////////////////////////////
// Instantiated queue.
generate
if ( C_AXI_CHANNEL == 0 && C_SUPPORT_SPLITTING == 1 && C_SUPPORT_BURSTS == 1 ) begin : USE_B_CHANNEL
wire cmd_b_valid_i;
wire s_b_ready;
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(1+4),
.C_FIFO_TYPE("lut")
)
cmd_b_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_b_split_i, cmd_b_repeat_i}),
.S_VALID(cmd_b_push),
.S_READY(s_b_ready),
.M_MESG({cmd_b_split, cmd_b_repeat}),
.M_VALID(cmd_b_valid_i),
.M_READY(cmd_b_ready)
);
// Queue is concidered full when not ready.
assign cmd_b_full = ~s_b_ready;
// Queue is empty when no data at output port.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_b_empty <= 1'b1;
cmd_b_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end else begin
if ( cmd_b_push & ~cmd_b_ready ) begin
// Push only => Increase depth.
cmd_b_depth <= cmd_b_depth + 1'b1;
cmd_b_empty <= 1'b0;
end else if ( ~cmd_b_push & cmd_b_ready ) begin
// Pop only => Decrease depth.
cmd_b_depth <= cmd_b_depth - 1'b1;
cmd_b_empty <= ( cmd_b_depth == 1 );
end
end
end
assign almost_b_empty = ( cmd_b_depth == 1 );
// Assign external signal.
assign cmd_b_valid = cmd_b_valid_i;
end else begin : NO_B_CHANNEL
// Assign external command signals.
assign cmd_b_valid = 1'b0;
assign cmd_b_split = 1'b0;
assign cmd_b_repeat = 4'b0;
// Assign internal command FIFO signals.
assign cmd_b_full = 1'b0;
assign almost_b_empty = 1'b0;
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_b_empty <= 1'b1;
cmd_b_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end else begin
// Constant FF due to ModelSim behavior.
cmd_b_empty <= 1'b1;
cmd_b_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end
end
end
endgenerate
/////////////////////////////////////////////////////////////////////////////
// MI-side output handling
//
/////////////////////////////////////////////////////////////////////////////
assign M_AXI_AID = M_AXI_AID_I;
assign M_AXI_AADDR = M_AXI_AADDR_I;
assign M_AXI_ALEN = M_AXI_ALEN_I;
assign M_AXI_ASIZE = M_AXI_ASIZE_I;
assign M_AXI_ABURST = M_AXI_ABURST_I;
assign M_AXI_ALOCK = M_AXI_ALOCK_I;
assign M_AXI_ACACHE = M_AXI_ACACHE_I;
assign M_AXI_APROT = M_AXI_APROT_I;
assign M_AXI_AQOS = M_AXI_AQOS_I;
assign M_AXI_AUSER = M_AXI_AUSER_I;
assign M_AXI_AVALID = M_AXI_AVALID_I;
assign M_AXI_AREADY_I = M_AXI_AREADY;
endmodule
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: Address AXI3 Slave Converter
//
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// a_axi3_conv
// axic_fifo
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_a_axi3_conv #
(
parameter C_FAMILY = "none",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_USER_SIGNALS = 0,
parameter integer C_AXI_AUSER_WIDTH = 1,
parameter integer C_AXI_CHANNEL = 0,
// 0 = AXI AW Channel.
// 1 = AXI AR Channel.
parameter integer C_SUPPORT_SPLITTING = 1,
// Implement transaction splitting logic.
// Disabled whan all connected masters are AXI3 and have same or narrower data width.
parameter integer C_SUPPORT_BURSTS = 1,
// Disabled when all connected masters are AxiLite,
// allowing logic to be simplified.
parameter integer C_SINGLE_THREAD = 1
// 0 = Ignore ID when propagating transactions (assume all responses are in order).
// 1 = Enforce single-threading (one ID at a time) when any outstanding or
// requested transaction requires splitting.
// While no split is ongoing any new non-split transaction will pass immediately regardless
// off ID.
// A split transaction will stall if there are multiple ID (non-split) transactions
// ongoing, once it has been forwarded only transactions with the same ID is allowed
// (split or not) until all ongoing split transactios has been completed.
)
(
// System Signals
input wire ACLK,
input wire ARESET,
// Command Interface (W/R)
output wire cmd_valid,
output wire cmd_split,
output wire [C_AXI_ID_WIDTH-1:0] cmd_id,
output wire [4-1:0] cmd_length,
input wire cmd_ready,
// Command Interface (B)
output wire cmd_b_valid,
output wire cmd_b_split,
output wire [4-1:0] cmd_b_repeat,
input wire cmd_b_ready,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AADDR,
input wire [8-1:0] S_AXI_ALEN,
input wire [3-1:0] S_AXI_ASIZE,
input wire [2-1:0] S_AXI_ABURST,
input wire [1-1:0] S_AXI_ALOCK,
input wire [4-1:0] S_AXI_ACACHE,
input wire [3-1:0] S_AXI_APROT,
input wire [4-1:0] S_AXI_AQOS,
input wire [C_AXI_AUSER_WIDTH-1:0] S_AXI_AUSER,
input wire S_AXI_AVALID,
output wire S_AXI_AREADY,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] M_AXI_AID,
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AADDR,
output wire [4-1:0] M_AXI_ALEN,
output wire [3-1:0] M_AXI_ASIZE,
output wire [2-1:0] M_AXI_ABURST,
output wire [2-1:0] M_AXI_ALOCK,
output wire [4-1:0] M_AXI_ACACHE,
output wire [3-1:0] M_AXI_APROT,
output wire [4-1:0] M_AXI_AQOS,
output wire [C_AXI_AUSER_WIDTH-1:0] M_AXI_AUSER,
output wire M_AXI_AVALID,
input wire M_AXI_AREADY
);
/////////////////////////////////////////////////////////////////////////////
// Variables for generating parameter controlled instances.
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Local params
/////////////////////////////////////////////////////////////////////////////
// Constants for burst types.
localparam [2-1:0] C_FIX_BURST = 2'b00;
localparam [2-1:0] C_INCR_BURST = 2'b01;
localparam [2-1:0] C_WRAP_BURST = 2'b10;
// Depth for command FIFO.
localparam integer C_FIFO_DEPTH_LOG = 5;
// Constants used to generate size mask.
localparam [C_AXI_ADDR_WIDTH+8-1:0] C_SIZE_MASK = {{C_AXI_ADDR_WIDTH{1'b1}}, 8'b0000_0000};
/////////////////////////////////////////////////////////////////////////////
// Functions
/////////////////////////////////////////////////////////////////////////////
/////////////////////////////////////////////////////////////////////////////
// Internal signals
/////////////////////////////////////////////////////////////////////////////
// Access decoding related signals.
wire access_is_incr;
wire [4-1:0] num_transactions;
wire incr_need_to_split;
reg [C_AXI_ADDR_WIDTH-1:0] next_mi_addr;
reg split_ongoing;
reg [4-1:0] pushed_commands;
reg [16-1:0] addr_step;
reg [16-1:0] first_step;
wire [8-1:0] first_beats;
reg [C_AXI_ADDR_WIDTH-1:0] size_mask;
// Access decoding related signals for internal pipestage.
reg access_is_incr_q;
reg incr_need_to_split_q;
wire need_to_split_q;
reg [4-1:0] num_transactions_q;
reg [16-1:0] addr_step_q;
reg [16-1:0] first_step_q;
reg [C_AXI_ADDR_WIDTH-1:0] size_mask_q;
// Command buffer help signals.
reg [C_FIFO_DEPTH_LOG:0] cmd_depth;
reg cmd_empty;
reg [C_AXI_ID_WIDTH-1:0] queue_id;
wire id_match;
wire cmd_id_check;
wire s_ready;
wire cmd_full;
wire allow_this_cmd;
wire allow_new_cmd;
wire cmd_push;
reg cmd_push_block;
reg [C_FIFO_DEPTH_LOG:0] cmd_b_depth;
reg cmd_b_empty;
wire cmd_b_full;
wire cmd_b_push;
reg cmd_b_push_block;
wire pushed_new_cmd;
wire last_incr_split;
wire last_split;
wire first_split;
wire no_cmd;
wire allow_split_cmd;
wire almost_empty;
wire no_b_cmd;
wire allow_non_split_cmd;
wire almost_b_empty;
reg multiple_id_non_split;
reg split_in_progress;
// Internal Command Interface signals (W/R).
wire cmd_split_i;
wire [C_AXI_ID_WIDTH-1:0] cmd_id_i;
reg [4-1:0] cmd_length_i;
// Internal Command Interface signals (B).
wire cmd_b_split_i;
wire [4-1:0] cmd_b_repeat_i;
// Throttling help signals.
wire mi_stalling;
reg command_ongoing;
// Internal SI-side signals.
reg [C_AXI_ID_WIDTH-1:0] S_AXI_AID_Q;
reg [C_AXI_ADDR_WIDTH-1:0] S_AXI_AADDR_Q;
reg [8-1:0] S_AXI_ALEN_Q;
reg [3-1:0] S_AXI_ASIZE_Q;
reg [2-1:0] S_AXI_ABURST_Q;
reg [2-1:0] S_AXI_ALOCK_Q;
reg [4-1:0] S_AXI_ACACHE_Q;
reg [3-1:0] S_AXI_APROT_Q;
reg [4-1:0] S_AXI_AQOS_Q;
reg [C_AXI_AUSER_WIDTH-1:0] S_AXI_AUSER_Q;
reg S_AXI_AREADY_I;
// Internal MI-side signals.
wire [C_AXI_ID_WIDTH-1:0] M_AXI_AID_I;
reg [C_AXI_ADDR_WIDTH-1:0] M_AXI_AADDR_I;
reg [8-1:0] M_AXI_ALEN_I;
wire [3-1:0] M_AXI_ASIZE_I;
wire [2-1:0] M_AXI_ABURST_I;
reg [2-1:0] M_AXI_ALOCK_I;
wire [4-1:0] M_AXI_ACACHE_I;
wire [3-1:0] M_AXI_APROT_I;
wire [4-1:0] M_AXI_AQOS_I;
wire [C_AXI_AUSER_WIDTH-1:0] M_AXI_AUSER_I;
wire M_AXI_AVALID_I;
wire M_AXI_AREADY_I;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ARESET};
end
/////////////////////////////////////////////////////////////////////////////
// Capture SI-Side signals.
//
/////////////////////////////////////////////////////////////////////////////
// Register SI-Side signals.
always @ (posedge ACLK) begin
if ( ARESET ) begin
S_AXI_AID_Q <= {C_AXI_ID_WIDTH{1'b0}};
S_AXI_AADDR_Q <= {C_AXI_ADDR_WIDTH{1'b0}};
S_AXI_ALEN_Q <= 8'b0;
S_AXI_ASIZE_Q <= 3'b0;
S_AXI_ABURST_Q <= 2'b0;
S_AXI_ALOCK_Q <= 2'b0;
S_AXI_ACACHE_Q <= 4'b0;
S_AXI_APROT_Q <= 3'b0;
S_AXI_AQOS_Q <= 4'b0;
S_AXI_AUSER_Q <= {C_AXI_AUSER_WIDTH{1'b0}};
end else begin
if ( S_AXI_AREADY_I ) begin
S_AXI_AID_Q <= S_AXI_AID;
S_AXI_AADDR_Q <= S_AXI_AADDR;
S_AXI_ALEN_Q <= S_AXI_ALEN;
S_AXI_ASIZE_Q <= S_AXI_ASIZE;
S_AXI_ABURST_Q <= S_AXI_ABURST;
S_AXI_ALOCK_Q <= S_AXI_ALOCK;
S_AXI_ACACHE_Q <= S_AXI_ACACHE;
S_AXI_APROT_Q <= S_AXI_APROT;
S_AXI_AQOS_Q <= S_AXI_AQOS;
S_AXI_AUSER_Q <= S_AXI_AUSER;
end
end
end
/////////////////////////////////////////////////////////////////////////////
// Decode the Incoming Transaction.
//
// Extract transaction type and the number of splits that may be needed.
//
// Calculate the step size so that the address for each part of a split can
// can be calculated.
//
/////////////////////////////////////////////////////////////////////////////
// Transaction burst type.
assign access_is_incr = ( S_AXI_ABURST == C_INCR_BURST );
// Get number of transactions for split INCR.
assign num_transactions = S_AXI_ALEN[4 +: 4];
assign first_beats = {3'b0, S_AXI_ALEN[0 +: 4]} + 7'b01;
// Generate address increment of first split transaction.
always @ *
begin
case (S_AXI_ASIZE)
3'b000: first_step = first_beats << 0;
3'b001: first_step = first_beats << 1;
3'b010: first_step = first_beats << 2;
3'b011: first_step = first_beats << 3;
3'b100: first_step = first_beats << 4;
3'b101: first_step = first_beats << 5;
3'b110: first_step = first_beats << 6;
3'b111: first_step = first_beats << 7;
endcase
end
// Generate address increment for remaining split transactions.
always @ *
begin
case (S_AXI_ASIZE)
3'b000: addr_step = 16'h0010;
3'b001: addr_step = 16'h0020;
3'b010: addr_step = 16'h0040;
3'b011: addr_step = 16'h0080;
3'b100: addr_step = 16'h0100;
3'b101: addr_step = 16'h0200;
3'b110: addr_step = 16'h0400;
3'b111: addr_step = 16'h0800;
endcase
end
// Generate address mask bits to remove split transaction unalignment.
always @ *
begin
case (S_AXI_ASIZE)
3'b000: size_mask = C_SIZE_MASK[8 +: C_AXI_ADDR_WIDTH];
3'b001: size_mask = C_SIZE_MASK[7 +: C_AXI_ADDR_WIDTH];
3'b010: size_mask = C_SIZE_MASK[6 +: C_AXI_ADDR_WIDTH];
3'b011: size_mask = C_SIZE_MASK[5 +: C_AXI_ADDR_WIDTH];
3'b100: size_mask = C_SIZE_MASK[4 +: C_AXI_ADDR_WIDTH];
3'b101: size_mask = C_SIZE_MASK[3 +: C_AXI_ADDR_WIDTH];
3'b110: size_mask = C_SIZE_MASK[2 +: C_AXI_ADDR_WIDTH];
3'b111: size_mask = C_SIZE_MASK[1 +: C_AXI_ADDR_WIDTH];
endcase
end
/////////////////////////////////////////////////////////////////////////////
// Transfer SI-Side signals to internal Pipeline Stage.
//
/////////////////////////////////////////////////////////////////////////////
always @ (posedge ACLK) begin
if ( ARESET ) begin
access_is_incr_q <= 1'b0;
incr_need_to_split_q <= 1'b0;
num_transactions_q <= 4'b0;
addr_step_q <= 16'b0;
first_step_q <= 16'b0;
size_mask_q <= {C_AXI_ADDR_WIDTH{1'b0}};
end else begin
if ( S_AXI_AREADY_I ) begin
access_is_incr_q <= access_is_incr;
incr_need_to_split_q <= incr_need_to_split;
num_transactions_q <= num_transactions;
addr_step_q <= addr_step;
first_step_q <= first_step;
size_mask_q <= size_mask;
end
end
end
/////////////////////////////////////////////////////////////////////////////
// Generate Command Information.
//
// Detect if current transation needs to be split, and keep track of all
// the generated split transactions.
//
//
/////////////////////////////////////////////////////////////////////////////
// Detect when INCR must be split.
assign incr_need_to_split = access_is_incr & ( num_transactions != 0 ) &
( C_SUPPORT_SPLITTING == 1 ) &
( C_SUPPORT_BURSTS == 1 );
// Detect when a command has to be split.
assign need_to_split_q = incr_need_to_split_q;
// Handle progress of split transactions.
always @ (posedge ACLK) begin
if ( ARESET ) begin
split_ongoing <= 1'b0;
end else begin
if ( pushed_new_cmd ) begin
split_ongoing <= need_to_split_q & ~last_split;
end
end
end
// Keep track of number of transactions generated.
always @ (posedge ACLK) begin
if ( ARESET ) begin
pushed_commands <= 4'b0;
end else begin
if ( S_AXI_AREADY_I ) begin
pushed_commands <= 4'b0;
end else if ( pushed_new_cmd ) begin
pushed_commands <= pushed_commands + 4'b1;
end
end
end
// Detect last part of a command, split or not.
assign last_incr_split = access_is_incr_q & ( num_transactions_q == pushed_commands );
assign last_split = last_incr_split | ~access_is_incr_q |
( C_SUPPORT_SPLITTING == 0 ) |
( C_SUPPORT_BURSTS == 0 );
assign first_split = (pushed_commands == 4'b0);
// Calculate base for next address.
always @ (posedge ACLK) begin
if ( ARESET ) begin
next_mi_addr = {C_AXI_ADDR_WIDTH{1'b0}};
end else if ( pushed_new_cmd ) begin
next_mi_addr = M_AXI_AADDR_I + (first_split ? first_step_q : addr_step_q);
end
end
/////////////////////////////////////////////////////////////////////////////
// Translating Transaction.
//
// Set Split transaction information on all part except last for a transaction
// that needs splitting.
// The B Channel will only get one command for a Split transaction and in
// the Split bflag will be set in that case.
//
// The AWID is extracted and applied to all commands generated for the current
// incomming SI-Side transaction.
//
// The address is increased for each part of a Split transaction, the amount
// depends on the siSIZE for the transaction.
//
// The length has to be changed for Split transactions. All part except tha
// last one will have 0xF, the last one uses the 4 lsb bits from the SI-side
// transaction as length.
//
// Non-Split has untouched address and length information.
//
// Exclusive access are diasabled for a Split transaction because it is not
// possible to guarantee concistency between all the parts.
//
/////////////////////////////////////////////////////////////////////////////
// Assign Split signals.
assign cmd_split_i = need_to_split_q & ~last_split;
assign cmd_b_split_i = need_to_split_q & ~last_split;
// Copy AW ID to W.
assign cmd_id_i = S_AXI_AID_Q;
// Set B Responses to merge.
assign cmd_b_repeat_i = num_transactions_q;
// Select new size or remaining size.
always @ *
begin
if ( split_ongoing & access_is_incr_q ) begin
M_AXI_AADDR_I = next_mi_addr & size_mask_q;
end else begin
M_AXI_AADDR_I = S_AXI_AADDR_Q;
end
end
// Generate the base length for each transaction.
always @ *
begin
if ( first_split | ~need_to_split_q ) begin
M_AXI_ALEN_I = S_AXI_ALEN_Q[0 +: 4];
cmd_length_i = S_AXI_ALEN_Q[0 +: 4];
end else begin
M_AXI_ALEN_I = 4'hF;
cmd_length_i = 4'hF;
end
end
// Kill Exclusive for Split transactions.
always @ *
begin
if ( need_to_split_q ) begin
M_AXI_ALOCK_I = 2'b00;
end else begin
M_AXI_ALOCK_I = {1'b0, S_AXI_ALOCK_Q};
end
end
/////////////////////////////////////////////////////////////////////////////
// Forward the command to the MI-side interface.
//
// It is determined that this is an allowed command/access when there is
// room in the command queue (and it passes ID and Split checks as required).
//
/////////////////////////////////////////////////////////////////////////////
// Move SI-side transaction to internal pipe stage.
always @ (posedge ACLK) begin
if (ARESET) begin
command_ongoing <= 1'b0;
S_AXI_AREADY_I <= 1'b0;
end else begin
if (areset_d == 2'b10) begin
S_AXI_AREADY_I <= 1'b1;
end else begin
if ( S_AXI_AVALID & S_AXI_AREADY_I ) begin
command_ongoing <= 1'b1;
S_AXI_AREADY_I <= 1'b0;
end else if ( pushed_new_cmd & last_split ) begin
command_ongoing <= 1'b0;
S_AXI_AREADY_I <= 1'b1;
end
end
end
end
// Generate ready signal.
assign S_AXI_AREADY = S_AXI_AREADY_I;
// Only allowed to forward translated command when command queue is ok with it.
assign M_AXI_AVALID_I = allow_new_cmd & command_ongoing;
// Detect when MI-side is stalling.
assign mi_stalling = M_AXI_AVALID_I & ~M_AXI_AREADY_I;
/////////////////////////////////////////////////////////////////////////////
// Simple transfer of paramters that doesn't need to be adjusted.
//
// ID - Transaction still recognized with the same ID.
// CACHE - No need to change the chache features. Even if the modyfiable
// bit is overridden (forcefully) there is no need to let downstream
// component beleive it is ok to modify it further.
// PROT - Security level of access is not changed when upsizing.
// QOS - Quality of Service is static 0.
// USER - User bits remains the same.
//
/////////////////////////////////////////////////////////////////////////////
assign M_AXI_AID_I = S_AXI_AID_Q;
assign M_AXI_ASIZE_I = S_AXI_ASIZE_Q;
assign M_AXI_ABURST_I = S_AXI_ABURST_Q;
assign M_AXI_ACACHE_I = S_AXI_ACACHE_Q;
assign M_AXI_APROT_I = S_AXI_APROT_Q;
assign M_AXI_AQOS_I = S_AXI_AQOS_Q;
assign M_AXI_AUSER_I = ( C_AXI_SUPPORTS_USER_SIGNALS ) ? S_AXI_AUSER_Q : {C_AXI_AUSER_WIDTH{1'b0}};
/////////////////////////////////////////////////////////////////////////////
// Control command queue to W/R channel.
//
// Commands can be pushed into the Cmd FIFO even if MI-side is stalling.
// A flag is set if MI-side is stalling when Command is pushed to the
// Cmd FIFO. This will prevent multiple push of the same Command as well as
// keeping the MI-side Valid signal if the Allow Cmd requirement has been
// updated to disable furter Commands (I.e. it is made sure that the SI-side
// Command has been forwarded to both Cmd FIFO and MI-side).
//
// It is allowed to continue pushing new commands as long as
// * There is room in the queue(s)
// * The ID is the same as previously queued. Since data is not reordered
// for the same ID it is always OK to let them proceed.
// Or, if no split transaction is ongoing any ID can be allowed.
//
/////////////////////////////////////////////////////////////////////////////
// Keep track of current ID in queue.
always @ (posedge ACLK) begin
if (ARESET) begin
queue_id <= {C_AXI_ID_WIDTH{1'b0}};
multiple_id_non_split <= 1'b0;
split_in_progress <= 1'b0;
end else begin
if ( cmd_push ) begin
// Store ID (it will be matching ID or a "new beginning").
queue_id <= S_AXI_AID_Q;
end
if ( no_cmd & no_b_cmd ) begin
multiple_id_non_split <= 1'b0;
end else if ( cmd_push & allow_non_split_cmd & ~id_match ) begin
multiple_id_non_split <= 1'b1;
end
if ( no_cmd & no_b_cmd ) begin
split_in_progress <= 1'b0;
end else if ( cmd_push & allow_split_cmd ) begin
split_in_progress <= 1'b1;
end
end
end
// Determine if the command FIFOs are empty.
assign no_cmd = almost_empty & cmd_ready | cmd_empty;
assign no_b_cmd = almost_b_empty & cmd_b_ready | cmd_b_empty;
// Check ID to make sure this command is allowed.
assign id_match = ( C_SINGLE_THREAD == 0 ) | ( queue_id == S_AXI_AID_Q);
assign cmd_id_check = (cmd_empty & cmd_b_empty) | ( id_match & (~cmd_empty | ~cmd_b_empty) );
// Command type affects possibility to push immediately or wait.
assign allow_split_cmd = need_to_split_q & cmd_id_check & ~multiple_id_non_split;
assign allow_non_split_cmd = ~need_to_split_q & (cmd_id_check | ~split_in_progress);
assign allow_this_cmd = allow_split_cmd | allow_non_split_cmd | ( C_SINGLE_THREAD == 0 );
// Check if it is allowed to push more commands.
assign allow_new_cmd = (~cmd_full & ~cmd_b_full & allow_this_cmd) |
cmd_push_block;
// Push new command when allowed and MI-side is able to receive the command.
assign cmd_push = M_AXI_AVALID_I & ~cmd_push_block;
assign cmd_b_push = M_AXI_AVALID_I & ~cmd_b_push_block & (C_AXI_CHANNEL == 0);
// Block furter push until command has been forwarded to MI-side.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_push_block <= 1'b0;
end else begin
if ( pushed_new_cmd ) begin
cmd_push_block <= 1'b0;
end else if ( cmd_push & mi_stalling ) begin
cmd_push_block <= 1'b1;
end
end
end
// Block furter push until command has been forwarded to MI-side.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_b_push_block <= 1'b0;
end else begin
if ( S_AXI_AREADY_I ) begin
cmd_b_push_block <= 1'b0;
end else if ( cmd_b_push ) begin
cmd_b_push_block <= 1'b1;
end
end
end
// Acknowledge command when we can push it into queue (and forward it).
assign pushed_new_cmd = M_AXI_AVALID_I & M_AXI_AREADY_I;
/////////////////////////////////////////////////////////////////////////////
// Command Queue (W/R):
//
// Instantiate a FIFO as the queue and adjust the control signals.
//
// The features from Command FIFO can be reduced depending on configuration:
// Read Channel only need the split information.
// Write Channel always require ID information. When bursts are supported
// Split and Length information is also used.
//
/////////////////////////////////////////////////////////////////////////////
// Instantiated queue.
generate
if ( C_AXI_CHANNEL == 1 && C_SUPPORT_SPLITTING == 1 && C_SUPPORT_BURSTS == 1 ) begin : USE_R_CHANNEL
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(1),
.C_FIFO_TYPE("lut")
)
cmd_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_split_i}),
.S_VALID(cmd_push),
.S_READY(s_ready),
.M_MESG({cmd_split}),
.M_VALID(cmd_valid),
.M_READY(cmd_ready)
);
assign cmd_id = {C_AXI_ID_WIDTH{1'b0}};
assign cmd_length = 4'b0;
end else if (C_SUPPORT_BURSTS == 1) begin : USE_BURSTS
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(C_AXI_ID_WIDTH+4),
.C_FIFO_TYPE("lut")
)
cmd_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_id_i, cmd_length_i}),
.S_VALID(cmd_push),
.S_READY(s_ready),
.M_MESG({cmd_id, cmd_length}),
.M_VALID(cmd_valid),
.M_READY(cmd_ready)
);
assign cmd_split = 1'b0;
end else begin : NO_BURSTS
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(C_AXI_ID_WIDTH),
.C_FIFO_TYPE("lut")
)
cmd_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_id_i}),
.S_VALID(cmd_push),
.S_READY(s_ready),
.M_MESG({cmd_id}),
.M_VALID(cmd_valid),
.M_READY(cmd_ready)
);
assign cmd_split = 1'b0;
assign cmd_length = 4'b0;
end
endgenerate
// Queue is concidered full when not ready.
assign cmd_full = ~s_ready;
// Queue is empty when no data at output port.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_empty <= 1'b1;
cmd_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end else begin
if ( cmd_push & ~cmd_ready ) begin
// Push only => Increase depth.
cmd_depth <= cmd_depth + 1'b1;
cmd_empty <= 1'b0;
end else if ( ~cmd_push & cmd_ready ) begin
// Pop only => Decrease depth.
cmd_depth <= cmd_depth - 1'b1;
cmd_empty <= almost_empty;
end
end
end
assign almost_empty = ( cmd_depth == 1 );
/////////////////////////////////////////////////////////////////////////////
// Command Queue (B):
//
// Add command queue for B channel only when it is AW channel and both burst
// and splitting is supported.
//
// When turned off the command appears always empty.
//
/////////////////////////////////////////////////////////////////////////////
// Instantiated queue.
generate
if ( C_AXI_CHANNEL == 0 && C_SUPPORT_SPLITTING == 1 && C_SUPPORT_BURSTS == 1 ) begin : USE_B_CHANNEL
wire cmd_b_valid_i;
wire s_b_ready;
axi_data_fifo_v2_1_axic_fifo #
(
.C_FAMILY(C_FAMILY),
.C_FIFO_DEPTH_LOG(C_FIFO_DEPTH_LOG),
.C_FIFO_WIDTH(1+4),
.C_FIFO_TYPE("lut")
)
cmd_b_queue
(
.ACLK(ACLK),
.ARESET(ARESET),
.S_MESG({cmd_b_split_i, cmd_b_repeat_i}),
.S_VALID(cmd_b_push),
.S_READY(s_b_ready),
.M_MESG({cmd_b_split, cmd_b_repeat}),
.M_VALID(cmd_b_valid_i),
.M_READY(cmd_b_ready)
);
// Queue is concidered full when not ready.
assign cmd_b_full = ~s_b_ready;
// Queue is empty when no data at output port.
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_b_empty <= 1'b1;
cmd_b_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end else begin
if ( cmd_b_push & ~cmd_b_ready ) begin
// Push only => Increase depth.
cmd_b_depth <= cmd_b_depth + 1'b1;
cmd_b_empty <= 1'b0;
end else if ( ~cmd_b_push & cmd_b_ready ) begin
// Pop only => Decrease depth.
cmd_b_depth <= cmd_b_depth - 1'b1;
cmd_b_empty <= ( cmd_b_depth == 1 );
end
end
end
assign almost_b_empty = ( cmd_b_depth == 1 );
// Assign external signal.
assign cmd_b_valid = cmd_b_valid_i;
end else begin : NO_B_CHANNEL
// Assign external command signals.
assign cmd_b_valid = 1'b0;
assign cmd_b_split = 1'b0;
assign cmd_b_repeat = 4'b0;
// Assign internal command FIFO signals.
assign cmd_b_full = 1'b0;
assign almost_b_empty = 1'b0;
always @ (posedge ACLK) begin
if (ARESET) begin
cmd_b_empty <= 1'b1;
cmd_b_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end else begin
// Constant FF due to ModelSim behavior.
cmd_b_empty <= 1'b1;
cmd_b_depth <= {C_FIFO_DEPTH_LOG+1{1'b0}};
end
end
end
endgenerate
/////////////////////////////////////////////////////////////////////////////
// MI-side output handling
//
/////////////////////////////////////////////////////////////////////////////
assign M_AXI_AID = M_AXI_AID_I;
assign M_AXI_AADDR = M_AXI_AADDR_I;
assign M_AXI_ALEN = M_AXI_ALEN_I;
assign M_AXI_ASIZE = M_AXI_ASIZE_I;
assign M_AXI_ABURST = M_AXI_ABURST_I;
assign M_AXI_ALOCK = M_AXI_ALOCK_I;
assign M_AXI_ACACHE = M_AXI_ACACHE_I;
assign M_AXI_APROT = M_AXI_APROT_I;
assign M_AXI_AQOS = M_AXI_AQOS_I;
assign M_AXI_AUSER = M_AXI_AUSER_I;
assign M_AXI_AVALID = M_AXI_AVALID_I;
assign M_AXI_AREADY_I = M_AXI_AREADY;
endmodule
|
// This is a component of pluto_servo, a PWM servo driver and quadrature
// counter for emc2
// Copyright 2006 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1507 USA
module quad(clk, A, B, Z, zr, out);
parameter W=14;
input clk, A, B, Z, zr;
reg [(W-1):0] c, i; reg zl;
output [2*W:0] out = { zl, i, c };
// reg [(W-1):0] c, i; reg zl;
reg [2:0] Ad, Bd;
reg [2:0] Zc;
always @(posedge clk) Ad <= {Ad[1:0], A};
always @(posedge clk) Bd <= {Bd[1:0], B};
wire good_one = &Zc;
wire good_zero = ~|Zc;
reg last_good;
wire index_pulse = good_one && ! last_good;
wire count_enable = Ad[1] ^ Ad[2] ^ Bd[1] ^ Bd[2];
wire count_direction = Ad[1] ^ Bd[2];
always @(posedge clk)
begin
if(Z && !good_one) Zc <= Zc + 2'b1;
else if(!good_zero) Zc <= Zc - 2'b1;
if(good_one) last_good <= 1;
else if(good_zero) last_good <= 0;
if(count_enable)
begin
if(count_direction) c <= c + 1'd1;
else c <= c - 1'd1;
end
if(index_pulse) begin
i <= c;
zl <= 1;
end else if(zr) begin
zl <= 0;
end
end
endmodule
|
// This is a component of pluto_servo, a PWM servo driver and quadrature
// counter for emc2
// Copyright 2006 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1507 USA
module quad(clk, A, B, Z, zr, out);
parameter W=14;
input clk, A, B, Z, zr;
reg [(W-1):0] c, i; reg zl;
output [2*W:0] out = { zl, i, c };
// reg [(W-1):0] c, i; reg zl;
reg [2:0] Ad, Bd;
reg [2:0] Zc;
always @(posedge clk) Ad <= {Ad[1:0], A};
always @(posedge clk) Bd <= {Bd[1:0], B};
wire good_one = &Zc;
wire good_zero = ~|Zc;
reg last_good;
wire index_pulse = good_one && ! last_good;
wire count_enable = Ad[1] ^ Ad[2] ^ Bd[1] ^ Bd[2];
wire count_direction = Ad[1] ^ Bd[2];
always @(posedge clk)
begin
if(Z && !good_one) Zc <= Zc + 2'b1;
else if(!good_zero) Zc <= Zc - 2'b1;
if(good_one) last_good <= 1;
else if(good_zero) last_good <= 0;
if(count_enable)
begin
if(count_direction) c <= c + 1'd1;
else c <= c - 1'd1;
end
if(index_pulse) begin
i <= c;
zl <= 1;
end else if(zr) begin
zl <= 0;
end
end
endmodule
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_wr_cmd_fsm.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_wr_cmd_fsm (
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
output wire s_awready ,
input wire s_awvalid ,
output wire m_awvalid ,
input wire m_awready ,
// signal to increment to the next mc transaction
output wire next ,
// signal to the fsm there is another transaction required
input wire next_pending ,
// Write Data portion has completed or Read FIFO has a slot available (not
// full)
output wire b_push ,
input wire b_full ,
output wire a_push
);
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
// States
localparam SM_IDLE = 2'b00;
localparam SM_CMD_EN = 2'b01;
localparam SM_CMD_ACCEPTED = 2'b10;
localparam SM_DONE_WAIT = 2'b11;
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [1:0] state;
// synthesis attribute MAX_FANOUT of state is 20;
reg [1:0] next_state;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
///////////////////////////////////////////////////////////////////////////////
always @(posedge clk) begin
if (reset) begin
state <= SM_IDLE;
end else begin
state <= next_state;
end
end
// Next state transitions.
always @( * )
begin
next_state = state;
case (state)
SM_IDLE:
if (s_awvalid) begin
next_state = SM_CMD_EN;
end else
next_state = state;
SM_CMD_EN:
if (m_awready & next_pending)
next_state = SM_CMD_ACCEPTED;
else if (m_awready & ~next_pending & b_full)
next_state = SM_DONE_WAIT;
else if (m_awready & ~next_pending & ~b_full)
next_state = SM_IDLE;
else
next_state = state;
SM_CMD_ACCEPTED:
next_state = SM_CMD_EN;
SM_DONE_WAIT:
if (!b_full)
next_state = SM_IDLE;
else
next_state = state;
default:
next_state = SM_IDLE;
endcase
end
// Assign outputs based on current state.
assign m_awvalid = (state == SM_CMD_EN);
assign next = ((state == SM_CMD_ACCEPTED)
| (((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE))) ;
assign a_push = (state == SM_IDLE);
assign s_awready = ((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE);
assign b_push = ((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE);
endmodule
`default_nettype wire
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_wr_cmd_fsm.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_wr_cmd_fsm (
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
output wire s_awready ,
input wire s_awvalid ,
output wire m_awvalid ,
input wire m_awready ,
// signal to increment to the next mc transaction
output wire next ,
// signal to the fsm there is another transaction required
input wire next_pending ,
// Write Data portion has completed or Read FIFO has a slot available (not
// full)
output wire b_push ,
input wire b_full ,
output wire a_push
);
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
// States
localparam SM_IDLE = 2'b00;
localparam SM_CMD_EN = 2'b01;
localparam SM_CMD_ACCEPTED = 2'b10;
localparam SM_DONE_WAIT = 2'b11;
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [1:0] state;
// synthesis attribute MAX_FANOUT of state is 20;
reg [1:0] next_state;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
///////////////////////////////////////////////////////////////////////////////
always @(posedge clk) begin
if (reset) begin
state <= SM_IDLE;
end else begin
state <= next_state;
end
end
// Next state transitions.
always @( * )
begin
next_state = state;
case (state)
SM_IDLE:
if (s_awvalid) begin
next_state = SM_CMD_EN;
end else
next_state = state;
SM_CMD_EN:
if (m_awready & next_pending)
next_state = SM_CMD_ACCEPTED;
else if (m_awready & ~next_pending & b_full)
next_state = SM_DONE_WAIT;
else if (m_awready & ~next_pending & ~b_full)
next_state = SM_IDLE;
else
next_state = state;
SM_CMD_ACCEPTED:
next_state = SM_CMD_EN;
SM_DONE_WAIT:
if (!b_full)
next_state = SM_IDLE;
else
next_state = state;
default:
next_state = SM_IDLE;
endcase
end
// Assign outputs based on current state.
assign m_awvalid = (state == SM_CMD_EN);
assign next = ((state == SM_CMD_ACCEPTED)
| (((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE))) ;
assign a_push = (state == SM_IDLE);
assign s_awready = ((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE);
assign b_push = ((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE);
endmodule
`default_nettype wire
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_wr_cmd_fsm.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_wr_cmd_fsm (
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
output wire s_awready ,
input wire s_awvalid ,
output wire m_awvalid ,
input wire m_awready ,
// signal to increment to the next mc transaction
output wire next ,
// signal to the fsm there is another transaction required
input wire next_pending ,
// Write Data portion has completed or Read FIFO has a slot available (not
// full)
output wire b_push ,
input wire b_full ,
output wire a_push
);
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
// States
localparam SM_IDLE = 2'b00;
localparam SM_CMD_EN = 2'b01;
localparam SM_CMD_ACCEPTED = 2'b10;
localparam SM_DONE_WAIT = 2'b11;
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [1:0] state;
// synthesis attribute MAX_FANOUT of state is 20;
reg [1:0] next_state;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
///////////////////////////////////////////////////////////////////////////////
always @(posedge clk) begin
if (reset) begin
state <= SM_IDLE;
end else begin
state <= next_state;
end
end
// Next state transitions.
always @( * )
begin
next_state = state;
case (state)
SM_IDLE:
if (s_awvalid) begin
next_state = SM_CMD_EN;
end else
next_state = state;
SM_CMD_EN:
if (m_awready & next_pending)
next_state = SM_CMD_ACCEPTED;
else if (m_awready & ~next_pending & b_full)
next_state = SM_DONE_WAIT;
else if (m_awready & ~next_pending & ~b_full)
next_state = SM_IDLE;
else
next_state = state;
SM_CMD_ACCEPTED:
next_state = SM_CMD_EN;
SM_DONE_WAIT:
if (!b_full)
next_state = SM_IDLE;
else
next_state = state;
default:
next_state = SM_IDLE;
endcase
end
// Assign outputs based on current state.
assign m_awvalid = (state == SM_CMD_EN);
assign next = ((state == SM_CMD_ACCEPTED)
| (((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE))) ;
assign a_push = (state == SM_IDLE);
assign s_awready = ((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE);
assign b_push = ((state == SM_CMD_EN) | (state == SM_DONE_WAIT)) & (next_state == SM_IDLE);
endmodule
`default_nettype wire
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_incr_cmd.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_incr_cmd #
(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
// Width of AxADDR
// Range: 32.
parameter integer C_AXI_ADDR_WIDTH = 32
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
input wire [C_AXI_ADDR_WIDTH-1:0] axaddr ,
input wire [7:0] axlen ,
input wire [2:0] axsize ,
// axhandshake = axvalid & axready
input wire axhandshake ,
output wire [C_AXI_ADDR_WIDTH-1:0] cmd_byte_addr ,
// Connections to/from fsm module
// signal to increment to the next mc transaction
input wire next ,
// signal to the fsm there is another transaction required
output reg next_pending
);
////////////////////////////////////////////////////////////////////////////////
// Wire and register declarations
////////////////////////////////////////////////////////////////////////////////
reg sel_first;
reg [11:0] axaddr_incr;
reg [8:0] axlen_cnt;
reg next_pending_r;
wire [3:0] axsize_shift;
wire [11:0] axsize_mask;
localparam L_AXI_ADDR_LOW_BIT = (C_AXI_ADDR_WIDTH >= 12) ? 12 : 11;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// calculate cmd_byte_addr
generate
if (C_AXI_ADDR_WIDTH > 12) begin : ADDR_GT_4K
assign cmd_byte_addr = (sel_first) ? axaddr : {axaddr[C_AXI_ADDR_WIDTH-1:L_AXI_ADDR_LOW_BIT],axaddr_incr[11:0]};
end else begin : ADDR_4K
assign cmd_byte_addr = (sel_first) ? axaddr : axaddr_incr[11:0];
end
endgenerate
assign axsize_shift = (1 << axsize[1:0]);
assign axsize_mask = ~(axsize_shift - 1'b1);
// Incremented version of axaddr
always @(posedge clk) begin
if (sel_first) begin
if(~next) begin
axaddr_incr <= axaddr[11:0] & axsize_mask;
end else begin
axaddr_incr <= (axaddr[11:0] & axsize_mask) + axsize_shift;
end
end else if (next) begin
axaddr_incr <= axaddr_incr + axsize_shift;
end
end
always @(posedge clk) begin
if (axhandshake)begin
axlen_cnt <= axlen;
next_pending_r <= (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
axlen_cnt <= axlen_cnt - 1;
next_pending_r <= ((axlen_cnt - 1) >= 1);
end else begin
axlen_cnt <= 9'd0;
next_pending_r <= 1'b0;
end
end
end
always @( * ) begin
if (axhandshake)begin
next_pending = (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
next_pending = ((axlen_cnt - 1) >= 1);
end else begin
next_pending = 1'b0;
end
end else begin
next_pending = next_pending_r;
end
end
// last and ignore signals to data channel. These signals are used for
// BL8 to ignore and insert data for even len transactions with offset
// and odd len transactions
// For odd len transactions with no offset the last read is ignored and
// last write is masked
// For odd len transactions with offset the first read is ignored and
// first write is masked
// For even len transactions with offset the last & first read is ignored and
// last& first write is masked
// For even len transactions no ingnores or masks.
// Indicates if we are on the first transaction of a mc translation with more
// than 1 transaction.
always @(posedge clk) begin
if (reset | axhandshake) begin
sel_first <= 1'b1;
end else if (next) begin
sel_first <= 1'b0;
end
end
endmodule
`default_nettype wire
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_incr_cmd.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_incr_cmd #
(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
// Width of AxADDR
// Range: 32.
parameter integer C_AXI_ADDR_WIDTH = 32
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
input wire [C_AXI_ADDR_WIDTH-1:0] axaddr ,
input wire [7:0] axlen ,
input wire [2:0] axsize ,
// axhandshake = axvalid & axready
input wire axhandshake ,
output wire [C_AXI_ADDR_WIDTH-1:0] cmd_byte_addr ,
// Connections to/from fsm module
// signal to increment to the next mc transaction
input wire next ,
// signal to the fsm there is another transaction required
output reg next_pending
);
////////////////////////////////////////////////////////////////////////////////
// Wire and register declarations
////////////////////////////////////////////////////////////////////////////////
reg sel_first;
reg [11:0] axaddr_incr;
reg [8:0] axlen_cnt;
reg next_pending_r;
wire [3:0] axsize_shift;
wire [11:0] axsize_mask;
localparam L_AXI_ADDR_LOW_BIT = (C_AXI_ADDR_WIDTH >= 12) ? 12 : 11;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// calculate cmd_byte_addr
generate
if (C_AXI_ADDR_WIDTH > 12) begin : ADDR_GT_4K
assign cmd_byte_addr = (sel_first) ? axaddr : {axaddr[C_AXI_ADDR_WIDTH-1:L_AXI_ADDR_LOW_BIT],axaddr_incr[11:0]};
end else begin : ADDR_4K
assign cmd_byte_addr = (sel_first) ? axaddr : axaddr_incr[11:0];
end
endgenerate
assign axsize_shift = (1 << axsize[1:0]);
assign axsize_mask = ~(axsize_shift - 1'b1);
// Incremented version of axaddr
always @(posedge clk) begin
if (sel_first) begin
if(~next) begin
axaddr_incr <= axaddr[11:0] & axsize_mask;
end else begin
axaddr_incr <= (axaddr[11:0] & axsize_mask) + axsize_shift;
end
end else if (next) begin
axaddr_incr <= axaddr_incr + axsize_shift;
end
end
always @(posedge clk) begin
if (axhandshake)begin
axlen_cnt <= axlen;
next_pending_r <= (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
axlen_cnt <= axlen_cnt - 1;
next_pending_r <= ((axlen_cnt - 1) >= 1);
end else begin
axlen_cnt <= 9'd0;
next_pending_r <= 1'b0;
end
end
end
always @( * ) begin
if (axhandshake)begin
next_pending = (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
next_pending = ((axlen_cnt - 1) >= 1);
end else begin
next_pending = 1'b0;
end
end else begin
next_pending = next_pending_r;
end
end
// last and ignore signals to data channel. These signals are used for
// BL8 to ignore and insert data for even len transactions with offset
// and odd len transactions
// For odd len transactions with no offset the last read is ignored and
// last write is masked
// For odd len transactions with offset the first read is ignored and
// first write is masked
// For even len transactions with offset the last & first read is ignored and
// last& first write is masked
// For even len transactions no ingnores or masks.
// Indicates if we are on the first transaction of a mc translation with more
// than 1 transaction.
always @(posedge clk) begin
if (reset | axhandshake) begin
sel_first <= 1'b1;
end else if (next) begin
sel_first <= 1'b0;
end
end
endmodule
`default_nettype wire
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_incr_cmd.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_incr_cmd #
(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
// Width of AxADDR
// Range: 32.
parameter integer C_AXI_ADDR_WIDTH = 32
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
input wire [C_AXI_ADDR_WIDTH-1:0] axaddr ,
input wire [7:0] axlen ,
input wire [2:0] axsize ,
// axhandshake = axvalid & axready
input wire axhandshake ,
output wire [C_AXI_ADDR_WIDTH-1:0] cmd_byte_addr ,
// Connections to/from fsm module
// signal to increment to the next mc transaction
input wire next ,
// signal to the fsm there is another transaction required
output reg next_pending
);
////////////////////////////////////////////////////////////////////////////////
// Wire and register declarations
////////////////////////////////////////////////////////////////////////////////
reg sel_first;
reg [11:0] axaddr_incr;
reg [8:0] axlen_cnt;
reg next_pending_r;
wire [3:0] axsize_shift;
wire [11:0] axsize_mask;
localparam L_AXI_ADDR_LOW_BIT = (C_AXI_ADDR_WIDTH >= 12) ? 12 : 11;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// calculate cmd_byte_addr
generate
if (C_AXI_ADDR_WIDTH > 12) begin : ADDR_GT_4K
assign cmd_byte_addr = (sel_first) ? axaddr : {axaddr[C_AXI_ADDR_WIDTH-1:L_AXI_ADDR_LOW_BIT],axaddr_incr[11:0]};
end else begin : ADDR_4K
assign cmd_byte_addr = (sel_first) ? axaddr : axaddr_incr[11:0];
end
endgenerate
assign axsize_shift = (1 << axsize[1:0]);
assign axsize_mask = ~(axsize_shift - 1'b1);
// Incremented version of axaddr
always @(posedge clk) begin
if (sel_first) begin
if(~next) begin
axaddr_incr <= axaddr[11:0] & axsize_mask;
end else begin
axaddr_incr <= (axaddr[11:0] & axsize_mask) + axsize_shift;
end
end else if (next) begin
axaddr_incr <= axaddr_incr + axsize_shift;
end
end
always @(posedge clk) begin
if (axhandshake)begin
axlen_cnt <= axlen;
next_pending_r <= (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
axlen_cnt <= axlen_cnt - 1;
next_pending_r <= ((axlen_cnt - 1) >= 1);
end else begin
axlen_cnt <= 9'd0;
next_pending_r <= 1'b0;
end
end
end
always @( * ) begin
if (axhandshake)begin
next_pending = (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
next_pending = ((axlen_cnt - 1) >= 1);
end else begin
next_pending = 1'b0;
end
end else begin
next_pending = next_pending_r;
end
end
// last and ignore signals to data channel. These signals are used for
// BL8 to ignore and insert data for even len transactions with offset
// and odd len transactions
// For odd len transactions with no offset the last read is ignored and
// last write is masked
// For odd len transactions with offset the first read is ignored and
// first write is masked
// For even len transactions with offset the last & first read is ignored and
// last& first write is masked
// For even len transactions no ingnores or masks.
// Indicates if we are on the first transaction of a mc translation with more
// than 1 transaction.
always @(posedge clk) begin
if (reset | axhandshake) begin
sel_first <= 1'b1;
end else if (next) begin
sel_first <= 1'b0;
end
end
endmodule
`default_nettype wire
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_incr_cmd.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_incr_cmd #
(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
// Width of AxADDR
// Range: 32.
parameter integer C_AXI_ADDR_WIDTH = 32
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
input wire [C_AXI_ADDR_WIDTH-1:0] axaddr ,
input wire [7:0] axlen ,
input wire [2:0] axsize ,
// axhandshake = axvalid & axready
input wire axhandshake ,
output wire [C_AXI_ADDR_WIDTH-1:0] cmd_byte_addr ,
// Connections to/from fsm module
// signal to increment to the next mc transaction
input wire next ,
// signal to the fsm there is another transaction required
output reg next_pending
);
////////////////////////////////////////////////////////////////////////////////
// Wire and register declarations
////////////////////////////////////////////////////////////////////////////////
reg sel_first;
reg [11:0] axaddr_incr;
reg [8:0] axlen_cnt;
reg next_pending_r;
wire [3:0] axsize_shift;
wire [11:0] axsize_mask;
localparam L_AXI_ADDR_LOW_BIT = (C_AXI_ADDR_WIDTH >= 12) ? 12 : 11;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// calculate cmd_byte_addr
generate
if (C_AXI_ADDR_WIDTH > 12) begin : ADDR_GT_4K
assign cmd_byte_addr = (sel_first) ? axaddr : {axaddr[C_AXI_ADDR_WIDTH-1:L_AXI_ADDR_LOW_BIT],axaddr_incr[11:0]};
end else begin : ADDR_4K
assign cmd_byte_addr = (sel_first) ? axaddr : axaddr_incr[11:0];
end
endgenerate
assign axsize_shift = (1 << axsize[1:0]);
assign axsize_mask = ~(axsize_shift - 1'b1);
// Incremented version of axaddr
always @(posedge clk) begin
if (sel_first) begin
if(~next) begin
axaddr_incr <= axaddr[11:0] & axsize_mask;
end else begin
axaddr_incr <= (axaddr[11:0] & axsize_mask) + axsize_shift;
end
end else if (next) begin
axaddr_incr <= axaddr_incr + axsize_shift;
end
end
always @(posedge clk) begin
if (axhandshake)begin
axlen_cnt <= axlen;
next_pending_r <= (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
axlen_cnt <= axlen_cnt - 1;
next_pending_r <= ((axlen_cnt - 1) >= 1);
end else begin
axlen_cnt <= 9'd0;
next_pending_r <= 1'b0;
end
end
end
always @( * ) begin
if (axhandshake)begin
next_pending = (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
next_pending = ((axlen_cnt - 1) >= 1);
end else begin
next_pending = 1'b0;
end
end else begin
next_pending = next_pending_r;
end
end
// last and ignore signals to data channel. These signals are used for
// BL8 to ignore and insert data for even len transactions with offset
// and odd len transactions
// For odd len transactions with no offset the last read is ignored and
// last write is masked
// For odd len transactions with offset the first read is ignored and
// first write is masked
// For even len transactions with offset the last & first read is ignored and
// last& first write is masked
// For even len transactions no ingnores or masks.
// Indicates if we are on the first transaction of a mc translation with more
// than 1 transaction.
always @(posedge clk) begin
if (reset | axhandshake) begin
sel_first <= 1'b1;
end else if (next) begin
sel_first <= 1'b0;
end
end
endmodule
`default_nettype wire
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s_incr_cmd.v
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_incr_cmd #
(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
// Width of AxADDR
// Range: 32.
parameter integer C_AXI_ADDR_WIDTH = 32
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire clk ,
input wire reset ,
input wire [C_AXI_ADDR_WIDTH-1:0] axaddr ,
input wire [7:0] axlen ,
input wire [2:0] axsize ,
// axhandshake = axvalid & axready
input wire axhandshake ,
output wire [C_AXI_ADDR_WIDTH-1:0] cmd_byte_addr ,
// Connections to/from fsm module
// signal to increment to the next mc transaction
input wire next ,
// signal to the fsm there is another transaction required
output reg next_pending
);
////////////////////////////////////////////////////////////////////////////////
// Wire and register declarations
////////////////////////////////////////////////////////////////////////////////
reg sel_first;
reg [11:0] axaddr_incr;
reg [8:0] axlen_cnt;
reg next_pending_r;
wire [3:0] axsize_shift;
wire [11:0] axsize_mask;
localparam L_AXI_ADDR_LOW_BIT = (C_AXI_ADDR_WIDTH >= 12) ? 12 : 11;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// calculate cmd_byte_addr
generate
if (C_AXI_ADDR_WIDTH > 12) begin : ADDR_GT_4K
assign cmd_byte_addr = (sel_first) ? axaddr : {axaddr[C_AXI_ADDR_WIDTH-1:L_AXI_ADDR_LOW_BIT],axaddr_incr[11:0]};
end else begin : ADDR_4K
assign cmd_byte_addr = (sel_first) ? axaddr : axaddr_incr[11:0];
end
endgenerate
assign axsize_shift = (1 << axsize[1:0]);
assign axsize_mask = ~(axsize_shift - 1'b1);
// Incremented version of axaddr
always @(posedge clk) begin
if (sel_first) begin
if(~next) begin
axaddr_incr <= axaddr[11:0] & axsize_mask;
end else begin
axaddr_incr <= (axaddr[11:0] & axsize_mask) + axsize_shift;
end
end else if (next) begin
axaddr_incr <= axaddr_incr + axsize_shift;
end
end
always @(posedge clk) begin
if (axhandshake)begin
axlen_cnt <= axlen;
next_pending_r <= (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
axlen_cnt <= axlen_cnt - 1;
next_pending_r <= ((axlen_cnt - 1) >= 1);
end else begin
axlen_cnt <= 9'd0;
next_pending_r <= 1'b0;
end
end
end
always @( * ) begin
if (axhandshake)begin
next_pending = (axlen >= 1);
end else if (next) begin
if (axlen_cnt > 1) begin
next_pending = ((axlen_cnt - 1) >= 1);
end else begin
next_pending = 1'b0;
end
end else begin
next_pending = next_pending_r;
end
end
// last and ignore signals to data channel. These signals are used for
// BL8 to ignore and insert data for even len transactions with offset
// and odd len transactions
// For odd len transactions with no offset the last read is ignored and
// last write is masked
// For odd len transactions with offset the first read is ignored and
// first write is masked
// For even len transactions with offset the last & first read is ignored and
// last& first write is masked
// For even len transactions no ingnores or masks.
// Indicates if we are on the first transaction of a mc translation with more
// than 1 transaction.
always @(posedge clk) begin
if (reset | axhandshake) begin
sel_first <= 1'b1;
end else if (next) begin
sel_first <= 1'b0;
end
end
endmodule
`default_nettype wire
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: BLK_MEM_GEN_v8_2.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_2 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_2 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_2 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_2 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_2 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_2
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_2 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_2 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_2 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_2 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_2
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_2 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_2
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_2
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_2
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (BLK_MEM_GEN_v8_2) which is
// declared/implemented further down in this file.
//*****************************************************************************
module BLK_MEM_GEN_v8_2_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module BLK_MEM_GEN_v8_2_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_2" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_2_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_2
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = ""
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_2
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: BLK_MEM_GEN_v8_2.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_2 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_2 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_2 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_2 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_2 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_2
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_2 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_2 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_2 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_2 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_2
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_2 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_2
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_2
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_2
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (BLK_MEM_GEN_v8_2) which is
// declared/implemented further down in this file.
//*****************************************************************************
module BLK_MEM_GEN_v8_2_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module BLK_MEM_GEN_v8_2_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_2" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_2_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_2
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = ""
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_2
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: BLK_MEM_GEN_v8_2.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_2 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_2 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_2 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_2 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_2 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_2
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_2 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_2 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_2 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_2 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_2
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_2 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_2
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_2
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_2
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (BLK_MEM_GEN_v8_2) which is
// declared/implemented further down in this file.
//*****************************************************************************
module BLK_MEM_GEN_v8_2_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module BLK_MEM_GEN_v8_2_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_2" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_2_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_2
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = ""
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_2
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: BLK_MEM_GEN_v8_2.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_2 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_2 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_2 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_2 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_2 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_2
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_2 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_2 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_2 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_2 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_2 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_2 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_2 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_2 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_2 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_2
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_2 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_2
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_2
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_2
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (BLK_MEM_GEN_v8_2) which is
// declared/implemented further down in this file.
//*****************************************************************************
module BLK_MEM_GEN_v8_2_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module BLK_MEM_GEN_v8_2_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_2" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_2_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
BLK_MEM_GEN_v8_2_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
BLK_MEM_GEN_v8_2_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_2
#(parameter C_CORENAME = "blk_mem_gen_v8_2",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = ""
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (CLKA),
.RSTA (rsta_in),
.ENA (ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB),
.ENB (ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_2
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_2
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
BLK_MEM_GEN_v8_2_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_2_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
// -*- verilog -*-
//
// USRP - Universal Software Radio Peripheral
//
// Copyright (C) 2003 Matt Ettus
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 51 Franklin Street, Boston, MA 02110-1301 USA
//
// Sign extension "macro"
// bits_out should be greater than bits_in
module sign_extend (in,out);
parameter bits_in=0; // FIXME Quartus insists on a default
parameter bits_out=0;
input [bits_in-1:0] in;
output [bits_out-1:0] out;
assign out = {{(bits_out-bits_in){in[bits_in-1]}},in};
endmodule
|
//Legal Notice: (C)2017 Altera Corporation. All rights reserved. Your
//use of Altera Corporation's design tools, logic functions and other
//software and tools, and its AMPP partner logic functions, and any
//output files any of the foregoing (including device programming or
//simulation files), and any associated documentation or information are
//expressly subject to the terms and conditions of the Altera Program
//License Subscription Agreement or other applicable license agreement,
//including, without limitation, that your use is for the sole purpose
//of programming logic devices manufactured by Altera and sold by Altera
//or its authorized distributors. Please refer to the applicable
//agreement for further details.
// synthesis translate_off
`timescale 1ns / 1ps
// synthesis translate_on
// turn off superfluous verilog processor warnings
// altera message_level Level1
// altera message_off 10034 10035 10036 10037 10230 10240 10030
module soc_design_Sys_Timer (
// inputs:
address,
chipselect,
clk,
reset_n,
write_n,
writedata,
// outputs:
irq,
readdata
)
;
output irq;
output [ 15: 0] readdata;
input [ 2: 0] address;
input chipselect;
input clk;
input reset_n;
input write_n;
input [ 15: 0] writedata;
wire clk_en;
wire control_interrupt_enable;
reg control_register;
wire control_wr_strobe;
reg counter_is_running;
wire counter_is_zero;
wire [ 16: 0] counter_load_value;
reg delayed_unxcounter_is_zeroxx0;
wire do_start_counter;
wire do_stop_counter;
reg force_reload;
reg [ 16: 0] internal_counter;
wire irq;
wire period_h_wr_strobe;
wire period_l_wr_strobe;
wire [ 15: 0] read_mux_out;
reg [ 15: 0] readdata;
wire status_wr_strobe;
wire timeout_event;
reg timeout_occurred;
assign clk_en = 1;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
internal_counter <= 17'h1869F;
else if (counter_is_running || force_reload)
if (counter_is_zero || force_reload)
internal_counter <= counter_load_value;
else
internal_counter <= internal_counter - 1;
end
assign counter_is_zero = internal_counter == 0;
assign counter_load_value = 17'h1869F;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
force_reload <= 0;
else if (clk_en)
force_reload <= period_h_wr_strobe || period_l_wr_strobe;
end
assign do_start_counter = 1;
assign do_stop_counter = 0;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
counter_is_running <= 1'b0;
else if (clk_en)
if (do_start_counter)
counter_is_running <= -1;
else if (do_stop_counter)
counter_is_running <= 0;
end
//delayed_unxcounter_is_zeroxx0, which is an e_register
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
delayed_unxcounter_is_zeroxx0 <= 0;
else if (clk_en)
delayed_unxcounter_is_zeroxx0 <= counter_is_zero;
end
assign timeout_event = (counter_is_zero) & ~(delayed_unxcounter_is_zeroxx0);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
timeout_occurred <= 0;
else if (clk_en)
if (status_wr_strobe)
timeout_occurred <= 0;
else if (timeout_event)
timeout_occurred <= -1;
end
assign irq = timeout_occurred && control_interrupt_enable;
//s1, which is an e_avalon_slave
assign read_mux_out = ({16 {(address == 1)}} & control_register) |
({16 {(address == 0)}} & {counter_is_running,
timeout_occurred});
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
readdata <= 0;
else if (clk_en)
readdata <= read_mux_out;
end
assign period_l_wr_strobe = chipselect && ~write_n && (address == 2);
assign period_h_wr_strobe = chipselect && ~write_n && (address == 3);
assign control_wr_strobe = chipselect && ~write_n && (address == 1);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
control_register <= 0;
else if (control_wr_strobe)
control_register <= writedata[0];
end
assign control_interrupt_enable = control_register;
assign status_wr_strobe = chipselect && ~write_n && (address == 0);
endmodule
|
//Legal Notice: (C)2017 Altera Corporation. All rights reserved. Your
//use of Altera Corporation's design tools, logic functions and other
//software and tools, and its AMPP partner logic functions, and any
//output files any of the foregoing (including device programming or
//simulation files), and any associated documentation or information are
//expressly subject to the terms and conditions of the Altera Program
//License Subscription Agreement or other applicable license agreement,
//including, without limitation, that your use is for the sole purpose
//of programming logic devices manufactured by Altera and sold by Altera
//or its authorized distributors. Please refer to the applicable
//agreement for further details.
// synthesis translate_off
`timescale 1ns / 1ps
// synthesis translate_on
// turn off superfluous verilog processor warnings
// altera message_level Level1
// altera message_off 10034 10035 10036 10037 10230 10240 10030
module soc_design_Sys_Timer (
// inputs:
address,
chipselect,
clk,
reset_n,
write_n,
writedata,
// outputs:
irq,
readdata
)
;
output irq;
output [ 15: 0] readdata;
input [ 2: 0] address;
input chipselect;
input clk;
input reset_n;
input write_n;
input [ 15: 0] writedata;
wire clk_en;
wire control_interrupt_enable;
reg control_register;
wire control_wr_strobe;
reg counter_is_running;
wire counter_is_zero;
wire [ 16: 0] counter_load_value;
reg delayed_unxcounter_is_zeroxx0;
wire do_start_counter;
wire do_stop_counter;
reg force_reload;
reg [ 16: 0] internal_counter;
wire irq;
wire period_h_wr_strobe;
wire period_l_wr_strobe;
wire [ 15: 0] read_mux_out;
reg [ 15: 0] readdata;
wire status_wr_strobe;
wire timeout_event;
reg timeout_occurred;
assign clk_en = 1;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
internal_counter <= 17'h1869F;
else if (counter_is_running || force_reload)
if (counter_is_zero || force_reload)
internal_counter <= counter_load_value;
else
internal_counter <= internal_counter - 1;
end
assign counter_is_zero = internal_counter == 0;
assign counter_load_value = 17'h1869F;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
force_reload <= 0;
else if (clk_en)
force_reload <= period_h_wr_strobe || period_l_wr_strobe;
end
assign do_start_counter = 1;
assign do_stop_counter = 0;
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
counter_is_running <= 1'b0;
else if (clk_en)
if (do_start_counter)
counter_is_running <= -1;
else if (do_stop_counter)
counter_is_running <= 0;
end
//delayed_unxcounter_is_zeroxx0, which is an e_register
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
delayed_unxcounter_is_zeroxx0 <= 0;
else if (clk_en)
delayed_unxcounter_is_zeroxx0 <= counter_is_zero;
end
assign timeout_event = (counter_is_zero) & ~(delayed_unxcounter_is_zeroxx0);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
timeout_occurred <= 0;
else if (clk_en)
if (status_wr_strobe)
timeout_occurred <= 0;
else if (timeout_event)
timeout_occurred <= -1;
end
assign irq = timeout_occurred && control_interrupt_enable;
//s1, which is an e_avalon_slave
assign read_mux_out = ({16 {(address == 1)}} & control_register) |
({16 {(address == 0)}} & {counter_is_running,
timeout_occurred});
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
readdata <= 0;
else if (clk_en)
readdata <= read_mux_out;
end
assign period_l_wr_strobe = chipselect && ~write_n && (address == 2);
assign period_h_wr_strobe = chipselect && ~write_n && (address == 3);
assign control_wr_strobe = chipselect && ~write_n && (address == 1);
always @(posedge clk or negedge reset_n)
begin
if (reset_n == 0)
control_register <= 0;
else if (control_wr_strobe)
control_register <= writedata[0];
end
assign control_interrupt_enable = control_register;
assign status_wr_strobe = chipselect && ~write_n && (address == 0);
endmodule
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: AxiLite Slave Conversion
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// axilite_conv
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_axilite_conv #
(
parameter C_FAMILY = "virtex6",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1
)
(
// System Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [3-1:0] S_AXI_AWPROT,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER, // Constant =0
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [3-1:0] S_AXI_ARPROT,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST, // Constant =1
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER, // Constant =0
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [3-1:0] M_AXI_AWPROT,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [2-1:0] M_AXI_BRESP,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [3-1:0] M_AXI_ARPROT,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY
);
wire s_awvalid_i;
wire s_arvalid_i;
wire [C_AXI_ADDR_WIDTH-1:0] m_axaddr;
// Arbiter
reg read_active;
reg write_active;
reg busy;
wire read_req;
wire write_req;
wire read_complete;
wire write_complete;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ~ARESETN};
end
assign s_awvalid_i = S_AXI_AWVALID & (C_AXI_SUPPORTS_WRITE != 0);
assign s_arvalid_i = S_AXI_ARVALID & (C_AXI_SUPPORTS_READ != 0);
assign read_req = s_arvalid_i & ~busy & ~|areset_d & ~write_active;
assign write_req = s_awvalid_i & ~busy & ~|areset_d & ((~read_active & ~s_arvalid_i) | write_active);
assign read_complete = M_AXI_RVALID & S_AXI_RREADY;
assign write_complete = M_AXI_BVALID & S_AXI_BREADY;
always @(posedge ACLK) begin : arbiter_read_ff
if (|areset_d)
read_active <= 1'b0;
else if (read_complete)
read_active <= 1'b0;
else if (read_req)
read_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_write_ff
if (|areset_d)
write_active <= 1'b0;
else if (write_complete)
write_active <= 1'b0;
else if (write_req)
write_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_busy_ff
if (|areset_d)
busy <= 1'b0;
else if (read_complete | write_complete)
busy <= 1'b0;
else if ((write_req & M_AXI_AWREADY) | (read_req & M_AXI_ARREADY))
busy <= 1'b1;
end
assign M_AXI_ARVALID = read_req;
assign S_AXI_ARREADY = M_AXI_ARREADY & read_req;
assign M_AXI_AWVALID = write_req;
assign S_AXI_AWREADY = M_AXI_AWREADY & write_req;
assign M_AXI_RREADY = S_AXI_RREADY & read_active;
assign S_AXI_RVALID = M_AXI_RVALID & read_active;
assign M_AXI_BREADY = S_AXI_BREADY & write_active;
assign S_AXI_BVALID = M_AXI_BVALID & write_active;
// Address multiplexer
assign m_axaddr = (read_req | (C_AXI_SUPPORTS_WRITE == 0)) ? S_AXI_ARADDR : S_AXI_AWADDR;
// Id multiplexer and flip-flop
reg [C_AXI_ID_WIDTH-1:0] s_axid;
always @(posedge ACLK) begin : axid
if (read_req) s_axid <= S_AXI_ARID;
else if (write_req) s_axid <= S_AXI_AWID;
end
assign S_AXI_BID = s_axid;
assign S_AXI_RID = s_axid;
assign M_AXI_AWADDR = m_axaddr;
assign M_AXI_ARADDR = m_axaddr;
// Feed-through signals
assign S_AXI_WREADY = M_AXI_WREADY & ~|areset_d;
assign S_AXI_BRESP = M_AXI_BRESP;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = 1'b1;
assign S_AXI_BUSER = {C_AXI_BUSER_WIDTH{1'b0}};
assign S_AXI_RUSER = {C_AXI_RUSER_WIDTH{1'b0}};
assign M_AXI_AWPROT = S_AXI_AWPROT;
assign M_AXI_WVALID = S_AXI_WVALID & ~|areset_d;
assign M_AXI_WDATA = S_AXI_WDATA;
assign M_AXI_WSTRB = S_AXI_WSTRB;
assign M_AXI_ARPROT = S_AXI_ARPROT;
endmodule
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: AxiLite Slave Conversion
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// axilite_conv
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_axilite_conv #
(
parameter C_FAMILY = "virtex6",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1
)
(
// System Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [3-1:0] S_AXI_AWPROT,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER, // Constant =0
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [3-1:0] S_AXI_ARPROT,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST, // Constant =1
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER, // Constant =0
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [3-1:0] M_AXI_AWPROT,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [2-1:0] M_AXI_BRESP,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [3-1:0] M_AXI_ARPROT,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY
);
wire s_awvalid_i;
wire s_arvalid_i;
wire [C_AXI_ADDR_WIDTH-1:0] m_axaddr;
// Arbiter
reg read_active;
reg write_active;
reg busy;
wire read_req;
wire write_req;
wire read_complete;
wire write_complete;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ~ARESETN};
end
assign s_awvalid_i = S_AXI_AWVALID & (C_AXI_SUPPORTS_WRITE != 0);
assign s_arvalid_i = S_AXI_ARVALID & (C_AXI_SUPPORTS_READ != 0);
assign read_req = s_arvalid_i & ~busy & ~|areset_d & ~write_active;
assign write_req = s_awvalid_i & ~busy & ~|areset_d & ((~read_active & ~s_arvalid_i) | write_active);
assign read_complete = M_AXI_RVALID & S_AXI_RREADY;
assign write_complete = M_AXI_BVALID & S_AXI_BREADY;
always @(posedge ACLK) begin : arbiter_read_ff
if (|areset_d)
read_active <= 1'b0;
else if (read_complete)
read_active <= 1'b0;
else if (read_req)
read_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_write_ff
if (|areset_d)
write_active <= 1'b0;
else if (write_complete)
write_active <= 1'b0;
else if (write_req)
write_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_busy_ff
if (|areset_d)
busy <= 1'b0;
else if (read_complete | write_complete)
busy <= 1'b0;
else if ((write_req & M_AXI_AWREADY) | (read_req & M_AXI_ARREADY))
busy <= 1'b1;
end
assign M_AXI_ARVALID = read_req;
assign S_AXI_ARREADY = M_AXI_ARREADY & read_req;
assign M_AXI_AWVALID = write_req;
assign S_AXI_AWREADY = M_AXI_AWREADY & write_req;
assign M_AXI_RREADY = S_AXI_RREADY & read_active;
assign S_AXI_RVALID = M_AXI_RVALID & read_active;
assign M_AXI_BREADY = S_AXI_BREADY & write_active;
assign S_AXI_BVALID = M_AXI_BVALID & write_active;
// Address multiplexer
assign m_axaddr = (read_req | (C_AXI_SUPPORTS_WRITE == 0)) ? S_AXI_ARADDR : S_AXI_AWADDR;
// Id multiplexer and flip-flop
reg [C_AXI_ID_WIDTH-1:0] s_axid;
always @(posedge ACLK) begin : axid
if (read_req) s_axid <= S_AXI_ARID;
else if (write_req) s_axid <= S_AXI_AWID;
end
assign S_AXI_BID = s_axid;
assign S_AXI_RID = s_axid;
assign M_AXI_AWADDR = m_axaddr;
assign M_AXI_ARADDR = m_axaddr;
// Feed-through signals
assign S_AXI_WREADY = M_AXI_WREADY & ~|areset_d;
assign S_AXI_BRESP = M_AXI_BRESP;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = 1'b1;
assign S_AXI_BUSER = {C_AXI_BUSER_WIDTH{1'b0}};
assign S_AXI_RUSER = {C_AXI_RUSER_WIDTH{1'b0}};
assign M_AXI_AWPROT = S_AXI_AWPROT;
assign M_AXI_WVALID = S_AXI_WVALID & ~|areset_d;
assign M_AXI_WDATA = S_AXI_WDATA;
assign M_AXI_WSTRB = S_AXI_WSTRB;
assign M_AXI_ARPROT = S_AXI_ARPROT;
endmodule
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Description: AxiLite Slave Conversion
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// axilite_conv
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_axilite_conv #
(
parameter C_FAMILY = "virtex6",
parameter integer C_AXI_ID_WIDTH = 1,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1
)
(
// System Signals
input wire ACLK,
input wire ARESETN,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_AWADDR,
input wire [3-1:0] S_AXI_AWPROT,
input wire S_AXI_AWVALID,
output wire S_AXI_AWREADY,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] S_AXI_WDATA,
input wire [C_AXI_DATA_WIDTH/8-1:0] S_AXI_WSTRB,
input wire S_AXI_WVALID,
output wire S_AXI_WREADY,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID,
output wire [2-1:0] S_AXI_BRESP,
output wire [C_AXI_BUSER_WIDTH-1:0] S_AXI_BUSER, // Constant =0
output wire S_AXI_BVALID,
input wire S_AXI_BREADY,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
input wire [C_AXI_ADDR_WIDTH-1:0] S_AXI_ARADDR,
input wire [3-1:0] S_AXI_ARPROT,
input wire S_AXI_ARVALID,
output wire S_AXI_ARREADY,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID,
output wire [C_AXI_DATA_WIDTH-1:0] S_AXI_RDATA,
output wire [2-1:0] S_AXI_RRESP,
output wire S_AXI_RLAST, // Constant =1
output wire [C_AXI_RUSER_WIDTH-1:0] S_AXI_RUSER, // Constant =0
output wire S_AXI_RVALID,
input wire S_AXI_RREADY,
// Master Interface Write Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_AWADDR,
output wire [3-1:0] M_AXI_AWPROT,
output wire M_AXI_AWVALID,
input wire M_AXI_AWREADY,
// Master Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] M_AXI_WDATA,
output wire [C_AXI_DATA_WIDTH/8-1:0] M_AXI_WSTRB,
output wire M_AXI_WVALID,
input wire M_AXI_WREADY,
// Master Interface Write Response Ports
input wire [2-1:0] M_AXI_BRESP,
input wire M_AXI_BVALID,
output wire M_AXI_BREADY,
// Master Interface Read Address Port
output wire [C_AXI_ADDR_WIDTH-1:0] M_AXI_ARADDR,
output wire [3-1:0] M_AXI_ARPROT,
output wire M_AXI_ARVALID,
input wire M_AXI_ARREADY,
// Master Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] M_AXI_RDATA,
input wire [2-1:0] M_AXI_RRESP,
input wire M_AXI_RVALID,
output wire M_AXI_RREADY
);
wire s_awvalid_i;
wire s_arvalid_i;
wire [C_AXI_ADDR_WIDTH-1:0] m_axaddr;
// Arbiter
reg read_active;
reg write_active;
reg busy;
wire read_req;
wire write_req;
wire read_complete;
wire write_complete;
reg [1:0] areset_d; // Reset delay register
always @(posedge ACLK) begin
areset_d <= {areset_d[0], ~ARESETN};
end
assign s_awvalid_i = S_AXI_AWVALID & (C_AXI_SUPPORTS_WRITE != 0);
assign s_arvalid_i = S_AXI_ARVALID & (C_AXI_SUPPORTS_READ != 0);
assign read_req = s_arvalid_i & ~busy & ~|areset_d & ~write_active;
assign write_req = s_awvalid_i & ~busy & ~|areset_d & ((~read_active & ~s_arvalid_i) | write_active);
assign read_complete = M_AXI_RVALID & S_AXI_RREADY;
assign write_complete = M_AXI_BVALID & S_AXI_BREADY;
always @(posedge ACLK) begin : arbiter_read_ff
if (|areset_d)
read_active <= 1'b0;
else if (read_complete)
read_active <= 1'b0;
else if (read_req)
read_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_write_ff
if (|areset_d)
write_active <= 1'b0;
else if (write_complete)
write_active <= 1'b0;
else if (write_req)
write_active <= 1'b1;
end
always @(posedge ACLK) begin : arbiter_busy_ff
if (|areset_d)
busy <= 1'b0;
else if (read_complete | write_complete)
busy <= 1'b0;
else if ((write_req & M_AXI_AWREADY) | (read_req & M_AXI_ARREADY))
busy <= 1'b1;
end
assign M_AXI_ARVALID = read_req;
assign S_AXI_ARREADY = M_AXI_ARREADY & read_req;
assign M_AXI_AWVALID = write_req;
assign S_AXI_AWREADY = M_AXI_AWREADY & write_req;
assign M_AXI_RREADY = S_AXI_RREADY & read_active;
assign S_AXI_RVALID = M_AXI_RVALID & read_active;
assign M_AXI_BREADY = S_AXI_BREADY & write_active;
assign S_AXI_BVALID = M_AXI_BVALID & write_active;
// Address multiplexer
assign m_axaddr = (read_req | (C_AXI_SUPPORTS_WRITE == 0)) ? S_AXI_ARADDR : S_AXI_AWADDR;
// Id multiplexer and flip-flop
reg [C_AXI_ID_WIDTH-1:0] s_axid;
always @(posedge ACLK) begin : axid
if (read_req) s_axid <= S_AXI_ARID;
else if (write_req) s_axid <= S_AXI_AWID;
end
assign S_AXI_BID = s_axid;
assign S_AXI_RID = s_axid;
assign M_AXI_AWADDR = m_axaddr;
assign M_AXI_ARADDR = m_axaddr;
// Feed-through signals
assign S_AXI_WREADY = M_AXI_WREADY & ~|areset_d;
assign S_AXI_BRESP = M_AXI_BRESP;
assign S_AXI_RDATA = M_AXI_RDATA;
assign S_AXI_RRESP = M_AXI_RRESP;
assign S_AXI_RLAST = 1'b1;
assign S_AXI_BUSER = {C_AXI_BUSER_WIDTH{1'b0}};
assign S_AXI_RUSER = {C_AXI_RUSER_WIDTH{1'b0}};
assign M_AXI_AWPROT = S_AXI_AWPROT;
assign M_AXI_WVALID = S_AXI_WVALID & ~|areset_d;
assign M_AXI_WDATA = S_AXI_WDATA;
assign M_AXI_WSTRB = S_AXI_WSTRB;
assign M_AXI_ARPROT = S_AXI_ARPROT;
endmodule
|
// This is a component of pluto_step, a hardware step waveform generator
// Copyright 2007 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule
|
// This is a component of pluto_step, a hardware step waveform generator
// Copyright 2007 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule
|
// This is a component of pluto_step, a hardware step waveform generator
// Copyright 2007 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule
|
// This is a component of pluto_step, a hardware step waveform generator
// Copyright 2007 Jeff Epler <[email protected]>
//
// This program is free software; you can redistribute it and/or modify
// it under the terms of the GNU General Public License as published by
// the Free Software Foundation; either version 2 of the License, or
// (at your option) any later version.
//
// This program is distributed in the hope that it will be useful,
// but WITHOUT ANY WARRANTY; without even the implied warranty of
// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
// GNU General Public License for more details.
//
// You should have received a copy of the GNU General Public License
// along with this program; if not, write to the Free Software
// Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
module stepgen(clk, enable, position, velocity, dirtime, steptime, step, dir, tap);
`define STATE_STEP 0
`define STATE_DIRCHANGE 1
`define STATE_DIRWAIT 2
parameter W=12;
parameter F=10;
parameter T=5;
input clk, enable;
output [W+F-1:0] position; reg [W+F-1:0] position;
input [F:0] velocity;
input [T-1:0] dirtime, steptime;
input [1:0] tap;
output step, dir;
reg step, dir;
reg [T-1:0] timer;
reg [1:0] state;
reg ones;
wire dbit = velocity[F];
wire pbit = (tap == 0 ? position[F]
: (tap == 1 ? position[F+1]
: (tap == 2 ? position[F+2]
: position[F+3])));
wire [W+F-1:0] xvelocity = {{W{velocity[F]}}, {1{velocity[F-1:0]}}};
`ifdef TESTING
// for testing:
initial position = 1'b0;
initial state = `STATE_STEP;
initial timer = 0;
initial dir = 0;
initial ones = 0;
`endif
always @(posedge clk) begin
if(enable) begin
// $display("state=%d timer=%d position=%h velocity=%h dir=%d dbit=%d pbit=%d ones=%d", state, timer, position, xvelocity, dir, dbit, pbit, ones);
if((dir != dbit) && (pbit == ones)) begin
if(state == `STATE_DIRCHANGE) begin
if(timer == 0) begin
dir <= dbit;
timer <= dirtime;
state <= `STATE_DIRWAIT;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
step <= 0;
timer <= dirtime;
state <= `STATE_DIRCHANGE;
end else begin
timer <= timer - 1'd1;
end
end
end else if(state == `STATE_DIRWAIT) begin
if(timer == 0) begin
state <= `STATE_STEP;
end else begin
timer <= timer - 1'd1;
end
end else begin
if(timer == 0) begin
if(pbit != ones) begin
ones <= pbit;
step <= 1'd1;
timer <= steptime;
end else begin
step <= 0;
end
end else begin
timer <= timer - 1'd1;
end
if(dir == dbit)
position <= position + xvelocity;
end
end
end
endmodule
|
//Legal Notice: (C)2017 Altera Corporation. All rights reserved. Your
//use of Altera Corporation's design tools, logic functions and other
//software and tools, and its AMPP partner logic functions, and any
//output files any of the foregoing (including device programming or
//simulation files), and any associated documentation or information are
//expressly subject to the terms and conditions of the Altera Program
//License Subscription Agreement or other applicable license agreement,
//including, without limitation, that your use is for the sole purpose
//of programming logic devices manufactured by Altera and sold by Altera
//or its authorized distributors. Please refer to the applicable
//agreement for further details.
// synthesis translate_off
`timescale 1ns / 1ps
// synthesis translate_on
// turn off superfluous verilog processor warnings
// altera message_level Level1
// altera message_off 10034 10035 10036 10037 10230 10240 10030
module soc_design_niosII_core_cpu_mult_cell (
// inputs:
E_src1,
E_src2,
M_en,
clk,
reset_n,
// outputs:
M_mul_cell_p1,
M_mul_cell_p2,
M_mul_cell_p3
)
;
output [ 31: 0] M_mul_cell_p1;
output [ 31: 0] M_mul_cell_p2;
output [ 31: 0] M_mul_cell_p3;
input [ 31: 0] E_src1;
input [ 31: 0] E_src2;
input M_en;
input clk;
input reset_n;
wire [ 31: 0] M_mul_cell_p1;
wire [ 31: 0] M_mul_cell_p2;
wire [ 31: 0] M_mul_cell_p3;
wire mul_clr;
wire [ 31: 0] mul_src1;
wire [ 31: 0] mul_src2;
assign mul_clr = ~reset_n;
assign mul_src1 = E_src1;
assign mul_src2 = E_src2;
altera_mult_add the_altmult_add_p1
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p1)
);
defparam the_altmult_add_p1.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p1.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p1.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p1.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p1.input_register_a0 = "UNREGISTERED",
the_altmult_add_p1.input_register_b0 = "UNREGISTERED",
the_altmult_add_p1.input_source_a0 = "DATAA",
the_altmult_add_p1.input_source_b0 = "DATAB",
the_altmult_add_p1.lpm_type = "altera_mult_add",
the_altmult_add_p1.multiplier1_direction = "ADD",
the_altmult_add_p1.multiplier_aclr0 = "ACLR0",
the_altmult_add_p1.multiplier_register0 = "CLOCK0",
the_altmult_add_p1.number_of_multipliers = 1,
the_altmult_add_p1.output_register = "UNREGISTERED",
the_altmult_add_p1.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p1.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p1.representation_a = "UNSIGNED",
the_altmult_add_p1.representation_b = "UNSIGNED",
the_altmult_add_p1.selected_device_family = "CYCLONEV",
the_altmult_add_p1.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p1.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p1.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p1.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p1.signed_register_a = "UNREGISTERED",
the_altmult_add_p1.signed_register_b = "UNREGISTERED",
the_altmult_add_p1.width_a = 16,
the_altmult_add_p1.width_b = 16,
the_altmult_add_p1.width_result = 32;
altera_mult_add the_altmult_add_p2
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[31 : 16]),
.ena0 (M_en),
.result (M_mul_cell_p2)
);
defparam the_altmult_add_p2.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p2.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p2.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p2.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p2.input_register_a0 = "UNREGISTERED",
the_altmult_add_p2.input_register_b0 = "UNREGISTERED",
the_altmult_add_p2.input_source_a0 = "DATAA",
the_altmult_add_p2.input_source_b0 = "DATAB",
the_altmult_add_p2.lpm_type = "altera_mult_add",
the_altmult_add_p2.multiplier1_direction = "ADD",
the_altmult_add_p2.multiplier_aclr0 = "ACLR0",
the_altmult_add_p2.multiplier_register0 = "CLOCK0",
the_altmult_add_p2.number_of_multipliers = 1,
the_altmult_add_p2.output_register = "UNREGISTERED",
the_altmult_add_p2.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p2.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p2.representation_a = "UNSIGNED",
the_altmult_add_p2.representation_b = "UNSIGNED",
the_altmult_add_p2.selected_device_family = "CYCLONEV",
the_altmult_add_p2.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p2.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p2.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p2.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p2.signed_register_a = "UNREGISTERED",
the_altmult_add_p2.signed_register_b = "UNREGISTERED",
the_altmult_add_p2.width_a = 16,
the_altmult_add_p2.width_b = 16,
the_altmult_add_p2.width_result = 32;
altera_mult_add the_altmult_add_p3
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[31 : 16]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p3)
);
defparam the_altmult_add_p3.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p3.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p3.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p3.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p3.input_register_a0 = "UNREGISTERED",
the_altmult_add_p3.input_register_b0 = "UNREGISTERED",
the_altmult_add_p3.input_source_a0 = "DATAA",
the_altmult_add_p3.input_source_b0 = "DATAB",
the_altmult_add_p3.lpm_type = "altera_mult_add",
the_altmult_add_p3.multiplier1_direction = "ADD",
the_altmult_add_p3.multiplier_aclr0 = "ACLR0",
the_altmult_add_p3.multiplier_register0 = "CLOCK0",
the_altmult_add_p3.number_of_multipliers = 1,
the_altmult_add_p3.output_register = "UNREGISTERED",
the_altmult_add_p3.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p3.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p3.representation_a = "UNSIGNED",
the_altmult_add_p3.representation_b = "UNSIGNED",
the_altmult_add_p3.selected_device_family = "CYCLONEV",
the_altmult_add_p3.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p3.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p3.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p3.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p3.signed_register_a = "UNREGISTERED",
the_altmult_add_p3.signed_register_b = "UNREGISTERED",
the_altmult_add_p3.width_a = 16,
the_altmult_add_p3.width_b = 16,
the_altmult_add_p3.width_result = 32;
endmodule
|
//Legal Notice: (C)2017 Altera Corporation. All rights reserved. Your
//use of Altera Corporation's design tools, logic functions and other
//software and tools, and its AMPP partner logic functions, and any
//output files any of the foregoing (including device programming or
//simulation files), and any associated documentation or information are
//expressly subject to the terms and conditions of the Altera Program
//License Subscription Agreement or other applicable license agreement,
//including, without limitation, that your use is for the sole purpose
//of programming logic devices manufactured by Altera and sold by Altera
//or its authorized distributors. Please refer to the applicable
//agreement for further details.
// synthesis translate_off
`timescale 1ns / 1ps
// synthesis translate_on
// turn off superfluous verilog processor warnings
// altera message_level Level1
// altera message_off 10034 10035 10036 10037 10230 10240 10030
module soc_design_niosII_core_cpu_mult_cell (
// inputs:
E_src1,
E_src2,
M_en,
clk,
reset_n,
// outputs:
M_mul_cell_p1,
M_mul_cell_p2,
M_mul_cell_p3
)
;
output [ 31: 0] M_mul_cell_p1;
output [ 31: 0] M_mul_cell_p2;
output [ 31: 0] M_mul_cell_p3;
input [ 31: 0] E_src1;
input [ 31: 0] E_src2;
input M_en;
input clk;
input reset_n;
wire [ 31: 0] M_mul_cell_p1;
wire [ 31: 0] M_mul_cell_p2;
wire [ 31: 0] M_mul_cell_p3;
wire mul_clr;
wire [ 31: 0] mul_src1;
wire [ 31: 0] mul_src2;
assign mul_clr = ~reset_n;
assign mul_src1 = E_src1;
assign mul_src2 = E_src2;
altera_mult_add the_altmult_add_p1
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p1)
);
defparam the_altmult_add_p1.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p1.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p1.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p1.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p1.input_register_a0 = "UNREGISTERED",
the_altmult_add_p1.input_register_b0 = "UNREGISTERED",
the_altmult_add_p1.input_source_a0 = "DATAA",
the_altmult_add_p1.input_source_b0 = "DATAB",
the_altmult_add_p1.lpm_type = "altera_mult_add",
the_altmult_add_p1.multiplier1_direction = "ADD",
the_altmult_add_p1.multiplier_aclr0 = "ACLR0",
the_altmult_add_p1.multiplier_register0 = "CLOCK0",
the_altmult_add_p1.number_of_multipliers = 1,
the_altmult_add_p1.output_register = "UNREGISTERED",
the_altmult_add_p1.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p1.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p1.representation_a = "UNSIGNED",
the_altmult_add_p1.representation_b = "UNSIGNED",
the_altmult_add_p1.selected_device_family = "CYCLONEV",
the_altmult_add_p1.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p1.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p1.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p1.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p1.signed_register_a = "UNREGISTERED",
the_altmult_add_p1.signed_register_b = "UNREGISTERED",
the_altmult_add_p1.width_a = 16,
the_altmult_add_p1.width_b = 16,
the_altmult_add_p1.width_result = 32;
altera_mult_add the_altmult_add_p2
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[31 : 16]),
.ena0 (M_en),
.result (M_mul_cell_p2)
);
defparam the_altmult_add_p2.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p2.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p2.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p2.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p2.input_register_a0 = "UNREGISTERED",
the_altmult_add_p2.input_register_b0 = "UNREGISTERED",
the_altmult_add_p2.input_source_a0 = "DATAA",
the_altmult_add_p2.input_source_b0 = "DATAB",
the_altmult_add_p2.lpm_type = "altera_mult_add",
the_altmult_add_p2.multiplier1_direction = "ADD",
the_altmult_add_p2.multiplier_aclr0 = "ACLR0",
the_altmult_add_p2.multiplier_register0 = "CLOCK0",
the_altmult_add_p2.number_of_multipliers = 1,
the_altmult_add_p2.output_register = "UNREGISTERED",
the_altmult_add_p2.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p2.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p2.representation_a = "UNSIGNED",
the_altmult_add_p2.representation_b = "UNSIGNED",
the_altmult_add_p2.selected_device_family = "CYCLONEV",
the_altmult_add_p2.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p2.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p2.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p2.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p2.signed_register_a = "UNREGISTERED",
the_altmult_add_p2.signed_register_b = "UNREGISTERED",
the_altmult_add_p2.width_a = 16,
the_altmult_add_p2.width_b = 16,
the_altmult_add_p2.width_result = 32;
altera_mult_add the_altmult_add_p3
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[31 : 16]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p3)
);
defparam the_altmult_add_p3.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p3.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p3.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p3.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p3.input_register_a0 = "UNREGISTERED",
the_altmult_add_p3.input_register_b0 = "UNREGISTERED",
the_altmult_add_p3.input_source_a0 = "DATAA",
the_altmult_add_p3.input_source_b0 = "DATAB",
the_altmult_add_p3.lpm_type = "altera_mult_add",
the_altmult_add_p3.multiplier1_direction = "ADD",
the_altmult_add_p3.multiplier_aclr0 = "ACLR0",
the_altmult_add_p3.multiplier_register0 = "CLOCK0",
the_altmult_add_p3.number_of_multipliers = 1,
the_altmult_add_p3.output_register = "UNREGISTERED",
the_altmult_add_p3.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p3.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p3.representation_a = "UNSIGNED",
the_altmult_add_p3.representation_b = "UNSIGNED",
the_altmult_add_p3.selected_device_family = "CYCLONEV",
the_altmult_add_p3.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p3.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p3.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p3.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p3.signed_register_a = "UNREGISTERED",
the_altmult_add_p3.signed_register_b = "UNREGISTERED",
the_altmult_add_p3.width_a = 16,
the_altmult_add_p3.width_b = 16,
the_altmult_add_p3.width_result = 32;
endmodule
|
//Legal Notice: (C)2017 Altera Corporation. All rights reserved. Your
//use of Altera Corporation's design tools, logic functions and other
//software and tools, and its AMPP partner logic functions, and any
//output files any of the foregoing (including device programming or
//simulation files), and any associated documentation or information are
//expressly subject to the terms and conditions of the Altera Program
//License Subscription Agreement or other applicable license agreement,
//including, without limitation, that your use is for the sole purpose
//of programming logic devices manufactured by Altera and sold by Altera
//or its authorized distributors. Please refer to the applicable
//agreement for further details.
// synthesis translate_off
`timescale 1ns / 1ps
// synthesis translate_on
// turn off superfluous verilog processor warnings
// altera message_level Level1
// altera message_off 10034 10035 10036 10037 10230 10240 10030
module soc_design_niosII_core_cpu_mult_cell (
// inputs:
E_src1,
E_src2,
M_en,
clk,
reset_n,
// outputs:
M_mul_cell_p1,
M_mul_cell_p2,
M_mul_cell_p3
)
;
output [ 31: 0] M_mul_cell_p1;
output [ 31: 0] M_mul_cell_p2;
output [ 31: 0] M_mul_cell_p3;
input [ 31: 0] E_src1;
input [ 31: 0] E_src2;
input M_en;
input clk;
input reset_n;
wire [ 31: 0] M_mul_cell_p1;
wire [ 31: 0] M_mul_cell_p2;
wire [ 31: 0] M_mul_cell_p3;
wire mul_clr;
wire [ 31: 0] mul_src1;
wire [ 31: 0] mul_src2;
assign mul_clr = ~reset_n;
assign mul_src1 = E_src1;
assign mul_src2 = E_src2;
altera_mult_add the_altmult_add_p1
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p1)
);
defparam the_altmult_add_p1.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p1.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p1.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p1.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p1.input_register_a0 = "UNREGISTERED",
the_altmult_add_p1.input_register_b0 = "UNREGISTERED",
the_altmult_add_p1.input_source_a0 = "DATAA",
the_altmult_add_p1.input_source_b0 = "DATAB",
the_altmult_add_p1.lpm_type = "altera_mult_add",
the_altmult_add_p1.multiplier1_direction = "ADD",
the_altmult_add_p1.multiplier_aclr0 = "ACLR0",
the_altmult_add_p1.multiplier_register0 = "CLOCK0",
the_altmult_add_p1.number_of_multipliers = 1,
the_altmult_add_p1.output_register = "UNREGISTERED",
the_altmult_add_p1.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p1.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p1.representation_a = "UNSIGNED",
the_altmult_add_p1.representation_b = "UNSIGNED",
the_altmult_add_p1.selected_device_family = "CYCLONEV",
the_altmult_add_p1.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p1.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p1.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p1.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p1.signed_register_a = "UNREGISTERED",
the_altmult_add_p1.signed_register_b = "UNREGISTERED",
the_altmult_add_p1.width_a = 16,
the_altmult_add_p1.width_b = 16,
the_altmult_add_p1.width_result = 32;
altera_mult_add the_altmult_add_p2
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[15 : 0]),
.datab (mul_src2[31 : 16]),
.ena0 (M_en),
.result (M_mul_cell_p2)
);
defparam the_altmult_add_p2.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p2.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p2.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p2.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p2.input_register_a0 = "UNREGISTERED",
the_altmult_add_p2.input_register_b0 = "UNREGISTERED",
the_altmult_add_p2.input_source_a0 = "DATAA",
the_altmult_add_p2.input_source_b0 = "DATAB",
the_altmult_add_p2.lpm_type = "altera_mult_add",
the_altmult_add_p2.multiplier1_direction = "ADD",
the_altmult_add_p2.multiplier_aclr0 = "ACLR0",
the_altmult_add_p2.multiplier_register0 = "CLOCK0",
the_altmult_add_p2.number_of_multipliers = 1,
the_altmult_add_p2.output_register = "UNREGISTERED",
the_altmult_add_p2.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p2.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p2.representation_a = "UNSIGNED",
the_altmult_add_p2.representation_b = "UNSIGNED",
the_altmult_add_p2.selected_device_family = "CYCLONEV",
the_altmult_add_p2.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p2.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p2.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p2.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p2.signed_register_a = "UNREGISTERED",
the_altmult_add_p2.signed_register_b = "UNREGISTERED",
the_altmult_add_p2.width_a = 16,
the_altmult_add_p2.width_b = 16,
the_altmult_add_p2.width_result = 32;
altera_mult_add the_altmult_add_p3
(
.aclr0 (mul_clr),
.clock0 (clk),
.dataa (mul_src1[31 : 16]),
.datab (mul_src2[15 : 0]),
.ena0 (M_en),
.result (M_mul_cell_p3)
);
defparam the_altmult_add_p3.addnsub_multiplier_pipeline_aclr1 = "ACLR0",
the_altmult_add_p3.addnsub_multiplier_pipeline_register1 = "CLOCK0",
the_altmult_add_p3.addnsub_multiplier_register1 = "UNREGISTERED",
the_altmult_add_p3.dedicated_multiplier_circuitry = "YES",
the_altmult_add_p3.input_register_a0 = "UNREGISTERED",
the_altmult_add_p3.input_register_b0 = "UNREGISTERED",
the_altmult_add_p3.input_source_a0 = "DATAA",
the_altmult_add_p3.input_source_b0 = "DATAB",
the_altmult_add_p3.lpm_type = "altera_mult_add",
the_altmult_add_p3.multiplier1_direction = "ADD",
the_altmult_add_p3.multiplier_aclr0 = "ACLR0",
the_altmult_add_p3.multiplier_register0 = "CLOCK0",
the_altmult_add_p3.number_of_multipliers = 1,
the_altmult_add_p3.output_register = "UNREGISTERED",
the_altmult_add_p3.port_addnsub1 = "PORT_UNUSED",
the_altmult_add_p3.port_addnsub3 = "PORT_UNUSED",
the_altmult_add_p3.representation_a = "UNSIGNED",
the_altmult_add_p3.representation_b = "UNSIGNED",
the_altmult_add_p3.selected_device_family = "CYCLONEV",
the_altmult_add_p3.signed_pipeline_aclr_a = "ACLR0",
the_altmult_add_p3.signed_pipeline_aclr_b = "ACLR0",
the_altmult_add_p3.signed_pipeline_register_a = "CLOCK0",
the_altmult_add_p3.signed_pipeline_register_b = "CLOCK0",
the_altmult_add_p3.signed_register_a = "UNREGISTERED",
the_altmult_add_p3.signed_register_b = "UNREGISTERED",
the_altmult_add_p3.width_a = 16,
the_altmult_add_p3.width_b = 16,
the_altmult_add_p3.width_result = 32;
endmodule
|
/*
* Copyright (c) 2009 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule
|
/*
* Copyright (c) 2009 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule
|
/*
* Copyright (c) 2009 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule
|
/*
* Copyright (c) 2009 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule
|
/*
* Copyright (c) 2009 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule
|
/*
* Copyright (c) 2009 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule
|
/*
* Copyright (c) 2009 Zeus Gomez Marmolejo <[email protected]>
*
* This file is part of the Zet processor. This processor is free
* hardware; you can redistribute it and/or modify it under the terms of
* the GNU General Public License as published by the Free Software
* Foundation; either version 3, or (at your option) any later version.
*
* Zet is distrubuted in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
* License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Zet; see the file COPYING. If not, see
* <http://www.gnu.org/licenses/>.
*/
module hex_display (
input [15:0] num,
input en,
output [6:0] hex0,
output [6:0] hex1,
output [6:0] hex2,
output [6:0] hex3
);
// Module instantiations
seg_7 hex_group0 (
.num (num[3:0]),
.en (en),
.seg (hex0)
);
seg_7 hex_group1 (
.num (num[7:4]),
.en (en),
.seg (hex1)
);
seg_7 hex_group2 (
.num (num[11:8]),
.en (en),
.seg (hex2)
);
seg_7 hex_group3 (
.num (num[15:12]),
.en (en),
.seg (hex3)
);
endmodule
|
// (c) Copyright 2012-2013 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Description: SRL based FIFO for AXIS/AXI Channels.
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_infrastructure_v1_1_axic_srl_fifo #(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
parameter C_FAMILY = "virtex7",
parameter integer C_PAYLOAD_WIDTH = 1,
parameter integer C_FIFO_DEPTH = 16 // Range: 4-16.
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire aclk, // Clock
input wire aresetn, // Reset
input wire [C_PAYLOAD_WIDTH-1:0] s_payload, // Input data
input wire s_valid, // Input data valid
output reg s_ready, // Input data ready
output wire [C_PAYLOAD_WIDTH-1:0] m_payload, // Output data
output reg m_valid, // Output data valid
input wire m_ready // Output data ready
);
////////////////////////////////////////////////////////////////////////////////
// Functions
////////////////////////////////////////////////////////////////////////////////
// ceiling logb2
function integer f_clogb2 (input integer size);
integer s;
begin
s = size;
s = s - 1;
for (f_clogb2=1; s>1; f_clogb2=f_clogb2+1)
s = s >> 1;
end
endfunction // clogb2
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
localparam integer LP_LOG_FIFO_DEPTH = f_clogb2(C_FIFO_DEPTH);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [LP_LOG_FIFO_DEPTH-1:0] fifo_index;
wire [4-1:0] fifo_addr;
wire push;
wire pop ;
reg areset_r1;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
always @(posedge aclk) begin
areset_r1 <= ~aresetn;
end
always @(posedge aclk) begin
if (~aresetn) begin
fifo_index <= {LP_LOG_FIFO_DEPTH{1'b1}};
end
else begin
fifo_index <= push & ~pop ? fifo_index + 1'b1 :
~push & pop ? fifo_index - 1'b1 :
fifo_index;
end
end
assign push = s_valid & s_ready;
always @(posedge aclk) begin
if (~aresetn) begin
s_ready <= 1'b0;
end
else begin
s_ready <= areset_r1 ? 1'b1 :
push & ~pop && (fifo_index == (C_FIFO_DEPTH - 2'd2)) ? 1'b0 :
~push & pop ? 1'b1 :
s_ready;
end
end
assign pop = m_valid & m_ready;
always @(posedge aclk) begin
if (~aresetn) begin
m_valid <= 1'b0;
end
else begin
m_valid <= ~push & pop && (fifo_index == {LP_LOG_FIFO_DEPTH{1'b0}}) ? 1'b0 :
push & ~pop ? 1'b1 :
m_valid;
end
end
generate
if (LP_LOG_FIFO_DEPTH < 4) begin : gen_pad_fifo_addr
assign fifo_addr[0+:LP_LOG_FIFO_DEPTH] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
assign fifo_addr[LP_LOG_FIFO_DEPTH+:(4-LP_LOG_FIFO_DEPTH)] = {4-LP_LOG_FIFO_DEPTH{1'b0}};
end
else begin : gen_fifo_addr
assign fifo_addr[LP_LOG_FIFO_DEPTH-1:0] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
end
endgenerate
generate
genvar i;
for (i = 0; i < C_PAYLOAD_WIDTH; i = i + 1) begin : gen_data_bit
SRL16E
u_srl_fifo(
.Q ( m_payload[i] ) ,
.A0 ( fifo_addr[0] ) ,
.A1 ( fifo_addr[1] ) ,
.A2 ( fifo_addr[2] ) ,
.A3 ( fifo_addr[3] ) ,
.CE ( push ) ,
.CLK ( aclk ) ,
.D ( s_payload[i] )
);
end
endgenerate
endmodule
`default_nettype wire
|
// (c) Copyright 2012-2013 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Description: SRL based FIFO for AXIS/AXI Channels.
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_infrastructure_v1_1_axic_srl_fifo #(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
parameter C_FAMILY = "virtex7",
parameter integer C_PAYLOAD_WIDTH = 1,
parameter integer C_FIFO_DEPTH = 16 // Range: 4-16.
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire aclk, // Clock
input wire aresetn, // Reset
input wire [C_PAYLOAD_WIDTH-1:0] s_payload, // Input data
input wire s_valid, // Input data valid
output reg s_ready, // Input data ready
output wire [C_PAYLOAD_WIDTH-1:0] m_payload, // Output data
output reg m_valid, // Output data valid
input wire m_ready // Output data ready
);
////////////////////////////////////////////////////////////////////////////////
// Functions
////////////////////////////////////////////////////////////////////////////////
// ceiling logb2
function integer f_clogb2 (input integer size);
integer s;
begin
s = size;
s = s - 1;
for (f_clogb2=1; s>1; f_clogb2=f_clogb2+1)
s = s >> 1;
end
endfunction // clogb2
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
localparam integer LP_LOG_FIFO_DEPTH = f_clogb2(C_FIFO_DEPTH);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [LP_LOG_FIFO_DEPTH-1:0] fifo_index;
wire [4-1:0] fifo_addr;
wire push;
wire pop ;
reg areset_r1;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
always @(posedge aclk) begin
areset_r1 <= ~aresetn;
end
always @(posedge aclk) begin
if (~aresetn) begin
fifo_index <= {LP_LOG_FIFO_DEPTH{1'b1}};
end
else begin
fifo_index <= push & ~pop ? fifo_index + 1'b1 :
~push & pop ? fifo_index - 1'b1 :
fifo_index;
end
end
assign push = s_valid & s_ready;
always @(posedge aclk) begin
if (~aresetn) begin
s_ready <= 1'b0;
end
else begin
s_ready <= areset_r1 ? 1'b1 :
push & ~pop && (fifo_index == (C_FIFO_DEPTH - 2'd2)) ? 1'b0 :
~push & pop ? 1'b1 :
s_ready;
end
end
assign pop = m_valid & m_ready;
always @(posedge aclk) begin
if (~aresetn) begin
m_valid <= 1'b0;
end
else begin
m_valid <= ~push & pop && (fifo_index == {LP_LOG_FIFO_DEPTH{1'b0}}) ? 1'b0 :
push & ~pop ? 1'b1 :
m_valid;
end
end
generate
if (LP_LOG_FIFO_DEPTH < 4) begin : gen_pad_fifo_addr
assign fifo_addr[0+:LP_LOG_FIFO_DEPTH] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
assign fifo_addr[LP_LOG_FIFO_DEPTH+:(4-LP_LOG_FIFO_DEPTH)] = {4-LP_LOG_FIFO_DEPTH{1'b0}};
end
else begin : gen_fifo_addr
assign fifo_addr[LP_LOG_FIFO_DEPTH-1:0] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
end
endgenerate
generate
genvar i;
for (i = 0; i < C_PAYLOAD_WIDTH; i = i + 1) begin : gen_data_bit
SRL16E
u_srl_fifo(
.Q ( m_payload[i] ) ,
.A0 ( fifo_addr[0] ) ,
.A1 ( fifo_addr[1] ) ,
.A2 ( fifo_addr[2] ) ,
.A3 ( fifo_addr[3] ) ,
.CE ( push ) ,
.CLK ( aclk ) ,
.D ( s_payload[i] )
);
end
endgenerate
endmodule
`default_nettype wire
|
// (c) Copyright 2012-2013 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Description: SRL based FIFO for AXIS/AXI Channels.
//--------------------------------------------------------------------------
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_infrastructure_v1_1_axic_srl_fifo #(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
parameter C_FAMILY = "virtex7",
parameter integer C_PAYLOAD_WIDTH = 1,
parameter integer C_FIFO_DEPTH = 16 // Range: 4-16.
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
input wire aclk, // Clock
input wire aresetn, // Reset
input wire [C_PAYLOAD_WIDTH-1:0] s_payload, // Input data
input wire s_valid, // Input data valid
output reg s_ready, // Input data ready
output wire [C_PAYLOAD_WIDTH-1:0] m_payload, // Output data
output reg m_valid, // Output data valid
input wire m_ready // Output data ready
);
////////////////////////////////////////////////////////////////////////////////
// Functions
////////////////////////////////////////////////////////////////////////////////
// ceiling logb2
function integer f_clogb2 (input integer size);
integer s;
begin
s = size;
s = s - 1;
for (f_clogb2=1; s>1; f_clogb2=f_clogb2+1)
s = s >> 1;
end
endfunction // clogb2
////////////////////////////////////////////////////////////////////////////////
// Local parameters
////////////////////////////////////////////////////////////////////////////////
localparam integer LP_LOG_FIFO_DEPTH = f_clogb2(C_FIFO_DEPTH);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
reg [LP_LOG_FIFO_DEPTH-1:0] fifo_index;
wire [4-1:0] fifo_addr;
wire push;
wire pop ;
reg areset_r1;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
always @(posedge aclk) begin
areset_r1 <= ~aresetn;
end
always @(posedge aclk) begin
if (~aresetn) begin
fifo_index <= {LP_LOG_FIFO_DEPTH{1'b1}};
end
else begin
fifo_index <= push & ~pop ? fifo_index + 1'b1 :
~push & pop ? fifo_index - 1'b1 :
fifo_index;
end
end
assign push = s_valid & s_ready;
always @(posedge aclk) begin
if (~aresetn) begin
s_ready <= 1'b0;
end
else begin
s_ready <= areset_r1 ? 1'b1 :
push & ~pop && (fifo_index == (C_FIFO_DEPTH - 2'd2)) ? 1'b0 :
~push & pop ? 1'b1 :
s_ready;
end
end
assign pop = m_valid & m_ready;
always @(posedge aclk) begin
if (~aresetn) begin
m_valid <= 1'b0;
end
else begin
m_valid <= ~push & pop && (fifo_index == {LP_LOG_FIFO_DEPTH{1'b0}}) ? 1'b0 :
push & ~pop ? 1'b1 :
m_valid;
end
end
generate
if (LP_LOG_FIFO_DEPTH < 4) begin : gen_pad_fifo_addr
assign fifo_addr[0+:LP_LOG_FIFO_DEPTH] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
assign fifo_addr[LP_LOG_FIFO_DEPTH+:(4-LP_LOG_FIFO_DEPTH)] = {4-LP_LOG_FIFO_DEPTH{1'b0}};
end
else begin : gen_fifo_addr
assign fifo_addr[LP_LOG_FIFO_DEPTH-1:0] = fifo_index[LP_LOG_FIFO_DEPTH-1:0];
end
endgenerate
generate
genvar i;
for (i = 0; i < C_PAYLOAD_WIDTH; i = i + 1) begin : gen_data_bit
SRL16E
u_srl_fifo(
.Q ( m_payload[i] ) ,
.A0 ( fifo_addr[0] ) ,
.A1 ( fifo_addr[1] ) ,
.A2 ( fifo_addr[2] ) ,
.A3 ( fifo_addr[3] ) ,
.CE ( push ) ,
.CLK ( aclk ) ,
.D ( s_payload[i] )
);
end
endgenerate
endmodule
`default_nettype wire
|
`include "hi_read_tx.v"
/*
pck0 - input main 24Mhz clock (PLL / 4)
[7:0] adc_d - input data from A/D converter
shallow_modulation - modulation type
pwr_lo - output to coil drivers (ssp_clk / 8)
adc_clk - output A/D clock signal
ssp_frame - output SSS frame indicator (goes high while the 8 bits are shifted)
ssp_din - output SSP data to ARM (shifts 8 bit A/D value serially to ARM MSB first)
ssp_clk - output SSP clock signal
ck_1356meg - input unused
ck_1356megb - input unused
ssp_dout - input unused
cross_hi - input unused
cross_lo - input unused
pwr_hi - output unused, tied low
pwr_oe1 - output unused, undefined
pwr_oe2 - output unused, undefined
pwr_oe3 - output unused, undefined
pwr_oe4 - output unused, undefined
dbg - output alias for adc_clk
*/
module testbed_hi_read_tx;
reg pck0;
reg [7:0] adc_d;
reg shallow_modulation;
wire pwr_lo;
wire adc_clk;
reg ck_1356meg;
reg ck_1356megb;
wire ssp_frame;
wire ssp_din;
wire ssp_clk;
reg ssp_dout;
wire pwr_hi;
wire pwr_oe1;
wire pwr_oe2;
wire pwr_oe3;
wire pwr_oe4;
wire cross_lo;
wire cross_hi;
wire dbg;
hi_read_tx #(5,200) dut(
.pck0(pck0),
.ck_1356meg(ck_1356meg),
.ck_1356megb(ck_1356megb),
.pwr_lo(pwr_lo),
.pwr_hi(pwr_hi),
.pwr_oe1(pwr_oe1),
.pwr_oe2(pwr_oe2),
.pwr_oe3(pwr_oe3),
.pwr_oe4(pwr_oe4),
.adc_d(adc_d),
.adc_clk(adc_clk),
.ssp_frame(ssp_frame),
.ssp_din(ssp_din),
.ssp_dout(ssp_dout),
.ssp_clk(ssp_clk),
.cross_hi(cross_hi),
.cross_lo(cross_lo),
.dbg(dbg),
.shallow_modulation(shallow_modulation)
);
integer idx, i;
// main clock
always #5 begin
ck_1356megb = !ck_1356megb;
ck_1356meg = ck_1356megb;
end
//crank DUT
task crank_dut;
begin
@(posedge ssp_clk) ;
ssp_dout = $random;
end
endtask
initial begin
// init inputs
ck_1356megb = 0;
adc_d = 0;
ssp_dout=0;
// shallow modulation off
shallow_modulation=0;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
// shallow modulation on
shallow_modulation=1;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
$finish;
end
endmodule // main
|
`include "hi_read_tx.v"
/*
pck0 - input main 24Mhz clock (PLL / 4)
[7:0] adc_d - input data from A/D converter
shallow_modulation - modulation type
pwr_lo - output to coil drivers (ssp_clk / 8)
adc_clk - output A/D clock signal
ssp_frame - output SSS frame indicator (goes high while the 8 bits are shifted)
ssp_din - output SSP data to ARM (shifts 8 bit A/D value serially to ARM MSB first)
ssp_clk - output SSP clock signal
ck_1356meg - input unused
ck_1356megb - input unused
ssp_dout - input unused
cross_hi - input unused
cross_lo - input unused
pwr_hi - output unused, tied low
pwr_oe1 - output unused, undefined
pwr_oe2 - output unused, undefined
pwr_oe3 - output unused, undefined
pwr_oe4 - output unused, undefined
dbg - output alias for adc_clk
*/
module testbed_hi_read_tx;
reg pck0;
reg [7:0] adc_d;
reg shallow_modulation;
wire pwr_lo;
wire adc_clk;
reg ck_1356meg;
reg ck_1356megb;
wire ssp_frame;
wire ssp_din;
wire ssp_clk;
reg ssp_dout;
wire pwr_hi;
wire pwr_oe1;
wire pwr_oe2;
wire pwr_oe3;
wire pwr_oe4;
wire cross_lo;
wire cross_hi;
wire dbg;
hi_read_tx #(5,200) dut(
.pck0(pck0),
.ck_1356meg(ck_1356meg),
.ck_1356megb(ck_1356megb),
.pwr_lo(pwr_lo),
.pwr_hi(pwr_hi),
.pwr_oe1(pwr_oe1),
.pwr_oe2(pwr_oe2),
.pwr_oe3(pwr_oe3),
.pwr_oe4(pwr_oe4),
.adc_d(adc_d),
.adc_clk(adc_clk),
.ssp_frame(ssp_frame),
.ssp_din(ssp_din),
.ssp_dout(ssp_dout),
.ssp_clk(ssp_clk),
.cross_hi(cross_hi),
.cross_lo(cross_lo),
.dbg(dbg),
.shallow_modulation(shallow_modulation)
);
integer idx, i;
// main clock
always #5 begin
ck_1356megb = !ck_1356megb;
ck_1356meg = ck_1356megb;
end
//crank DUT
task crank_dut;
begin
@(posedge ssp_clk) ;
ssp_dout = $random;
end
endtask
initial begin
// init inputs
ck_1356megb = 0;
adc_d = 0;
ssp_dout=0;
// shallow modulation off
shallow_modulation=0;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
// shallow modulation on
shallow_modulation=1;
for (i = 0 ; i < 16 ; i = i + 1) begin
crank_dut;
end
$finish;
end
endmodule // main
|
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s_aw_channel #
(
///////////////////////////////////////////////////////////////////////////////
// Parameter Definitions
///////////////////////////////////////////////////////////////////////////////
// Width of ID signals.
// Range: >= 1.
parameter integer C_ID_WIDTH = 4,
// Width of AxADDR
// Range: 32.
parameter integer C_AXI_ADDR_WIDTH = 32
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
// AXI Slave Interface
// Slave Interface System Signals
input wire clk ,
input wire reset ,
// Slave Interface Write Address Ports
input wire [C_ID_WIDTH-1:0] s_awid ,
input wire [C_AXI_ADDR_WIDTH-1:0] s_awaddr ,
input wire [7:0] s_awlen ,
input wire [2:0] s_awsize ,
input wire [1:0] s_awburst ,
input wire s_awvalid ,
output wire s_awready ,
output wire m_awvalid ,
output wire [C_AXI_ADDR_WIDTH-1:0] m_awaddr ,
input wire m_awready ,
// Connections to/from axi_protocol_converter_v2_1_b2s_b_channel module
output wire b_push ,
output wire [C_ID_WIDTH-1:0] b_awid ,
output wire [7:0] b_awlen ,
input wire b_full
);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
wire next ;
wire next_pending ;
wire a_push;
wire incr_burst;
reg [C_ID_WIDTH-1:0] s_awid_r;
reg [7:0] s_awlen_r;
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
////////////////////////////////////////////////////////////////////////////////
// Translate the AXI transaction to the MC transaction(s)
axi_protocol_converter_v2_1_b2s_cmd_translator #
(
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH )
)
cmd_translator_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_axaddr ( s_awaddr ) ,
.s_axlen ( s_awlen ) ,
.s_axsize ( s_awsize ) ,
.s_axburst ( s_awburst ) ,
.s_axhandshake ( s_awvalid & a_push ) ,
.m_axaddr ( m_awaddr ) ,
.incr_burst ( incr_burst ) ,
.next ( next ) ,
.next_pending ( next_pending )
);
axi_protocol_converter_v2_1_b2s_wr_cmd_fsm aw_cmd_fsm_0
(
.clk ( clk ) ,
.reset ( reset ) ,
.s_awready ( s_awready ) ,
.s_awvalid ( s_awvalid ) ,
.m_awvalid ( m_awvalid ) ,
.m_awready ( m_awready ) ,
.next ( next ) ,
.next_pending ( next_pending ) ,
.b_push ( b_push ) ,
.b_full ( b_full ) ,
.a_push ( a_push )
);
assign b_awid = s_awid_r;
assign b_awlen = s_awlen_r;
always @(posedge clk) begin
s_awid_r <= s_awid ;
s_awlen_r <= s_awlen ;
end
endmodule
`default_nettype wire
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/17/2016 05:20:59 PM
// Design Name:
// Module Name: Priority_Codec_64
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Priority_Codec_64(
input wire [54:0] Data_Dec_i,
output reg [5:0] Data_Bin_o
);
always @(Data_Dec_i)
begin
Data_Bin_o=6'b000000;
if(~Data_Dec_i[54]) begin Data_Bin_o = 6'b000000;//0
end else if(~Data_Dec_i[53]) begin Data_Bin_o = 6'b000001;//1
end else if(~Data_Dec_i[52]) begin Data_Bin_o = 6'b000010;//2
end else if(~Data_Dec_i[51]) begin Data_Bin_o = 6'b000011;//3
end else if(~Data_Dec_i[50]) begin Data_Bin_o = 6'b000100;//4
end else if(~Data_Dec_i[49]) begin Data_Bin_o = 6'b000101;//5
end else if(~Data_Dec_i[48]) begin Data_Bin_o = 6'b000110;//6
end else if(~Data_Dec_i[47]) begin Data_Bin_o = 6'b000111;//7
end else if(~Data_Dec_i[46]) begin Data_Bin_o = 6'b001000;//8
end else if(~Data_Dec_i[45]) begin Data_Bin_o = 6'b001001;//9
end else if(~Data_Dec_i[44]) begin Data_Bin_o = 6'b001010;//10
end else if(~Data_Dec_i[43]) begin Data_Bin_o = 6'b001011;//11
end else if(~Data_Dec_i[42]) begin Data_Bin_o = 6'b001100;//12
end else if(~Data_Dec_i[41]) begin Data_Bin_o = 6'b001101;//13
end else if(~Data_Dec_i[40]) begin Data_Bin_o = 6'b001110;//14
end else if(~Data_Dec_i[39]) begin Data_Bin_o = 6'b001111;//15
end else if(~Data_Dec_i[38]) begin Data_Bin_o = 6'b010000;//16
end else if(~Data_Dec_i[37]) begin Data_Bin_o = 6'b010001;//17
end else if(~Data_Dec_i[36]) begin Data_Bin_o = 6'b010010;//18
end else if(~Data_Dec_i[35]) begin Data_Bin_o = 6'b010011;//19
end else if(~Data_Dec_i[34]) begin Data_Bin_o = 6'b010100;//20
end else if(~Data_Dec_i[33]) begin Data_Bin_o = 6'b010101;//21
end else if(~Data_Dec_i[32]) begin Data_Bin_o = 6'b010110;//22
end else if(~Data_Dec_i[31]) begin Data_Bin_o = 6'b010111;//23
end else if(~Data_Dec_i[30]) begin Data_Bin_o = 6'b011000;//24
end else if(~Data_Dec_i[29]) begin Data_Bin_o = 6'b010101;//25
end else if(~Data_Dec_i[28]) begin Data_Bin_o = 6'b010110;//26
end else if(~Data_Dec_i[27]) begin Data_Bin_o = 6'b010111;//27
end else if(~Data_Dec_i[26]) begin Data_Bin_o = 6'b011000;//28
end else if(~Data_Dec_i[25]) begin Data_Bin_o = 6'b011001;//29
end else if(~Data_Dec_i[24]) begin Data_Bin_o = 6'b011010;//30
end else if(~Data_Dec_i[23]) begin Data_Bin_o = 6'b011011;//31
end else if(~Data_Dec_i[22]) begin Data_Bin_o = 6'b011100;//32
end else if(~Data_Dec_i[21]) begin Data_Bin_o = 6'b011101;//33
end else if(~Data_Dec_i[20]) begin Data_Bin_o = 6'b011110;//34
end else if(~Data_Dec_i[19]) begin Data_Bin_o = 6'b011111;//35
end else if(~Data_Dec_i[18]) begin Data_Bin_o = 6'b100000;//36
end else if(~Data_Dec_i[17]) begin Data_Bin_o = 6'b100001;//37
end else if(~Data_Dec_i[16]) begin Data_Bin_o = 6'b100010;//38
end else if(~Data_Dec_i[15]) begin Data_Bin_o = 6'b100011;//39
end else if(~Data_Dec_i[14]) begin Data_Bin_o = 6'b100100;//40
end else if(~Data_Dec_i[13]) begin Data_Bin_o = 6'b100101;//41
end else if(~Data_Dec_i[12]) begin Data_Bin_o = 6'b100110;//42
end else if(~Data_Dec_i[11]) begin Data_Bin_o = 6'b100111;//43
end else if(~Data_Dec_i[10]) begin Data_Bin_o = 6'b101000;//44
end else if(~Data_Dec_i[9]) begin Data_Bin_o = 6'b101001;//45
end else if(~Data_Dec_i[8]) begin Data_Bin_o = 6'b101010;//46
end else if(~Data_Dec_i[7]) begin Data_Bin_o = 6'b101011;//47
end else if(~Data_Dec_i[6]) begin Data_Bin_o = 6'b101100;//48
end else if(~Data_Dec_i[5]) begin Data_Bin_o = 6'b101101;//49
end else if(~Data_Dec_i[4]) begin Data_Bin_o = 6'b101110;//50
end else if(~Data_Dec_i[3]) begin Data_Bin_o = 6'b101111;//51
end else if(~Data_Dec_i[2]) begin Data_Bin_o = 6'b110000;//52
end else if(~Data_Dec_i[1]) begin Data_Bin_o = 6'b110001;//53
end else if(~Data_Dec_i[0]) begin Data_Bin_o = 6'b110010;//54
end else begin Data_Bin_o = 6'b000000;//zero value
end
end
endmodule |
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/17/2016 05:20:59 PM
// Design Name:
// Module Name: Priority_Codec_64
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Priority_Codec_64(
input wire [54:0] Data_Dec_i,
output reg [5:0] Data_Bin_o
);
always @(Data_Dec_i)
begin
Data_Bin_o=6'b000000;
if(~Data_Dec_i[54]) begin Data_Bin_o = 6'b000000;//0
end else if(~Data_Dec_i[53]) begin Data_Bin_o = 6'b000001;//1
end else if(~Data_Dec_i[52]) begin Data_Bin_o = 6'b000010;//2
end else if(~Data_Dec_i[51]) begin Data_Bin_o = 6'b000011;//3
end else if(~Data_Dec_i[50]) begin Data_Bin_o = 6'b000100;//4
end else if(~Data_Dec_i[49]) begin Data_Bin_o = 6'b000101;//5
end else if(~Data_Dec_i[48]) begin Data_Bin_o = 6'b000110;//6
end else if(~Data_Dec_i[47]) begin Data_Bin_o = 6'b000111;//7
end else if(~Data_Dec_i[46]) begin Data_Bin_o = 6'b001000;//8
end else if(~Data_Dec_i[45]) begin Data_Bin_o = 6'b001001;//9
end else if(~Data_Dec_i[44]) begin Data_Bin_o = 6'b001010;//10
end else if(~Data_Dec_i[43]) begin Data_Bin_o = 6'b001011;//11
end else if(~Data_Dec_i[42]) begin Data_Bin_o = 6'b001100;//12
end else if(~Data_Dec_i[41]) begin Data_Bin_o = 6'b001101;//13
end else if(~Data_Dec_i[40]) begin Data_Bin_o = 6'b001110;//14
end else if(~Data_Dec_i[39]) begin Data_Bin_o = 6'b001111;//15
end else if(~Data_Dec_i[38]) begin Data_Bin_o = 6'b010000;//16
end else if(~Data_Dec_i[37]) begin Data_Bin_o = 6'b010001;//17
end else if(~Data_Dec_i[36]) begin Data_Bin_o = 6'b010010;//18
end else if(~Data_Dec_i[35]) begin Data_Bin_o = 6'b010011;//19
end else if(~Data_Dec_i[34]) begin Data_Bin_o = 6'b010100;//20
end else if(~Data_Dec_i[33]) begin Data_Bin_o = 6'b010101;//21
end else if(~Data_Dec_i[32]) begin Data_Bin_o = 6'b010110;//22
end else if(~Data_Dec_i[31]) begin Data_Bin_o = 6'b010111;//23
end else if(~Data_Dec_i[30]) begin Data_Bin_o = 6'b011000;//24
end else if(~Data_Dec_i[29]) begin Data_Bin_o = 6'b010101;//25
end else if(~Data_Dec_i[28]) begin Data_Bin_o = 6'b010110;//26
end else if(~Data_Dec_i[27]) begin Data_Bin_o = 6'b010111;//27
end else if(~Data_Dec_i[26]) begin Data_Bin_o = 6'b011000;//28
end else if(~Data_Dec_i[25]) begin Data_Bin_o = 6'b011001;//29
end else if(~Data_Dec_i[24]) begin Data_Bin_o = 6'b011010;//30
end else if(~Data_Dec_i[23]) begin Data_Bin_o = 6'b011011;//31
end else if(~Data_Dec_i[22]) begin Data_Bin_o = 6'b011100;//32
end else if(~Data_Dec_i[21]) begin Data_Bin_o = 6'b011101;//33
end else if(~Data_Dec_i[20]) begin Data_Bin_o = 6'b011110;//34
end else if(~Data_Dec_i[19]) begin Data_Bin_o = 6'b011111;//35
end else if(~Data_Dec_i[18]) begin Data_Bin_o = 6'b100000;//36
end else if(~Data_Dec_i[17]) begin Data_Bin_o = 6'b100001;//37
end else if(~Data_Dec_i[16]) begin Data_Bin_o = 6'b100010;//38
end else if(~Data_Dec_i[15]) begin Data_Bin_o = 6'b100011;//39
end else if(~Data_Dec_i[14]) begin Data_Bin_o = 6'b100100;//40
end else if(~Data_Dec_i[13]) begin Data_Bin_o = 6'b100101;//41
end else if(~Data_Dec_i[12]) begin Data_Bin_o = 6'b100110;//42
end else if(~Data_Dec_i[11]) begin Data_Bin_o = 6'b100111;//43
end else if(~Data_Dec_i[10]) begin Data_Bin_o = 6'b101000;//44
end else if(~Data_Dec_i[9]) begin Data_Bin_o = 6'b101001;//45
end else if(~Data_Dec_i[8]) begin Data_Bin_o = 6'b101010;//46
end else if(~Data_Dec_i[7]) begin Data_Bin_o = 6'b101011;//47
end else if(~Data_Dec_i[6]) begin Data_Bin_o = 6'b101100;//48
end else if(~Data_Dec_i[5]) begin Data_Bin_o = 6'b101101;//49
end else if(~Data_Dec_i[4]) begin Data_Bin_o = 6'b101110;//50
end else if(~Data_Dec_i[3]) begin Data_Bin_o = 6'b101111;//51
end else if(~Data_Dec_i[2]) begin Data_Bin_o = 6'b110000;//52
end else if(~Data_Dec_i[1]) begin Data_Bin_o = 6'b110001;//53
end else if(~Data_Dec_i[0]) begin Data_Bin_o = 6'b110010;//54
end else begin Data_Bin_o = 6'b000000;//zero value
end
end
endmodule |
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/17/2016 05:20:59 PM
// Design Name:
// Module Name: Priority_Codec_64
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Priority_Codec_64(
input wire [54:0] Data_Dec_i,
output reg [5:0] Data_Bin_o
);
always @(Data_Dec_i)
begin
Data_Bin_o=6'b000000;
if(~Data_Dec_i[54]) begin Data_Bin_o = 6'b000000;//0
end else if(~Data_Dec_i[53]) begin Data_Bin_o = 6'b000001;//1
end else if(~Data_Dec_i[52]) begin Data_Bin_o = 6'b000010;//2
end else if(~Data_Dec_i[51]) begin Data_Bin_o = 6'b000011;//3
end else if(~Data_Dec_i[50]) begin Data_Bin_o = 6'b000100;//4
end else if(~Data_Dec_i[49]) begin Data_Bin_o = 6'b000101;//5
end else if(~Data_Dec_i[48]) begin Data_Bin_o = 6'b000110;//6
end else if(~Data_Dec_i[47]) begin Data_Bin_o = 6'b000111;//7
end else if(~Data_Dec_i[46]) begin Data_Bin_o = 6'b001000;//8
end else if(~Data_Dec_i[45]) begin Data_Bin_o = 6'b001001;//9
end else if(~Data_Dec_i[44]) begin Data_Bin_o = 6'b001010;//10
end else if(~Data_Dec_i[43]) begin Data_Bin_o = 6'b001011;//11
end else if(~Data_Dec_i[42]) begin Data_Bin_o = 6'b001100;//12
end else if(~Data_Dec_i[41]) begin Data_Bin_o = 6'b001101;//13
end else if(~Data_Dec_i[40]) begin Data_Bin_o = 6'b001110;//14
end else if(~Data_Dec_i[39]) begin Data_Bin_o = 6'b001111;//15
end else if(~Data_Dec_i[38]) begin Data_Bin_o = 6'b010000;//16
end else if(~Data_Dec_i[37]) begin Data_Bin_o = 6'b010001;//17
end else if(~Data_Dec_i[36]) begin Data_Bin_o = 6'b010010;//18
end else if(~Data_Dec_i[35]) begin Data_Bin_o = 6'b010011;//19
end else if(~Data_Dec_i[34]) begin Data_Bin_o = 6'b010100;//20
end else if(~Data_Dec_i[33]) begin Data_Bin_o = 6'b010101;//21
end else if(~Data_Dec_i[32]) begin Data_Bin_o = 6'b010110;//22
end else if(~Data_Dec_i[31]) begin Data_Bin_o = 6'b010111;//23
end else if(~Data_Dec_i[30]) begin Data_Bin_o = 6'b011000;//24
end else if(~Data_Dec_i[29]) begin Data_Bin_o = 6'b010101;//25
end else if(~Data_Dec_i[28]) begin Data_Bin_o = 6'b010110;//26
end else if(~Data_Dec_i[27]) begin Data_Bin_o = 6'b010111;//27
end else if(~Data_Dec_i[26]) begin Data_Bin_o = 6'b011000;//28
end else if(~Data_Dec_i[25]) begin Data_Bin_o = 6'b011001;//29
end else if(~Data_Dec_i[24]) begin Data_Bin_o = 6'b011010;//30
end else if(~Data_Dec_i[23]) begin Data_Bin_o = 6'b011011;//31
end else if(~Data_Dec_i[22]) begin Data_Bin_o = 6'b011100;//32
end else if(~Data_Dec_i[21]) begin Data_Bin_o = 6'b011101;//33
end else if(~Data_Dec_i[20]) begin Data_Bin_o = 6'b011110;//34
end else if(~Data_Dec_i[19]) begin Data_Bin_o = 6'b011111;//35
end else if(~Data_Dec_i[18]) begin Data_Bin_o = 6'b100000;//36
end else if(~Data_Dec_i[17]) begin Data_Bin_o = 6'b100001;//37
end else if(~Data_Dec_i[16]) begin Data_Bin_o = 6'b100010;//38
end else if(~Data_Dec_i[15]) begin Data_Bin_o = 6'b100011;//39
end else if(~Data_Dec_i[14]) begin Data_Bin_o = 6'b100100;//40
end else if(~Data_Dec_i[13]) begin Data_Bin_o = 6'b100101;//41
end else if(~Data_Dec_i[12]) begin Data_Bin_o = 6'b100110;//42
end else if(~Data_Dec_i[11]) begin Data_Bin_o = 6'b100111;//43
end else if(~Data_Dec_i[10]) begin Data_Bin_o = 6'b101000;//44
end else if(~Data_Dec_i[9]) begin Data_Bin_o = 6'b101001;//45
end else if(~Data_Dec_i[8]) begin Data_Bin_o = 6'b101010;//46
end else if(~Data_Dec_i[7]) begin Data_Bin_o = 6'b101011;//47
end else if(~Data_Dec_i[6]) begin Data_Bin_o = 6'b101100;//48
end else if(~Data_Dec_i[5]) begin Data_Bin_o = 6'b101101;//49
end else if(~Data_Dec_i[4]) begin Data_Bin_o = 6'b101110;//50
end else if(~Data_Dec_i[3]) begin Data_Bin_o = 6'b101111;//51
end else if(~Data_Dec_i[2]) begin Data_Bin_o = 6'b110000;//52
end else if(~Data_Dec_i[1]) begin Data_Bin_o = 6'b110001;//53
end else if(~Data_Dec_i[0]) begin Data_Bin_o = 6'b110010;//54
end else begin Data_Bin_o = 6'b000000;//zero value
end
end
endmodule |
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/17/2016 05:20:59 PM
// Design Name:
// Module Name: Priority_Codec_64
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Priority_Codec_64(
input wire [54:0] Data_Dec_i,
output reg [5:0] Data_Bin_o
);
always @(Data_Dec_i)
begin
Data_Bin_o=6'b000000;
if(~Data_Dec_i[54]) begin Data_Bin_o = 6'b000000;//0
end else if(~Data_Dec_i[53]) begin Data_Bin_o = 6'b000001;//1
end else if(~Data_Dec_i[52]) begin Data_Bin_o = 6'b000010;//2
end else if(~Data_Dec_i[51]) begin Data_Bin_o = 6'b000011;//3
end else if(~Data_Dec_i[50]) begin Data_Bin_o = 6'b000100;//4
end else if(~Data_Dec_i[49]) begin Data_Bin_o = 6'b000101;//5
end else if(~Data_Dec_i[48]) begin Data_Bin_o = 6'b000110;//6
end else if(~Data_Dec_i[47]) begin Data_Bin_o = 6'b000111;//7
end else if(~Data_Dec_i[46]) begin Data_Bin_o = 6'b001000;//8
end else if(~Data_Dec_i[45]) begin Data_Bin_o = 6'b001001;//9
end else if(~Data_Dec_i[44]) begin Data_Bin_o = 6'b001010;//10
end else if(~Data_Dec_i[43]) begin Data_Bin_o = 6'b001011;//11
end else if(~Data_Dec_i[42]) begin Data_Bin_o = 6'b001100;//12
end else if(~Data_Dec_i[41]) begin Data_Bin_o = 6'b001101;//13
end else if(~Data_Dec_i[40]) begin Data_Bin_o = 6'b001110;//14
end else if(~Data_Dec_i[39]) begin Data_Bin_o = 6'b001111;//15
end else if(~Data_Dec_i[38]) begin Data_Bin_o = 6'b010000;//16
end else if(~Data_Dec_i[37]) begin Data_Bin_o = 6'b010001;//17
end else if(~Data_Dec_i[36]) begin Data_Bin_o = 6'b010010;//18
end else if(~Data_Dec_i[35]) begin Data_Bin_o = 6'b010011;//19
end else if(~Data_Dec_i[34]) begin Data_Bin_o = 6'b010100;//20
end else if(~Data_Dec_i[33]) begin Data_Bin_o = 6'b010101;//21
end else if(~Data_Dec_i[32]) begin Data_Bin_o = 6'b010110;//22
end else if(~Data_Dec_i[31]) begin Data_Bin_o = 6'b010111;//23
end else if(~Data_Dec_i[30]) begin Data_Bin_o = 6'b011000;//24
end else if(~Data_Dec_i[29]) begin Data_Bin_o = 6'b010101;//25
end else if(~Data_Dec_i[28]) begin Data_Bin_o = 6'b010110;//26
end else if(~Data_Dec_i[27]) begin Data_Bin_o = 6'b010111;//27
end else if(~Data_Dec_i[26]) begin Data_Bin_o = 6'b011000;//28
end else if(~Data_Dec_i[25]) begin Data_Bin_o = 6'b011001;//29
end else if(~Data_Dec_i[24]) begin Data_Bin_o = 6'b011010;//30
end else if(~Data_Dec_i[23]) begin Data_Bin_o = 6'b011011;//31
end else if(~Data_Dec_i[22]) begin Data_Bin_o = 6'b011100;//32
end else if(~Data_Dec_i[21]) begin Data_Bin_o = 6'b011101;//33
end else if(~Data_Dec_i[20]) begin Data_Bin_o = 6'b011110;//34
end else if(~Data_Dec_i[19]) begin Data_Bin_o = 6'b011111;//35
end else if(~Data_Dec_i[18]) begin Data_Bin_o = 6'b100000;//36
end else if(~Data_Dec_i[17]) begin Data_Bin_o = 6'b100001;//37
end else if(~Data_Dec_i[16]) begin Data_Bin_o = 6'b100010;//38
end else if(~Data_Dec_i[15]) begin Data_Bin_o = 6'b100011;//39
end else if(~Data_Dec_i[14]) begin Data_Bin_o = 6'b100100;//40
end else if(~Data_Dec_i[13]) begin Data_Bin_o = 6'b100101;//41
end else if(~Data_Dec_i[12]) begin Data_Bin_o = 6'b100110;//42
end else if(~Data_Dec_i[11]) begin Data_Bin_o = 6'b100111;//43
end else if(~Data_Dec_i[10]) begin Data_Bin_o = 6'b101000;//44
end else if(~Data_Dec_i[9]) begin Data_Bin_o = 6'b101001;//45
end else if(~Data_Dec_i[8]) begin Data_Bin_o = 6'b101010;//46
end else if(~Data_Dec_i[7]) begin Data_Bin_o = 6'b101011;//47
end else if(~Data_Dec_i[6]) begin Data_Bin_o = 6'b101100;//48
end else if(~Data_Dec_i[5]) begin Data_Bin_o = 6'b101101;//49
end else if(~Data_Dec_i[4]) begin Data_Bin_o = 6'b101110;//50
end else if(~Data_Dec_i[3]) begin Data_Bin_o = 6'b101111;//51
end else if(~Data_Dec_i[2]) begin Data_Bin_o = 6'b110000;//52
end else if(~Data_Dec_i[1]) begin Data_Bin_o = 6'b110001;//53
end else if(~Data_Dec_i[0]) begin Data_Bin_o = 6'b110010;//54
end else begin Data_Bin_o = 6'b000000;//zero value
end
end
endmodule |
/* -*- verilog -*-
*
* USRP - Universal Software Radio Peripheral
*
* Copyright (C) 2005 Matt Ettus
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Boston, MA 02110-1301 USA
*/
/*
* This implements a 31-tap halfband filter that decimates by two.
* The coefficients are symmetric, and with the exception of the middle tap,
* every other coefficient is zero. The middle section of taps looks like this:
*
* ..., -1468, 0, 2950, 0, -6158, 0, 20585, 32768, 20585, 0, -6158, 0, 2950, 0, -1468, ...
* |
* middle tap -------+
*
* See coeff_rom.v for the full set. The taps are scaled relative to 32768,
* thus the middle tap equals 1.0. Not counting the middle tap, there are 8
* non-zero taps on each side, and they are symmetric. A naive implementation
* requires a mulitply for each non-zero tap. Because of symmetry, we can
* replace 2 multiplies with 1 add and 1 multiply. Thus, to compute each output
* sample, we need to perform 8 multiplications. Since the middle tap is 1.0,
* we just add the corresponding delay line value.
*
* About timing: We implement this with a single multiplier, so it takes
* 8 cycles to compute a single output. However, since we're decimating by two
* we can accept a new input value every 4 cycles. strobe_in is asserted when
* there's a new input sample available. Depending on the overall decimation
* rate, strobe_in may be asserted less frequently than once every 4 clocks.
* On the output side, we assert strobe_out when output contains a new sample.
*
* Implementation: Every time strobe_in is asserted we store the new data into
* the delay line. We split the delay line into two components, one for the
* even samples, and one for the odd samples. ram16_odd is the delay line for
* the odd samples. This ram is written on each odd assertion of strobe_in, and
* is read on each clock when we're computing the dot product. ram16_even is
* similar, although because it holds the even samples we must be able to read
* two samples from different addresses at the same time, while writing the incoming
* even samples. Thus it's "triple-ported".
*/
module halfband_decim
(input clock, input reset, input enable, input strobe_in, output wire strobe_out,
input wire [15:0] data_in, output reg [15:0] data_out,output wire [15:0] debugctrl);
reg [3:0] rd_addr1;
reg [3:0] rd_addr2;
reg [3:0] phase;
reg [3:0] base_addr;
wire signed [15:0] mac_out,middle_data, sum, coeff;
wire signed [30:0] product;
wire signed [33:0] sum_even;
wire clear;
reg store_odd;
always @(posedge clock)
if(reset)
store_odd <= #1 1'b0;
else
if(strobe_in)
store_odd <= #1 ~store_odd;
wire start = strobe_in & store_odd;
always @(posedge clock)
if(reset)
base_addr <= #1 4'd0;
else if(start)
base_addr <= #1 base_addr + 4'd1;
always @(posedge clock)
if(reset)
phase <= #1 4'd8;
else if (start)
phase <= #1 4'd0;
else if(phase != 4'd8)
phase <= #1 phase + 4'd1;
reg start_d1,start_d2,start_d3,start_d4,start_d5,start_d6,start_d7,start_d8,start_d9,start_dA,start_dB,start_dC,start_dD;
always @(posedge clock)
begin
start_d1 <= #1 start;
start_d2 <= #1 start_d1;
start_d3 <= #1 start_d2;
start_d4 <= #1 start_d3;
start_d5 <= #1 start_d4;
start_d6 <= #1 start_d5;
start_d7 <= #1 start_d6;
start_d8 <= #1 start_d7;
start_d9 <= #1 start_d8;
start_dA <= #1 start_d9;
start_dB <= #1 start_dA;
start_dC <= #1 start_dB;
start_dD <= #1 start_dC;
end // always @ (posedge clock)
reg mult_en, mult_en_pre;
always @(posedge clock)
begin
mult_en_pre <= #1 phase!=8;
mult_en <= #1 mult_en_pre;
end
assign clear = start_d4; // was dC
wire latch_result = start_d4; // was dC
assign strobe_out = start_d5; // was dD
wire acc_en;
always @*
case(phase[2:0])
3'd0 : begin rd_addr1 = base_addr + 4'd0; rd_addr2 = base_addr + 4'd15; end
3'd1 : begin rd_addr1 = base_addr + 4'd1; rd_addr2 = base_addr + 4'd14; end
3'd2 : begin rd_addr1 = base_addr + 4'd2; rd_addr2 = base_addr + 4'd13; end
3'd3 : begin rd_addr1 = base_addr + 4'd3; rd_addr2 = base_addr + 4'd12; end
3'd4 : begin rd_addr1 = base_addr + 4'd4; rd_addr2 = base_addr + 4'd11; end
3'd5 : begin rd_addr1 = base_addr + 4'd5; rd_addr2 = base_addr + 4'd10; end
3'd6 : begin rd_addr1 = base_addr + 4'd6; rd_addr2 = base_addr + 4'd9; end
3'd7 : begin rd_addr1 = base_addr + 4'd7; rd_addr2 = base_addr + 4'd8; end
default: begin rd_addr1 = base_addr + 4'd0; rd_addr2 = base_addr + 4'd15; end
endcase // case(phase)
coeff_rom coeff_rom (.clock(clock),.addr(phase[2:0]-3'd1),.data(coeff));
ram16_2sum ram16_even (.clock(clock),.write(strobe_in & ~store_odd),
.wr_addr(base_addr),.wr_data(data_in),
.rd_addr1(rd_addr1),.rd_addr2(rd_addr2),
.sum(sum));
ram16 ram16_odd (.clock(clock),.write(strobe_in & store_odd), // Holds middle items
.wr_addr(base_addr),.wr_data(data_in),
//.rd_addr(base_addr+4'd7),.rd_data(middle_data));
.rd_addr(base_addr+4'd6),.rd_data(middle_data));
mult mult(.clock(clock),.x(coeff),.y(sum),.product(product),.enable_in(mult_en),.enable_out(acc_en));
acc acc(.clock(clock),.reset(reset),.enable_in(acc_en),.enable_out(),
.clear(clear),.addend(product),.sum(sum_even));
wire signed [33:0] dout = sum_even + {{4{middle_data[15]}},middle_data,14'b0}; // We already divided product by 2!!!!
always @(posedge clock)
if(reset)
data_out <= #1 16'd0;
else if(latch_result)
data_out <= #1 dout[30:15] + (dout[33]& |dout[14:0]);
assign debugctrl = { clock,reset,acc_en,mult_en,clear,latch_result,store_odd,strobe_in,strobe_out,phase};
endmodule // halfband_decim
|
(***********************************************************************)
(* v * The Coq Proof Assistant / The Coq Development Team *)
(* <O___,, * INRIA-Rocquencourt & LRI-CNRS-Orsay *)
(* \VV/ *************************************************************)
(* // * This file is distributed under the terms of the *)
(* * GNU Lesser General Public License Version 2.1 *)
(***********************************************************************)
(** * Finite set library *)
(** Set interfaces, inspired by the one of Ocaml. When compared with
Ocaml, the main differences are:
- the lack of [iter] function, useless since Coq is purely functional
- the use of [option] types instead of [Not_found] exceptions
- the use of [nat] instead of [int] for the [cardinal] function
Several variants of the set interfaces are available:
- [WSetsOn] : functorial signature for weak sets
- [WSets] : self-contained version of [WSets]
- [SetsOn] : functorial signature for ordered sets
- [Sets] : self-contained version of [Sets]
- [WRawSets] : a signature for weak sets that may be ill-formed
- [RawSets] : same for ordered sets
If unsure, [S = Sets] is probably what you're looking for: most other
signatures are subsets of it, while [Sets] can be obtained from
[RawSets] via the use of a subset type (see (W)Raw2Sets below).
*)
Require Export Bool SetoidList RelationClasses Morphisms
RelationPairs Equalities Orders OrdersFacts.
Set Implicit Arguments.
Unset Strict Implicit.
Module Type TypElt.
Parameters t elt : Type.
End TypElt.
Module Type HasWOps (Import T:TypElt).
Parameter empty : t.
(** The empty set. *)
Parameter is_empty : t -> bool.
(** Test whether a set is empty or not. *)
Parameter mem : elt -> t -> bool.
(** [mem x s] tests whether [x] belongs to the set [s]. *)
Parameter add : elt -> t -> t.
(** [add x s] returns a set containing all elements of [s],
plus [x]. If [x] was already in [s], [s] is returned unchanged. *)
Parameter singleton : elt -> t.
(** [singleton x] returns the one-element set containing only [x]. *)
Parameter remove : elt -> t -> t.
(** [remove x s] returns a set containing all elements of [s],
except [x]. If [x] was not in [s], [s] is returned unchanged. *)
Parameter union : t -> t -> t.
(** Set union. *)
Parameter inter : t -> t -> t.
(** Set intersection. *)
Parameter diff : t -> t -> t.
(** Set difference. *)
Parameter equal : t -> t -> bool.
(** [equal s1 s2] tests whether the sets [s1] and [s2] are
equal, that is, contain equal elements. *)
Parameter subset : t -> t -> bool.
(** [subset s1 s2] tests whether the set [s1] is a subset of
the set [s2]. *)
Parameter fold : forall A : Type, (elt -> A -> A) -> t -> A -> A.
(** [fold f s a] computes [(f xN ... (f x2 (f x1 a))...)],
where [x1 ... xN] are the elements of [s].
The order in which elements of [s] are presented to [f] is
unspecified. *)
Parameter for_all : (elt -> bool) -> t -> bool.
(** [for_all p s] checks if all elements of the set
satisfy the predicate [p]. *)
Parameter exists_ : (elt -> bool) -> t -> bool.
(** [exists p s] checks if at least one element of
the set satisfies the predicate [p]. *)
Parameter filter : (elt -> bool) -> t -> t.
(** [filter p s] returns the set of all elements in [s]
that satisfy predicate [p]. *)
Parameter partition : (elt -> bool) -> t -> t * t.
(** [partition p s] returns a pair of sets [(s1, s2)], where
[s1] is the set of all the elements of [s] that satisfy the
predicate [p], and [s2] is the set of all the elements of
[s] that do not satisfy [p]. *)
Parameter cardinal : t -> nat.
(** Return the number of elements of a set. *)
Parameter elements : t -> list elt.
(** Return the list of all elements of the given set, in any order. *)
Parameter choose : t -> option elt.
(** Return one element of the given set, or [None] if
the set is empty. Which element is chosen is unspecified.
Equal sets could return different elements. *)
End HasWOps.
Module Type WOps (E : DecidableType).
Definition elt := E.t.
Parameter t : Type. (** the abstract type of sets *)
Include HasWOps.
End WOps.
(** ** Functorial signature for weak sets
Weak sets are sets without ordering on base elements, only
a decidable equality. *)
Module Type WSetsOn (E : DecidableType).
(** First, we ask for all the functions *)
Include WOps E.
(** Logical predicates *)
Parameter In : elt -> t -> Prop.
Declare Instance In_compat : Proper (E.eq==>eq==>iff) In.
Definition Equal s s' := forall a : elt, In a s <-> In a s'.
Definition Subset s s' := forall a : elt, In a s -> In a s'.
Definition Empty s := forall a : elt, ~ In a s.
Definition For_all (P : elt -> Prop) s := forall x, In x s -> P x.
Definition Exists (P : elt -> Prop) s := exists x, In x s /\ P x.
Notation "s [=] t" := (Equal s t) (at level 70, no associativity).
Notation "s [<=] t" := (Subset s t) (at level 70, no associativity).
Definition eq : t -> t -> Prop := Equal.
Include IsEq. (** [eq] is obviously an equivalence, for subtyping only *)
Include HasEqDec.
(** Specifications of set operators *)
Section Spec.
Variable s s': t.
Variable x y : elt.
Variable f : elt -> bool.
Notation compatb := (Proper (E.eq==>Logic.eq)) (only parsing).
Parameter mem_spec : mem x s = true <-> In x s.
Parameter equal_spec : equal s s' = true <-> s[=]s'.
Parameter subset_spec : subset s s' = true <-> s[<=]s'.
Parameter empty_spec : Empty empty.
Parameter is_empty_spec : is_empty s = true <-> Empty s.
Parameter add_spec : In y (add x s) <-> E.eq y x \/ In y s.
Parameter remove_spec : In y (remove x s) <-> In y s /\ ~E.eq y x.
Parameter singleton_spec : In y (singleton x) <-> E.eq y x.
Parameter union_spec : In x (union s s') <-> In x s \/ In x s'.
Parameter inter_spec : In x (inter s s') <-> In x s /\ In x s'.
Parameter diff_spec : In x (diff s s') <-> In x s /\ ~In x s'.
Parameter fold_spec : forall (A : Type) (i : A) (f : elt -> A -> A),
fold f s i = fold_left (flip f) (elements s) i.
Parameter cardinal_spec : cardinal s = length (elements s).
Parameter filter_spec : compatb f ->
(In x (filter f s) <-> In x s /\ f x = true).
Parameter for_all_spec : compatb f ->
(for_all f s = true <-> For_all (fun x => f x = true) s).
Parameter exists_spec : compatb f ->
(exists_ f s = true <-> Exists (fun x => f x = true) s).
Parameter partition_spec1 : compatb f ->
fst (partition f s) [=] filter f s.
Parameter partition_spec2 : compatb f ->
snd (partition f s) [=] filter (fun x => negb (f x)) s.
Parameter elements_spec1 : InA E.eq x (elements s) <-> In x s.
(** When compared with ordered sets, here comes the only
property that is really weaker: *)
Parameter elements_spec2w : NoDupA E.eq (elements s).
Parameter choose_spec1 : choose s = Some x -> In x s.
Parameter choose_spec2 : choose s = None -> Empty s.
End Spec.
End WSetsOn.
(** ** Static signature for weak sets
Similar to the functorial signature [WSetsOn], except that the
module [E] of base elements is incorporated in the signature. *)
Module Type WSets.
Declare Module E : DecidableType.
Include WSetsOn E.
End WSets.
(** ** Functorial signature for sets on ordered elements
Based on [WSetsOn], plus ordering on sets and [min_elt] and [max_elt]
and some stronger specifications for other functions. *)
Module Type HasOrdOps (Import T:TypElt).
Parameter compare : t -> t -> comparison.
(** Total ordering between sets. Can be used as the ordering function
for doing sets of sets. *)
Parameter min_elt : t -> option elt.
(** Return the smallest element of the given set
(with respect to the [E.compare] ordering),
or [None] if the set is empty. *)
Parameter max_elt : t -> option elt.
(** Same as [min_elt], but returns the largest element of the
given set. *)
End HasOrdOps.
Module Type Ops (E : OrderedType) := WOps E <+ HasOrdOps.
Module Type SetsOn (E : OrderedType).
Include WSetsOn E <+ HasOrdOps <+ HasLt <+ IsStrOrder.
Section Spec.
Variable s s': t.
Variable x y : elt.
Parameter compare_spec : CompSpec eq lt s s' (compare s s').
(** Additional specification of [elements] *)
Parameter elements_spec2 : sort E.lt (elements s).
(** Remark: since [fold] is specified via [elements], this stronger
specification of [elements] has an indirect impact on [fold],
which can now be proved to receive elements in increasing order.
*)
Parameter min_elt_spec1 : min_elt s = Some x -> In x s.
Parameter min_elt_spec2 : min_elt s = Some x -> In y s -> ~ E.lt y x.
Parameter min_elt_spec3 : min_elt s = None -> Empty s.
Parameter max_elt_spec1 : max_elt s = Some x -> In x s.
Parameter max_elt_spec2 : max_elt s = Some x -> In y s -> ~ E.lt x y.
Parameter max_elt_spec3 : max_elt s = None -> Empty s.
(** Additional specification of [choose] *)
Parameter choose_spec3 : choose s = Some x -> choose s' = Some y ->
Equal s s' -> E.eq x y.
End Spec.
End SetsOn.
(** ** Static signature for sets on ordered elements
Similar to the functorial signature [SetsOn], except that the
module [E] of base elements is incorporated in the signature. *)
Module Type Sets.
Declare Module E : OrderedType.
Include SetsOn E.
End Sets.
Module Type S := Sets.
(** ** Some subtyping tests
<<
WSetsOn ---> WSets
| |
| |
V V
SetsOn ---> Sets
Module S_WS (M : Sets) <: WSets := M.
Module Sfun_WSfun (E:OrderedType)(M : SetsOn E) <: WSetsOn E := M.
Module S_Sfun (M : Sets) <: SetsOn M.E := M.
Module WS_WSfun (M : WSets) <: WSetsOn M.E := M.
>>
*)
(** ** Signatures for set representations with ill-formed values.
Motivation:
For many implementation of finite sets (AVL trees, sorted
lists, lists without duplicates), we use the same two-layer
approach:
- A first module deals with the datatype (eg. list or tree) without
any restriction on the values we consider. In this module (named
"Raw" in the past), some results are stated under the assumption
that some invariant (e.g. sortedness) holds for the input sets. We
also prove that this invariant is preserved by set operators.
- A second module implements the exact Sets interface by
using a subtype, for instance [{ l : list A | sorted l }].
This module is a mere wrapper around the first Raw module.
With the interfaces below, we give some respectability to
the "Raw" modules. This allows the interested users to directly
access them via the interfaces. Even better, we can build once
and for all a functor doing the transition between Raw and usual Sets.
Description:
The type [t] of sets may contain ill-formed values on which our
set operators may give wrong answers. In particular, [mem]
may not see a element in a ill-formed set (think for instance of a
unsorted list being given to an optimized [mem] that stops
its search as soon as a strictly larger element is encountered).
Unlike optimized operators, the [In] predicate is supposed to
always be correct, even on ill-formed sets. Same for [Equal] and
other logical predicates.
A predicate parameter [Ok] is used to discriminate between
well-formed and ill-formed values. Some lemmas hold only on sets
validating [Ok]. This predicate [Ok] is required to be
preserved by set operators. Moreover, a boolean function [isok]
should exist for identifying (at least some of) the well-formed sets.
*)
Module Type WRawSets (E : DecidableType).
(** First, we ask for all the functions *)
Include WOps E.
(** Is a set well-formed or ill-formed ? *)
Parameter IsOk : t -> Prop.
Class Ok (s:t) : Prop := ok : IsOk s.
(** In order to be able to validate (at least some) particular sets as
well-formed, we ask for a boolean function for (semi-)deciding
predicate [Ok]. If [Ok] isn't decidable, [isok] may be the
always-false function. *)
Parameter isok : t -> bool.
Declare Instance isok_Ok s `(isok s = true) : Ok s | 10.
(** Logical predicates *)
Parameter In : elt -> t -> Prop.
Declare Instance In_compat : Proper (E.eq==>eq==>iff) In.
Definition Equal s s' := forall a : elt, In a s <-> In a s'.
Definition Subset s s' := forall a : elt, In a s -> In a s'.
Definition Empty s := forall a : elt, ~ In a s.
Definition For_all (P : elt -> Prop) s := forall x, In x s -> P x.
Definition Exists (P : elt -> Prop) s := exists x, In x s /\ P x.
Notation "s [=] t" := (Equal s t) (at level 70, no associativity).
Notation "s [<=] t" := (Subset s t) (at level 70, no associativity).
Definition eq : t -> t -> Prop := Equal.
Declare Instance eq_equiv : Equivalence eq.
(** First, all operations are compatible with the well-formed predicate. *)
Declare Instance empty_ok : Ok empty.
Declare Instance add_ok s x `(Ok s) : Ok (add x s).
Declare Instance remove_ok s x `(Ok s) : Ok (remove x s).
Declare Instance singleton_ok x : Ok (singleton x).
Declare Instance union_ok s s' `(Ok s, Ok s') : Ok (union s s').
Declare Instance inter_ok s s' `(Ok s, Ok s') : Ok (inter s s').
Declare Instance diff_ok s s' `(Ok s, Ok s') : Ok (diff s s').
Declare Instance filter_ok s f `(Ok s) : Ok (filter f s).
Declare Instance partition_ok1 s f `(Ok s) : Ok (fst (partition f s)).
Declare Instance partition_ok2 s f `(Ok s) : Ok (snd (partition f s)).
(** Now, the specifications, with constraints on the input sets. *)
Section Spec.
Variable s s': t.
Variable x y : elt.
Variable f : elt -> bool.
Notation compatb := (Proper (E.eq==>Logic.eq)) (only parsing).
Parameter mem_spec : forall `{Ok s}, mem x s = true <-> In x s.
Parameter equal_spec : forall `{Ok s, Ok s'},
equal s s' = true <-> s[=]s'.
Parameter subset_spec : forall `{Ok s, Ok s'},
subset s s' = true <-> s[<=]s'.
Parameter empty_spec : Empty empty.
Parameter is_empty_spec : is_empty s = true <-> Empty s.
Parameter add_spec : forall `{Ok s},
In y (add x s) <-> E.eq y x \/ In y s.
Parameter remove_spec : forall `{Ok s},
In y (remove x s) <-> In y s /\ ~E.eq y x.
Parameter singleton_spec : In y (singleton x) <-> E.eq y x.
Parameter union_spec : forall `{Ok s, Ok s'},
In x (union s s') <-> In x s \/ In x s'.
Parameter inter_spec : forall `{Ok s, Ok s'},
In x (inter s s') <-> In x s /\ In x s'.
Parameter diff_spec : forall `{Ok s, Ok s'},
In x (diff s s') <-> In x s /\ ~In x s'.
Parameter fold_spec : forall (A : Type) (i : A) (f : elt -> A -> A),
fold f s i = fold_left (flip f) (elements s) i.
Parameter cardinal_spec : forall `{Ok s},
cardinal s = length (elements s).
Parameter filter_spec : compatb f ->
(In x (filter f s) <-> In x s /\ f x = true).
Parameter for_all_spec : compatb f ->
(for_all f s = true <-> For_all (fun x => f x = true) s).
Parameter exists_spec : compatb f ->
(exists_ f s = true <-> Exists (fun x => f x = true) s).
Parameter partition_spec1 : compatb f ->
fst (partition f s) [=] filter f s.
Parameter partition_spec2 : compatb f ->
snd (partition f s) [=] filter (fun x => negb (f x)) s.
Parameter elements_spec1 : InA E.eq x (elements s) <-> In x s.
Parameter elements_spec2w : forall `{Ok s}, NoDupA E.eq (elements s).
Parameter choose_spec1 : choose s = Some x -> In x s.
Parameter choose_spec2 : choose s = None -> Empty s.
End Spec.
End WRawSets.
(** From weak raw sets to weak usual sets *)
Module WRaw2SetsOn (E:DecidableType)(M:WRawSets E) <: WSetsOn E.
(** We avoid creating induction principles for the Record *)
Local Unset Elimination Schemes.
Definition elt := E.t.
Record t_ := Mkt {this :> M.t; is_ok : M.Ok this}.
Definition t := t_.
Arguments Mkt this {is_ok}.
Hint Resolve is_ok : typeclass_instances.
Definition In (x : elt)(s : t) := M.In x s.(this).
Definition Equal (s s' : t) := forall a : elt, In a s <-> In a s'.
Definition Subset (s s' : t) := forall a : elt, In a s -> In a s'.
Definition Empty (s : t) := forall a : elt, ~ In a s.
Definition For_all (P : elt -> Prop)(s : t) := forall x, In x s -> P x.
Definition Exists (P : elt -> Prop)(s : t) := exists x, In x s /\ P x.
Definition mem (x : elt)(s : t) := M.mem x s.
Definition add (x : elt)(s : t) : t := Mkt (M.add x s).
Definition remove (x : elt)(s : t) : t := Mkt (M.remove x s).
Definition singleton (x : elt) : t := Mkt (M.singleton x).
Definition union (s s' : t) : t := Mkt (M.union s s').
Definition inter (s s' : t) : t := Mkt (M.inter s s').
Definition diff (s s' : t) : t := Mkt (M.diff s s').
Definition equal (s s' : t) := M.equal s s'.
Definition subset (s s' : t) := M.subset s s'.
Definition empty : t := Mkt M.empty.
Definition is_empty (s : t) := M.is_empty s.
Definition elements (s : t) : list elt := M.elements s.
Definition choose (s : t) : option elt := M.choose s.
Definition fold (A : Type)(f : elt -> A -> A)(s : t) : A -> A := M.fold f s.
Definition cardinal (s : t) := M.cardinal s.
Definition filter (f : elt -> bool)(s : t) : t := Mkt (M.filter f s).
Definition for_all (f : elt -> bool)(s : t) := M.for_all f s.
Definition exists_ (f : elt -> bool)(s : t) := M.exists_ f s.
Definition partition (f : elt -> bool)(s : t) : t * t :=
let p := M.partition f s in (Mkt (fst p), Mkt (snd p)).
Instance In_compat : Proper (E.eq==>eq==>iff) In.
Proof. repeat red. intros; apply M.In_compat; congruence. Qed.
Definition eq : t -> t -> Prop := Equal.
Instance eq_equiv : Equivalence eq.
Proof. firstorder. Qed.
Definition eq_dec : forall (s s':t), { eq s s' }+{ ~eq s s' }.
Proof.
intros (s,Hs) (s',Hs').
change ({M.Equal s s'}+{~M.Equal s s'}).
destruct (M.equal s s') eqn:H; [left|right];
rewrite <- M.equal_spec; congruence.
Defined.
Section Spec.
Variable s s' : t.
Variable x y : elt.
Variable f : elt -> bool.
Notation compatb := (Proper (E.eq==>Logic.eq)) (only parsing).
Lemma mem_spec : mem x s = true <-> In x s.
Proof. exact (@M.mem_spec _ _ _). Qed.
Lemma equal_spec : equal s s' = true <-> Equal s s'.
Proof. exact (@M.equal_spec _ _ _ _). Qed.
Lemma subset_spec : subset s s' = true <-> Subset s s'.
Proof. exact (@M.subset_spec _ _ _ _). Qed.
Lemma empty_spec : Empty empty.
Proof. exact M.empty_spec. Qed.
Lemma is_empty_spec : is_empty s = true <-> Empty s.
Proof. exact (@M.is_empty_spec _). Qed.
Lemma add_spec : In y (add x s) <-> E.eq y x \/ In y s.
Proof. exact (@M.add_spec _ _ _ _). Qed.
Lemma remove_spec : In y (remove x s) <-> In y s /\ ~E.eq y x.
Proof. exact (@M.remove_spec _ _ _ _). Qed.
Lemma singleton_spec : In y (singleton x) <-> E.eq y x.
Proof. exact (@M.singleton_spec _ _). Qed.
Lemma union_spec : In x (union s s') <-> In x s \/ In x s'.
Proof. exact (@M.union_spec _ _ _ _ _). Qed.
Lemma inter_spec : In x (inter s s') <-> In x s /\ In x s'.
Proof. exact (@M.inter_spec _ _ _ _ _). Qed.
Lemma diff_spec : In x (diff s s') <-> In x s /\ ~In x s'.
Proof. exact (@M.diff_spec _ _ _ _ _). Qed.
Lemma fold_spec : forall (A : Type) (i : A) (f : elt -> A -> A),
fold f s i = fold_left (fun a e => f e a) (elements s) i.
Proof. exact (@M.fold_spec _). Qed.
Lemma cardinal_spec : cardinal s = length (elements s).
Proof. exact (@M.cardinal_spec s _). Qed.
Lemma filter_spec : compatb f ->
(In x (filter f s) <-> In x s /\ f x = true).
Proof. exact (@M.filter_spec _ _ _). Qed.
Lemma for_all_spec : compatb f ->
(for_all f s = true <-> For_all (fun x => f x = true) s).
Proof. exact (@M.for_all_spec _ _). Qed.
Lemma exists_spec : compatb f ->
(exists_ f s = true <-> Exists (fun x => f x = true) s).
Proof. exact (@M.exists_spec _ _). Qed.
Lemma partition_spec1 : compatb f -> Equal (fst (partition f s)) (filter f s).
Proof. exact (@M.partition_spec1 _ _). Qed.
Lemma partition_spec2 : compatb f ->
Equal (snd (partition f s)) (filter (fun x => negb (f x)) s).
Proof. exact (@M.partition_spec2 _ _). Qed.
Lemma elements_spec1 : InA E.eq x (elements s) <-> In x s.
Proof. exact (@M.elements_spec1 _ _). Qed.
Lemma elements_spec2w : NoDupA E.eq (elements s).
Proof. exact (@M.elements_spec2w _ _). Qed.
Lemma choose_spec1 : choose s = Some x -> In x s.
Proof. exact (@M.choose_spec1 _ _). Qed.
Lemma choose_spec2 : choose s = None -> Empty s.
Proof. exact (@M.choose_spec2 _). Qed.
End Spec.
End WRaw2SetsOn.
Module WRaw2Sets (D:DecidableType)(M:WRawSets D) <: WSets with Module E := D.
Module E := D.
Include WRaw2SetsOn D M.
End WRaw2Sets.
(** Same approach for ordered sets *)
Module Type RawSets (E : OrderedType).
Include WRawSets E <+ HasOrdOps <+ HasLt <+ IsStrOrder.
Section Spec.
Variable s s': t.
Variable x y : elt.
(** Specification of [compare] *)
Parameter compare_spec : forall `{Ok s, Ok s'}, CompSpec eq lt s s' (compare s s').
(** Additional specification of [elements] *)
Parameter elements_spec2 : forall `{Ok s}, sort E.lt (elements s).
(** Specification of [min_elt] *)
Parameter min_elt_spec1 : min_elt s = Some x -> In x s.
Parameter min_elt_spec2 : forall `{Ok s}, min_elt s = Some x -> In y s -> ~ E.lt y x.
Parameter min_elt_spec3 : min_elt s = None -> Empty s.
(** Specification of [max_elt] *)
Parameter max_elt_spec1 : max_elt s = Some x -> In x s.
Parameter max_elt_spec2 : forall `{Ok s}, max_elt s = Some x -> In y s -> ~ E.lt x y.
Parameter max_elt_spec3 : max_elt s = None -> Empty s.
(** Additional specification of [choose] *)
Parameter choose_spec3 : forall `{Ok s, Ok s'},
choose s = Some x -> choose s' = Some y -> Equal s s' -> E.eq x y.
End Spec.
End RawSets.
(** From Raw to usual sets *)
Module Raw2SetsOn (O:OrderedType)(M:RawSets O) <: SetsOn O.
Include WRaw2SetsOn O M.
Definition compare (s s':t) := M.compare s s'.
Definition min_elt (s:t) : option elt := M.min_elt s.
Definition max_elt (s:t) : option elt := M.max_elt s.
Definition lt (s s':t) := M.lt s s'.
(** Specification of [lt] *)
Instance lt_strorder : StrictOrder lt.
Proof. constructor ; unfold lt; red.
unfold complement. red. intros. apply (irreflexivity H).
intros. transitivity y; auto.
Qed.
Instance lt_compat : Proper (eq==>eq==>iff) lt.
Proof.
repeat red. unfold eq, lt.
intros (s1,p1) (s2,p2) E (s1',p1') (s2',p2') E'; simpl.
change (M.eq s1 s2) in E.
change (M.eq s1' s2') in E'.
rewrite E,E'; intuition.
Qed.
Section Spec.
Variable s s' s'' : t.
Variable x y : elt.
Lemma compare_spec : CompSpec eq lt s s' (compare s s').
Proof. unfold compare; destruct (@M.compare_spec s s' _ _); auto. Qed.
(** Additional specification of [elements] *)
Lemma elements_spec2 : sort O.lt (elements s).
Proof. exact (@M.elements_spec2 _ _). Qed.
(** Specification of [min_elt] *)
Lemma min_elt_spec1 : min_elt s = Some x -> In x s.
Proof. exact (@M.min_elt_spec1 _ _). Qed.
Lemma min_elt_spec2 : min_elt s = Some x -> In y s -> ~ O.lt y x.
Proof. exact (@M.min_elt_spec2 _ _ _ _). Qed.
Lemma min_elt_spec3 : min_elt s = None -> Empty s.
Proof. exact (@M.min_elt_spec3 _). Qed.
(** Specification of [max_elt] *)
Lemma max_elt_spec1 : max_elt s = Some x -> In x s.
Proof. exact (@M.max_elt_spec1 _ _). Qed.
Lemma max_elt_spec2 : max_elt s = Some x -> In y s -> ~ O.lt x y.
Proof. exact (@M.max_elt_spec2 _ _ _ _). Qed.
Lemma max_elt_spec3 : max_elt s = None -> Empty s.
Proof. exact (@M.max_elt_spec3 _). Qed.
(** Additional specification of [choose] *)
Lemma choose_spec3 :
choose s = Some x -> choose s' = Some y -> Equal s s' -> O.eq x y.
Proof. exact (@M.choose_spec3 _ _ _ _ _ _). Qed.
End Spec.
End Raw2SetsOn.
Module Raw2Sets (O:OrderedType)(M:RawSets O) <: Sets with Module E := O.
Module E := O.
Include Raw2SetsOn O M.
End Raw2Sets.
(** It is in fact possible to provide an ordering on sets with
very little information on them (more or less only the [In]
predicate). This generic build of ordering is in fact not
used for the moment, we rather use a simplier version
dedicated to sets-as-sorted-lists, see [MakeListOrdering].
*)
Module Type IN (O:OrderedType).
Parameter Inline t : Type.
Parameter Inline In : O.t -> t -> Prop.
Declare Instance In_compat : Proper (O.eq==>eq==>iff) In.
Definition Equal s s' := forall x, In x s <-> In x s'.
Definition Empty s := forall x, ~In x s.
End IN.
Module MakeSetOrdering (O:OrderedType)(Import M:IN O).
Module Import MO := OrderedTypeFacts O.
Definition eq : t -> t -> Prop := Equal.
Instance eq_equiv : Equivalence eq.
Proof. firstorder. Qed.
Instance : Proper (O.eq==>eq==>iff) In.
Proof.
intros x x' Ex s s' Es. rewrite Ex. apply Es.
Qed.
Definition Below x s := forall y, In y s -> O.lt y x.
Definition Above x s := forall y, In y s -> O.lt x y.
Definition EquivBefore x s s' :=
forall y, O.lt y x -> (In y s <-> In y s').
Definition EmptyBetween x y s :=
forall z, In z s -> O.lt z y -> O.lt z x.
Definition lt s s' := exists x, EquivBefore x s s' /\
((In x s' /\ Below x s) \/
(In x s /\ exists y, In y s' /\ O.lt x y /\ EmptyBetween x y s')).
Instance : Proper (O.eq==>eq==>eq==>iff) EquivBefore.
Proof.
unfold EquivBefore. intros x x' E s1 s1' E1 s2 s2' E2.
setoid_rewrite E; setoid_rewrite E1; setoid_rewrite E2; intuition.
Qed.
Instance : Proper (O.eq==>eq==>iff) Below.
Proof.
unfold Below. intros x x' Ex s s' Es.
setoid_rewrite Ex; setoid_rewrite Es; intuition.
Qed.
Instance : Proper (O.eq==>eq==>iff) Above.
Proof.
unfold Above. intros x x' Ex s s' Es.
setoid_rewrite Ex; setoid_rewrite Es; intuition.
Qed.
Instance : Proper (O.eq==>O.eq==>eq==>iff) EmptyBetween.
Proof.
unfold EmptyBetween. intros x x' Ex y y' Ey s s' Es.
setoid_rewrite Ex; setoid_rewrite Ey; setoid_rewrite Es; intuition.
Qed.
Instance lt_compat : Proper (eq==>eq==>iff) lt.
Proof.
unfold lt. intros s1 s1' E1 s2 s2' E2.
setoid_rewrite E1; setoid_rewrite E2; intuition.
Qed.
Instance lt_strorder : StrictOrder lt.
Proof.
split.
(* irreflexive *)
intros s (x & _ & [(IN,Em)|(IN & y & IN' & LT & Be)]).
specialize (Em x IN); order.
specialize (Be x IN LT); order.
(* transitive *)
intros s1 s2 s3 (x & EQ & [(IN,Pre)|(IN,Lex)])
(x' & EQ' & [(IN',Pre')|(IN',Lex')]).
(* 1) Pre / Pre --> Pre *)
assert (O.lt x x') by (specialize (Pre' x IN); auto).
exists x; split.
intros y Hy; rewrite <- (EQ' y); auto; order.
left; split; auto.
rewrite <- (EQ' x); auto.
(* 2) Pre / Lex *)
elim_compare x x'.
(* 2a) x=x' --> Pre *)
destruct Lex' as (y & INy & LT & Be).
exists y; split.
intros z Hz. split; intros INz.
specialize (Pre z INz). rewrite <- (EQ' z), <- (EQ z); auto; order.
specialize (Be z INz Hz). rewrite (EQ z), (EQ' z); auto; order.
left; split; auto.
intros z Hz. transitivity x; auto; order.
(* 2b) x<x' --> Pre *)
exists x; split.
intros z Hz. rewrite <- (EQ' z) by order; auto.
left; split; auto.
rewrite <- (EQ' x); auto.
(* 2c) x>x' --> Lex *)
exists x'; split.
intros z Hz. rewrite (EQ z) by order; auto.
right; split; auto.
rewrite (EQ x'); auto.
(* 3) Lex / Pre --> Lex *)
destruct Lex as (y & INy & LT & Be).
specialize (Pre' y INy).
exists x; split.
intros z Hz. rewrite <- (EQ' z) by order; auto.
right; split; auto.
exists y; repeat split; auto.
rewrite <- (EQ' y); auto.
intros z Hz LTz; apply Be; auto. rewrite (EQ' z); auto; order.
(* 4) Lex / Lex *)
elim_compare x x'.
(* 4a) x=x' --> impossible *)
destruct Lex as (y & INy & LT & Be).
setoid_replace x with x' in LT; auto.
specialize (Be x' IN' LT); order.
(* 4b) x<x' --> Lex *)
exists x; split.
intros z Hz. rewrite <- (EQ' z) by order; auto.
right; split; auto.
destruct Lex as (y & INy & LT & Be).
elim_compare y x'.
(* 4ba *)
destruct Lex' as (y' & Iny' & LT' & Be').
exists y'; repeat split; auto. order.
intros z Hz LTz. specialize (Be' z Hz LTz).
rewrite <- (EQ' z) in Hz by order.
apply Be; auto. order.
(* 4bb *)
exists y; repeat split; auto.
rewrite <- (EQ' y); auto.
intros z Hz LTz. apply Be; auto. rewrite (EQ' z); auto; order.
(* 4bc*)
assert (O.lt x' x) by auto. order.
(* 4c) x>x' --> Lex *)
exists x'; split.
intros z Hz. rewrite (EQ z) by order; auto.
right; split; auto.
rewrite (EQ x'); auto.
Qed.
Lemma lt_empty_r : forall s s', Empty s' -> ~ lt s s'.
Proof.
intros s s' Hs' (x & _ & [(IN,_)|(_ & y & IN & _)]).
elim (Hs' x IN).
elim (Hs' y IN).
Qed.
Definition Add x s s' := forall y, In y s' <-> O.eq x y \/ In y s.
Lemma lt_empty_l : forall x s1 s2 s2',
Empty s1 -> Above x s2 -> Add x s2 s2' -> lt s1 s2'.
Proof.
intros x s1 s2 s2' Em Ab Ad.
exists x; split.
intros y Hy; split; intros IN.
elim (Em y IN).
rewrite (Ad y) in IN; destruct IN as [EQ|IN]. order.
specialize (Ab y IN). order.
left; split.
rewrite (Ad x). now left.
intros y Hy. elim (Em y Hy).
Qed.
Lemma lt_add_lt : forall x1 x2 s1 s1' s2 s2',
Above x1 s1 -> Above x2 s2 -> Add x1 s1 s1' -> Add x2 s2 s2' ->
O.lt x1 x2 -> lt s1' s2'.
Proof.
intros x1 x2 s1 s1' s2 s2' Ab1 Ab2 Ad1 Ad2 LT.
exists x1; split; [ | right; split]; auto.
intros y Hy. rewrite (Ad1 y), (Ad2 y).
split; intros [U|U]; try order.
specialize (Ab1 y U). order.
specialize (Ab2 y U). order.
rewrite (Ad1 x1); auto with *.
exists x2; repeat split; auto.
rewrite (Ad2 x2); now left.
intros y. rewrite (Ad2 y). intros [U|U]. order.
specialize (Ab2 y U). order.
Qed.
Lemma lt_add_eq : forall x1 x2 s1 s1' s2 s2',
Above x1 s1 -> Above x2 s2 -> Add x1 s1 s1' -> Add x2 s2 s2' ->
O.eq x1 x2 -> lt s1 s2 -> lt s1' s2'.
Proof.
intros x1 x2 s1 s1' s2 s2' Ab1 Ab2 Ad1 Ad2 Hx (x & EQ & Disj).
assert (O.lt x1 x).
destruct Disj as [(IN,_)|(IN,_)]; auto. rewrite Hx; auto.
exists x; split.
intros z Hz. rewrite (Ad1 z), (Ad2 z).
split; intros [U|U]; try (left; order); right.
rewrite <- (EQ z); auto.
rewrite (EQ z); auto.
destruct Disj as [(IN,Em)|(IN & y & INy & LTy & Be)].
left; split; auto.
rewrite (Ad2 x); auto.
intros z. rewrite (Ad1 z); intros [U|U]; try specialize (Ab1 z U); auto; order.
right; split; auto.
rewrite (Ad1 x); auto.
exists y; repeat split; auto.
rewrite (Ad2 y); auto.
intros z. rewrite (Ad2 z). intros [U|U]; try specialize (Ab2 z U); auto; order.
Qed.
End MakeSetOrdering.
Module MakeListOrdering (O:OrderedType).
Module MO:=OrderedTypeFacts O.
Local Notation t := (list O.t).
Local Notation In := (InA O.eq).
Definition eq s s' := forall x, In x s <-> In x s'.
Instance eq_equiv : Equivalence eq := _.
Inductive lt_list : t -> t -> Prop :=
| lt_nil : forall x s, lt_list nil (x :: s)
| lt_cons_lt : forall x y s s',
O.lt x y -> lt_list (x :: s) (y :: s')
| lt_cons_eq : forall x y s s',
O.eq x y -> lt_list s s' -> lt_list (x :: s) (y :: s').
Hint Constructors lt_list.
Definition lt := lt_list.
Hint Unfold lt.
Instance lt_strorder : StrictOrder lt.
Proof.
split.
(* irreflexive *)
assert (forall s s', s=s' -> ~lt s s').
red; induction 2.
discriminate.
inversion H; subst.
apply (StrictOrder_Irreflexive y); auto.
inversion H; subst; auto.
intros s Hs; exact (H s s (eq_refl s) Hs).
(* transitive *)
intros s s' s'' H; generalize s''; clear s''; elim H.
intros x l s'' H'; inversion_clear H'; auto.
intros x x' l l' E s'' H'; inversion_clear H'; auto.
constructor 2. transitivity x'; auto.
constructor 2. rewrite <- H0; auto.
intros.
inversion_clear H3.
constructor 2. rewrite H0; auto.
constructor 3; auto. transitivity y; auto. unfold lt in *; auto.
Qed.
Instance lt_compat' :
Proper (eqlistA O.eq==>eqlistA O.eq==>iff) lt.
Proof.
apply proper_sym_impl_iff_2; auto with *.
intros s1 s1' E1 s2 s2' E2 H.
revert s1' E1 s2' E2.
induction H; intros; inversion_clear E1; inversion_clear E2.
constructor 1.
constructor 2. MO.order.
constructor 3. MO.order. unfold lt in *; auto.
Qed.
Lemma eq_cons :
forall l1 l2 x y,
O.eq x y -> eq l1 l2 -> eq (x :: l1) (y :: l2).
Proof.
unfold eq; intros l1 l2 x y Exy E12 z.
split; inversion_clear 1.
left; MO.order. right; rewrite <- E12; auto.
left; MO.order. right; rewrite E12; auto.
Qed.
Hint Resolve eq_cons.
Lemma cons_CompSpec : forall c x1 x2 l1 l2, O.eq x1 x2 ->
CompSpec eq lt l1 l2 c -> CompSpec eq lt (x1::l1) (x2::l2) c.
Proof.
destruct c; simpl; inversion_clear 2; auto with relations.
Qed.
Hint Resolve cons_CompSpec.
End MakeListOrdering.
|
// -- (c) Copyright 2010 - 2012 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// AXI data fifo module:
// 5-channel memory-mapped AXI4 interfaces.
// SRL or BRAM based FIFO on AXI W and/or R channels.
// FIFO to accommodate various data flow rates through the AXI interconnect
//
// Verilog-standard: Verilog 2001
//-----------------------------------------------------------------------------
//
// Structure:
// axi_data_fifo
// fifo_generator
//
//-----------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_data_fifo_v2_1_axi_data_fifo #
(
parameter C_FAMILY = "virtex7",
parameter integer C_AXI_PROTOCOL = 0,
parameter integer C_AXI_ID_WIDTH = 4,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_USER_SIGNALS = 0,
parameter integer C_AXI_AWUSER_WIDTH = 1,
parameter integer C_AXI_ARUSER_WIDTH = 1,
parameter integer C_AXI_WUSER_WIDTH = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1,
parameter integer C_AXI_WRITE_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_WRITE_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_WRITE_FIFO_DELAY = 0, // 0 = No, 1 = Yes
// Indicates whether AWVALID and WVALID assertion is delayed until:
// a. the corresponding WLAST is stored in the FIFO, or
// b. no WLAST is stored and the FIFO is full.
// 0 means AW channel is pass-through and
// WVALID is asserted whenever FIFO is not empty.
parameter integer C_AXI_READ_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_READ_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_READ_FIFO_DELAY = 0) // 0 = No, 1 = Yes
// Indicates whether ARVALID assertion is delayed until the
// the remaining vacancy of the FIFO is at least the burst length
// as indicated by ARLEN.
// 0 means AR channel is pass-through.
// System Signals
(input wire aclk,
input wire aresetn,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_awaddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_awlen,
input wire [3-1:0] s_axi_awsize,
input wire [2-1:0] s_axi_awburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_awlock,
input wire [4-1:0] s_axi_awcache,
input wire [3-1:0] s_axi_awprot,
input wire [4-1:0] s_axi_awregion,
input wire [4-1:0] s_axi_awqos,
input wire [C_AXI_AWUSER_WIDTH-1:0] s_axi_awuser,
input wire s_axi_awvalid,
output wire s_axi_awready,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_wid,
input wire [C_AXI_DATA_WIDTH-1:0] s_axi_wdata,
input wire [C_AXI_DATA_WIDTH/8-1:0] s_axi_wstrb,
input wire s_axi_wlast,
input wire [C_AXI_WUSER_WIDTH-1:0] s_axi_wuser,
input wire s_axi_wvalid,
output wire s_axi_wready,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output wire [2-1:0] s_axi_bresp,
output wire [C_AXI_BUSER_WIDTH-1:0] s_axi_buser,
output wire s_axi_bvalid,
input wire s_axi_bready,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_araddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_arlen,
input wire [3-1:0] s_axi_arsize,
input wire [2-1:0] s_axi_arburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_arlock,
input wire [4-1:0] s_axi_arcache,
input wire [3-1:0] s_axi_arprot,
input wire [4-1:0] s_axi_arregion,
input wire [4-1:0] s_axi_arqos,
input wire [C_AXI_ARUSER_WIDTH-1:0] s_axi_aruser,
input wire s_axi_arvalid,
output wire s_axi_arready,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output wire [C_AXI_DATA_WIDTH-1:0] s_axi_rdata,
output wire [2-1:0] s_axi_rresp,
output wire s_axi_rlast,
output wire [C_AXI_RUSER_WIDTH-1:0] s_axi_ruser,
output wire s_axi_rvalid,
input wire s_axi_rready,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_awid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_awaddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_awlen,
output wire [3-1:0] m_axi_awsize,
output wire [2-1:0] m_axi_awburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_awlock,
output wire [4-1:0] m_axi_awcache,
output wire [3-1:0] m_axi_awprot,
output wire [4-1:0] m_axi_awregion,
output wire [4-1:0] m_axi_awqos,
output wire [C_AXI_AWUSER_WIDTH-1:0] m_axi_awuser,
output wire m_axi_awvalid,
input wire m_axi_awready,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] m_axi_wid,
output wire [C_AXI_DATA_WIDTH-1:0] m_axi_wdata,
output wire [C_AXI_DATA_WIDTH/8-1:0] m_axi_wstrb,
output wire m_axi_wlast,
output wire [C_AXI_WUSER_WIDTH-1:0] m_axi_wuser,
output wire m_axi_wvalid,
input wire m_axi_wready,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_bid,
input wire [2-1:0] m_axi_bresp,
input wire [C_AXI_BUSER_WIDTH-1:0] m_axi_buser,
input wire m_axi_bvalid,
output wire m_axi_bready,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_arid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_araddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_arlen,
output wire [3-1:0] m_axi_arsize,
output wire [2-1:0] m_axi_arburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_arlock,
output wire [4-1:0] m_axi_arcache,
output wire [3-1:0] m_axi_arprot,
output wire [4-1:0] m_axi_arregion,
output wire [4-1:0] m_axi_arqos,
output wire [C_AXI_ARUSER_WIDTH-1:0] m_axi_aruser,
output wire m_axi_arvalid,
input wire m_axi_arready,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_rid,
input wire [C_AXI_DATA_WIDTH-1:0] m_axi_rdata,
input wire [2-1:0] m_axi_rresp,
input wire m_axi_rlast,
input wire [C_AXI_RUSER_WIDTH-1:0] m_axi_ruser,
input wire m_axi_rvalid,
output wire m_axi_rready);
localparam integer P_WIDTH_RACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_ARUSER_WIDTH;
localparam integer P_WIDTH_WACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_AWUSER_WIDTH;
localparam integer P_WIDTH_RDCH = 1 + 2 + C_AXI_DATA_WIDTH + C_AXI_ID_WIDTH + C_AXI_RUSER_WIDTH;
localparam integer P_WIDTH_WDCH = 1+C_AXI_DATA_WIDTH+C_AXI_DATA_WIDTH/8+((C_AXI_PROTOCOL==1)?C_AXI_ID_WIDTH:0)+C_AXI_WUSER_WIDTH;
localparam integer P_WIDTH_WRCH = 2 + C_AXI_ID_WIDTH + C_AXI_BUSER_WIDTH;
localparam P_PRIM_FIFO_TYPE = "512x72" ;
localparam integer P_AXI4 = 0;
localparam integer P_AXI3 = 1;
localparam integer P_AXILITE = 2;
localparam integer P_WRITE_FIFO_DEPTH_LOG = (C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1;
localparam integer P_READ_FIFO_DEPTH_LOG = (C_AXI_READ_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1;
// Ceiling of log2(x)
function integer f_ceil_log2
(
input integer x
);
integer acc;
begin
acc=0;
while ((2**acc) < x)
acc = acc + 1;
f_ceil_log2 = acc;
end
endfunction
generate
if (((C_AXI_WRITE_FIFO_DEPTH == 0) && (C_AXI_READ_FIFO_DEPTH == 0)) || (C_AXI_PROTOCOL == P_AXILITE)) begin : gen_bypass
assign m_axi_awid = s_axi_awid;
assign m_axi_awaddr = s_axi_awaddr;
assign m_axi_awlen = s_axi_awlen;
assign m_axi_awsize = s_axi_awsize;
assign m_axi_awburst = s_axi_awburst;
assign m_axi_awlock = s_axi_awlock;
assign m_axi_awcache = s_axi_awcache;
assign m_axi_awprot = s_axi_awprot;
assign m_axi_awregion = s_axi_awregion;
assign m_axi_awqos = s_axi_awqos;
assign m_axi_awuser = s_axi_awuser;
assign m_axi_awvalid = s_axi_awvalid;
assign s_axi_awready = m_axi_awready;
assign m_axi_wid = s_axi_wid;
assign m_axi_wdata = s_axi_wdata;
assign m_axi_wstrb = s_axi_wstrb;
assign m_axi_wlast = s_axi_wlast;
assign m_axi_wuser = s_axi_wuser;
assign m_axi_wvalid = s_axi_wvalid;
assign s_axi_wready = m_axi_wready;
assign s_axi_bid = m_axi_bid;
assign s_axi_bresp = m_axi_bresp;
assign s_axi_buser = m_axi_buser;
assign s_axi_bvalid = m_axi_bvalid;
assign m_axi_bready = s_axi_bready;
assign m_axi_arid = s_axi_arid;
assign m_axi_araddr = s_axi_araddr;
assign m_axi_arlen = s_axi_arlen;
assign m_axi_arsize = s_axi_arsize;
assign m_axi_arburst = s_axi_arburst;
assign m_axi_arlock = s_axi_arlock;
assign m_axi_arcache = s_axi_arcache;
assign m_axi_arprot = s_axi_arprot;
assign m_axi_arregion = s_axi_arregion;
assign m_axi_arqos = s_axi_arqos;
assign m_axi_aruser = s_axi_aruser;
assign m_axi_arvalid = s_axi_arvalid;
assign s_axi_arready = m_axi_arready;
assign s_axi_rid = m_axi_rid;
assign s_axi_rdata = m_axi_rdata;
assign s_axi_rresp = m_axi_rresp;
assign s_axi_rlast = m_axi_rlast;
assign s_axi_ruser = m_axi_ruser;
assign s_axi_rvalid = m_axi_rvalid;
assign m_axi_rready = s_axi_rready;
end else begin : gen_fifo
wire [4-1:0] s_axi_awregion_i;
wire [4-1:0] s_axi_arregion_i;
wire [4-1:0] m_axi_awregion_i;
wire [4-1:0] m_axi_arregion_i;
wire [C_AXI_ID_WIDTH-1:0] s_axi_wid_i;
wire [C_AXI_ID_WIDTH-1:0] m_axi_wid_i;
assign s_axi_awregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_awregion;
assign s_axi_arregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_arregion;
assign m_axi_awregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_awregion_i;
assign m_axi_arregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_arregion_i;
assign s_axi_wid_i = (C_AXI_PROTOCOL == P_AXI3) ? s_axi_wid : {C_AXI_ID_WIDTH{1'b0}};
assign m_axi_wid = (C_AXI_PROTOCOL == P_AXI3) ? m_axi_wid_i : {C_AXI_ID_WIDTH{1'b0}};
fifo_generator_v12_0 #(
.C_INTERFACE_TYPE(2),
.C_AXI_TYPE((C_AXI_PROTOCOL == P_AXI4) ? 1 : 3),
.C_AXI_DATA_WIDTH(C_AXI_DATA_WIDTH),
.C_AXI_ID_WIDTH(C_AXI_ID_WIDTH),
.C_HAS_AXI_ID(1),
.C_AXI_LEN_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 8 : 4),
.C_AXI_LOCK_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 1 : 2),
.C_HAS_AXI_ARUSER(1),
.C_HAS_AXI_AWUSER(1),
.C_HAS_AXI_BUSER(1),
.C_HAS_AXI_RUSER(1),
.C_HAS_AXI_WUSER(1),
.C_AXI_ADDR_WIDTH(C_AXI_ADDR_WIDTH),
.C_AXI_ARUSER_WIDTH(C_AXI_ARUSER_WIDTH),
.C_AXI_AWUSER_WIDTH(C_AXI_AWUSER_WIDTH),
.C_AXI_BUSER_WIDTH(C_AXI_BUSER_WIDTH),
.C_AXI_RUSER_WIDTH(C_AXI_RUSER_WIDTH),
.C_AXI_WUSER_WIDTH(C_AXI_WUSER_WIDTH),
.C_DIN_WIDTH_RACH(P_WIDTH_RACH),
.C_DIN_WIDTH_RDCH(P_WIDTH_RDCH),
.C_DIN_WIDTH_WACH(P_WIDTH_WACH),
.C_DIN_WIDTH_WDCH(P_WIDTH_WDCH),
.C_DIN_WIDTH_WRCH(P_WIDTH_WDCH),
.C_RACH_TYPE(((C_AXI_READ_FIFO_DEPTH != 0) && C_AXI_READ_FIFO_DELAY) ? 0 : 2),
.C_WACH_TYPE(((C_AXI_WRITE_FIFO_DEPTH != 0) && C_AXI_WRITE_FIFO_DELAY) ? 0 : 2),
.C_WDCH_TYPE((C_AXI_WRITE_FIFO_DEPTH != 0) ? 0 : 2),
.C_RDCH_TYPE((C_AXI_READ_FIFO_DEPTH != 0) ? 0 : 2),
.C_WRCH_TYPE(2),
.C_COMMON_CLOCK(1),
.C_ADD_NGC_CONSTRAINT(0),
.C_APPLICATION_TYPE_AXIS(0),
.C_APPLICATION_TYPE_RACH(C_AXI_READ_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_RDCH(0),
.C_APPLICATION_TYPE_WACH(C_AXI_WRITE_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_WDCH(0),
.C_APPLICATION_TYPE_WRCH(0),
.C_AXIS_TDATA_WIDTH(64),
.C_AXIS_TDEST_WIDTH(4),
.C_AXIS_TID_WIDTH(8),
.C_AXIS_TKEEP_WIDTH(4),
.C_AXIS_TSTRB_WIDTH(4),
.C_AXIS_TUSER_WIDTH(4),
.C_AXIS_TYPE(0),
.C_COUNT_TYPE(0),
.C_DATA_COUNT_WIDTH(10),
.C_DEFAULT_VALUE("BlankString"),
.C_DIN_WIDTH(18),
.C_DIN_WIDTH_AXIS(1),
.C_DOUT_RST_VAL("0"),
.C_DOUT_WIDTH(18),
.C_ENABLE_RLOCS(0),
.C_ENABLE_RST_SYNC(1),
.C_ERROR_INJECTION_TYPE(0),
.C_ERROR_INJECTION_TYPE_AXIS(0),
.C_ERROR_INJECTION_TYPE_RACH(0),
.C_ERROR_INJECTION_TYPE_RDCH(0),
.C_ERROR_INJECTION_TYPE_WACH(0),
.C_ERROR_INJECTION_TYPE_WDCH(0),
.C_ERROR_INJECTION_TYPE_WRCH(0),
.C_FAMILY(C_FAMILY),
.C_FULL_FLAGS_RST_VAL(1),
.C_HAS_ALMOST_EMPTY(0),
.C_HAS_ALMOST_FULL(0),
.C_HAS_AXI_RD_CHANNEL(1),
.C_HAS_AXI_WR_CHANNEL(1),
.C_HAS_AXIS_TDATA(0),
.C_HAS_AXIS_TDEST(0),
.C_HAS_AXIS_TID(0),
.C_HAS_AXIS_TKEEP(0),
.C_HAS_AXIS_TLAST(0),
.C_HAS_AXIS_TREADY(1),
.C_HAS_AXIS_TSTRB(0),
.C_HAS_AXIS_TUSER(0),
.C_HAS_BACKUP(0),
.C_HAS_DATA_COUNT(0),
.C_HAS_DATA_COUNTS_AXIS(0),
.C_HAS_DATA_COUNTS_RACH(0),
.C_HAS_DATA_COUNTS_RDCH(0),
.C_HAS_DATA_COUNTS_WACH(0),
.C_HAS_DATA_COUNTS_WDCH(0),
.C_HAS_DATA_COUNTS_WRCH(0),
.C_HAS_INT_CLK(0),
.C_HAS_MASTER_CE(0),
.C_HAS_MEMINIT_FILE(0),
.C_HAS_OVERFLOW(0),
.C_HAS_PROG_FLAGS_AXIS(0),
.C_HAS_PROG_FLAGS_RACH(0),
.C_HAS_PROG_FLAGS_RDCH(0),
.C_HAS_PROG_FLAGS_WACH(0),
.C_HAS_PROG_FLAGS_WDCH(0),
.C_HAS_PROG_FLAGS_WRCH(0),
.C_HAS_RD_DATA_COUNT(0),
.C_HAS_RD_RST(0),
.C_HAS_RST(1),
.C_HAS_SLAVE_CE(0),
.C_HAS_SRST(0),
.C_HAS_UNDERFLOW(0),
.C_HAS_VALID(0),
.C_HAS_WR_ACK(0),
.C_HAS_WR_DATA_COUNT(0),
.C_HAS_WR_RST(0),
.C_IMPLEMENTATION_TYPE(0),
.C_IMPLEMENTATION_TYPE_AXIS(1),
.C_IMPLEMENTATION_TYPE_RACH(2),
.C_IMPLEMENTATION_TYPE_RDCH((C_AXI_READ_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WACH(2),
.C_IMPLEMENTATION_TYPE_WDCH((C_AXI_WRITE_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WRCH(2),
.C_INIT_WR_PNTR_VAL(0),
.C_MEMORY_TYPE(1),
.C_MIF_FILE_NAME("BlankString"),
.C_MSGON_VAL(1),
.C_OPTIMIZATION_MODE(0),
.C_OVERFLOW_LOW(0),
.C_PRELOAD_LATENCY(1),
.C_PRELOAD_REGS(0),
.C_PRIM_FIFO_TYPE(P_PRIM_FIFO_TYPE),
.C_PROG_EMPTY_THRESH_ASSERT_VAL(2),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_AXIS(1022),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WRCH(14),
.C_PROG_EMPTY_THRESH_NEGATE_VAL(3),
.C_PROG_EMPTY_TYPE(0),
.C_PROG_EMPTY_TYPE_AXIS(5),
.C_PROG_EMPTY_TYPE_RACH(5),
.C_PROG_EMPTY_TYPE_RDCH(5),
.C_PROG_EMPTY_TYPE_WACH(5),
.C_PROG_EMPTY_TYPE_WDCH(5),
.C_PROG_EMPTY_TYPE_WRCH(5),
.C_PROG_FULL_THRESH_ASSERT_VAL(1022),
.C_PROG_FULL_THRESH_ASSERT_VAL_AXIS(1023),
.C_PROG_FULL_THRESH_ASSERT_VAL_RACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_RDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_WDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WRCH(15),
.C_PROG_FULL_THRESH_NEGATE_VAL(1021),
.C_PROG_FULL_TYPE(0),
.C_PROG_FULL_TYPE_AXIS(5),
.C_PROG_FULL_TYPE_RACH(5),
.C_PROG_FULL_TYPE_RDCH(5),
.C_PROG_FULL_TYPE_WACH(5),
.C_PROG_FULL_TYPE_WDCH(5),
.C_PROG_FULL_TYPE_WRCH(5),
.C_RD_DATA_COUNT_WIDTH(10),
.C_RD_DEPTH(1024),
.C_RD_FREQ(1),
.C_RD_PNTR_WIDTH(10),
.C_REG_SLICE_MODE_AXIS(0),
.C_REG_SLICE_MODE_RACH(0),
.C_REG_SLICE_MODE_RDCH(0),
.C_REG_SLICE_MODE_WACH(0),
.C_REG_SLICE_MODE_WDCH(0),
.C_REG_SLICE_MODE_WRCH(0),
.C_UNDERFLOW_LOW(0),
.C_USE_COMMON_OVERFLOW(0),
.C_USE_COMMON_UNDERFLOW(0),
.C_USE_DEFAULT_SETTINGS(0),
.C_USE_DOUT_RST(1),
.C_USE_ECC(0),
.C_USE_ECC_AXIS(0),
.C_USE_ECC_RACH(0),
.C_USE_ECC_RDCH(0),
.C_USE_ECC_WACH(0),
.C_USE_ECC_WDCH(0),
.C_USE_ECC_WRCH(0),
.C_USE_EMBEDDED_REG(0),
.C_USE_FIFO16_FLAGS(0),
.C_USE_FWFT_DATA_COUNT(0),
.C_VALID_LOW(0),
.C_WR_ACK_LOW(0),
.C_WR_DATA_COUNT_WIDTH(10),
.C_WR_DEPTH(1024),
.C_WR_DEPTH_AXIS(1024),
.C_WR_DEPTH_RACH(32),
.C_WR_DEPTH_RDCH(C_AXI_READ_FIFO_DEPTH),
.C_WR_DEPTH_WACH(32),
.C_WR_DEPTH_WDCH(C_AXI_WRITE_FIFO_DEPTH),
.C_WR_DEPTH_WRCH(16),
.C_WR_FREQ(1),
.C_WR_PNTR_WIDTH(10),
.C_WR_PNTR_WIDTH_AXIS(10),
.C_WR_PNTR_WIDTH_RACH(5),
.C_WR_PNTR_WIDTH_RDCH((C_AXI_READ_FIFO_DEPTH> 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WACH(5),
.C_WR_PNTR_WIDTH_WDCH((C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WRCH(4),
.C_WR_RESPONSE_LATENCY(1)
)
fifo_gen_inst (
.s_aclk(aclk),
.s_aresetn(aresetn),
.s_axi_awid(s_axi_awid),
.s_axi_awaddr(s_axi_awaddr),
.s_axi_awlen(s_axi_awlen),
.s_axi_awsize(s_axi_awsize),
.s_axi_awburst(s_axi_awburst),
.s_axi_awlock(s_axi_awlock),
.s_axi_awcache(s_axi_awcache),
.s_axi_awprot(s_axi_awprot),
.s_axi_awqos(s_axi_awqos),
.s_axi_awregion(s_axi_awregion_i),
.s_axi_awuser(s_axi_awuser),
.s_axi_awvalid(s_axi_awvalid),
.s_axi_awready(s_axi_awready),
.s_axi_wid(s_axi_wid_i),
.s_axi_wdata(s_axi_wdata),
.s_axi_wstrb(s_axi_wstrb),
.s_axi_wlast(s_axi_wlast),
.s_axi_wvalid(s_axi_wvalid),
.s_axi_wready(s_axi_wready),
.s_axi_bid(s_axi_bid),
.s_axi_bresp(s_axi_bresp),
.s_axi_bvalid(s_axi_bvalid),
.s_axi_bready(s_axi_bready),
.m_axi_awid(m_axi_awid),
.m_axi_awaddr(m_axi_awaddr),
.m_axi_awlen(m_axi_awlen),
.m_axi_awsize(m_axi_awsize),
.m_axi_awburst(m_axi_awburst),
.m_axi_awlock(m_axi_awlock),
.m_axi_awcache(m_axi_awcache),
.m_axi_awprot(m_axi_awprot),
.m_axi_awqos(m_axi_awqos),
.m_axi_awregion(m_axi_awregion_i),
.m_axi_awuser(m_axi_awuser),
.m_axi_awvalid(m_axi_awvalid),
.m_axi_awready(m_axi_awready),
.m_axi_wid(m_axi_wid_i),
.m_axi_wdata(m_axi_wdata),
.m_axi_wstrb(m_axi_wstrb),
.m_axi_wlast(m_axi_wlast),
.m_axi_wvalid(m_axi_wvalid),
.m_axi_wready(m_axi_wready),
.m_axi_bid(m_axi_bid),
.m_axi_bresp(m_axi_bresp),
.m_axi_bvalid(m_axi_bvalid),
.m_axi_bready(m_axi_bready),
.s_axi_arid(s_axi_arid),
.s_axi_araddr(s_axi_araddr),
.s_axi_arlen(s_axi_arlen),
.s_axi_arsize(s_axi_arsize),
.s_axi_arburst(s_axi_arburst),
.s_axi_arlock(s_axi_arlock),
.s_axi_arcache(s_axi_arcache),
.s_axi_arprot(s_axi_arprot),
.s_axi_arqos(s_axi_arqos),
.s_axi_arregion(s_axi_arregion_i),
.s_axi_arvalid(s_axi_arvalid),
.s_axi_arready(s_axi_arready),
.s_axi_rid(s_axi_rid),
.s_axi_rdata(s_axi_rdata),
.s_axi_rresp(s_axi_rresp),
.s_axi_rlast(s_axi_rlast),
.s_axi_rvalid(s_axi_rvalid),
.s_axi_rready(s_axi_rready),
.m_axi_arid(m_axi_arid),
.m_axi_araddr(m_axi_araddr),
.m_axi_arlen(m_axi_arlen),
.m_axi_arsize(m_axi_arsize),
.m_axi_arburst(m_axi_arburst),
.m_axi_arlock(m_axi_arlock),
.m_axi_arcache(m_axi_arcache),
.m_axi_arprot(m_axi_arprot),
.m_axi_arqos(m_axi_arqos),
.m_axi_arregion(m_axi_arregion_i),
.m_axi_arvalid(m_axi_arvalid),
.m_axi_arready(m_axi_arready),
.m_axi_rid(m_axi_rid),
.m_axi_rdata(m_axi_rdata),
.m_axi_rresp(m_axi_rresp),
.m_axi_rlast(m_axi_rlast),
.m_axi_rvalid(m_axi_rvalid),
.m_axi_rready(m_axi_rready),
.m_aclk(aclk),
.m_aclk_en(1'b1),
.s_aclk_en(1'b1),
.s_axi_wuser(s_axi_wuser),
.s_axi_buser(s_axi_buser),
.m_axi_wuser(m_axi_wuser),
.m_axi_buser(m_axi_buser),
.s_axi_aruser(s_axi_aruser),
.s_axi_ruser(s_axi_ruser),
.m_axi_aruser(m_axi_aruser),
.m_axi_ruser(m_axi_ruser),
.almost_empty(),
.almost_full(),
.axis_data_count(),
.axis_dbiterr(),
.axis_injectdbiterr(1'b0),
.axis_injectsbiterr(1'b0),
.axis_overflow(),
.axis_prog_empty(),
.axis_prog_empty_thresh(10'b0),
.axis_prog_full(),
.axis_prog_full_thresh(10'b0),
.axis_rd_data_count(),
.axis_sbiterr(),
.axis_underflow(),
.axis_wr_data_count(),
.axi_ar_data_count(),
.axi_ar_dbiterr(),
.axi_ar_injectdbiterr(1'b0),
.axi_ar_injectsbiterr(1'b0),
.axi_ar_overflow(),
.axi_ar_prog_empty(),
.axi_ar_prog_empty_thresh(5'b0),
.axi_ar_prog_full(),
.axi_ar_prog_full_thresh(5'b0),
.axi_ar_rd_data_count(),
.axi_ar_sbiterr(),
.axi_ar_underflow(),
.axi_ar_wr_data_count(),
.axi_aw_data_count(),
.axi_aw_dbiterr(),
.axi_aw_injectdbiterr(1'b0),
.axi_aw_injectsbiterr(1'b0),
.axi_aw_overflow(),
.axi_aw_prog_empty(),
.axi_aw_prog_empty_thresh(5'b0),
.axi_aw_prog_full(),
.axi_aw_prog_full_thresh(5'b0),
.axi_aw_rd_data_count(),
.axi_aw_sbiterr(),
.axi_aw_underflow(),
.axi_aw_wr_data_count(),
.axi_b_data_count(),
.axi_b_dbiterr(),
.axi_b_injectdbiterr(1'b0),
.axi_b_injectsbiterr(1'b0),
.axi_b_overflow(),
.axi_b_prog_empty(),
.axi_b_prog_empty_thresh(4'b0),
.axi_b_prog_full(),
.axi_b_prog_full_thresh(4'b0),
.axi_b_rd_data_count(),
.axi_b_sbiterr(),
.axi_b_underflow(),
.axi_b_wr_data_count(),
.axi_r_data_count(),
.axi_r_dbiterr(),
.axi_r_injectdbiterr(1'b0),
.axi_r_injectsbiterr(1'b0),
.axi_r_overflow(),
.axi_r_prog_empty(),
.axi_r_prog_empty_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_prog_full(),
.axi_r_prog_full_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_rd_data_count(),
.axi_r_sbiterr(),
.axi_r_underflow(),
.axi_r_wr_data_count(),
.axi_w_data_count(),
.axi_w_dbiterr(),
.axi_w_injectdbiterr(1'b0),
.axi_w_injectsbiterr(1'b0),
.axi_w_overflow(),
.axi_w_prog_empty(),
.axi_w_prog_empty_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_prog_full(),
.axi_w_prog_full_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_rd_data_count(),
.axi_w_sbiterr(),
.axi_w_underflow(),
.axi_w_wr_data_count(),
.backup(1'b0),
.backup_marker(1'b0),
.clk(1'b0),
.data_count(),
.dbiterr(),
.din(18'b0),
.dout(),
.empty(),
.full(),
.injectdbiterr(1'b0),
.injectsbiterr(1'b0),
.int_clk(1'b0),
.m_axis_tdata(),
.m_axis_tdest(),
.m_axis_tid(),
.m_axis_tkeep(),
.m_axis_tlast(),
.m_axis_tready(1'b0),
.m_axis_tstrb(),
.m_axis_tuser(),
.m_axis_tvalid(),
.overflow(),
.prog_empty(),
.prog_empty_thresh(10'b0),
.prog_empty_thresh_assert(10'b0),
.prog_empty_thresh_negate(10'b0),
.prog_full(),
.prog_full_thresh(10'b0),
.prog_full_thresh_assert(10'b0),
.prog_full_thresh_negate(10'b0),
.rd_clk(1'b0),
.rd_data_count(),
.rd_en(1'b0),
.rd_rst(1'b0),
.rst(1'b0),
.sbiterr(),
.srst(1'b0),
.s_axis_tdata(64'b0),
.s_axis_tdest(4'b0),
.s_axis_tid(8'b0),
.s_axis_tkeep(4'b0),
.s_axis_tlast(1'b0),
.s_axis_tready(),
.s_axis_tstrb(4'b0),
.s_axis_tuser(4'b0),
.s_axis_tvalid(1'b0),
.underflow(),
.valid(),
.wr_ack(),
.wr_clk(1'b0),
.wr_data_count(),
.wr_en(1'b0),
.wr_rst(1'b0),
.wr_rst_busy(),
.rd_rst_busy(),
.sleep(1'b0)
);
end
endgenerate
endmodule
|
// -- (c) Copyright 2010 - 2012 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// AXI data fifo module:
// 5-channel memory-mapped AXI4 interfaces.
// SRL or BRAM based FIFO on AXI W and/or R channels.
// FIFO to accommodate various data flow rates through the AXI interconnect
//
// Verilog-standard: Verilog 2001
//-----------------------------------------------------------------------------
//
// Structure:
// axi_data_fifo
// fifo_generator
//
//-----------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_data_fifo_v2_1_axi_data_fifo #
(
parameter C_FAMILY = "virtex7",
parameter integer C_AXI_PROTOCOL = 0,
parameter integer C_AXI_ID_WIDTH = 4,
parameter integer C_AXI_ADDR_WIDTH = 32,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_USER_SIGNALS = 0,
parameter integer C_AXI_AWUSER_WIDTH = 1,
parameter integer C_AXI_ARUSER_WIDTH = 1,
parameter integer C_AXI_WUSER_WIDTH = 1,
parameter integer C_AXI_RUSER_WIDTH = 1,
parameter integer C_AXI_BUSER_WIDTH = 1,
parameter integer C_AXI_WRITE_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_WRITE_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_WRITE_FIFO_DELAY = 0, // 0 = No, 1 = Yes
// Indicates whether AWVALID and WVALID assertion is delayed until:
// a. the corresponding WLAST is stored in the FIFO, or
// b. no WLAST is stored and the FIFO is full.
// 0 means AW channel is pass-through and
// WVALID is asserted whenever FIFO is not empty.
parameter integer C_AXI_READ_FIFO_DEPTH = 0, // Range: (0, 32, 512)
parameter C_AXI_READ_FIFO_TYPE = "lut", // "lut" = LUT (SRL) based,
// "bram" = BRAM based
parameter integer C_AXI_READ_FIFO_DELAY = 0) // 0 = No, 1 = Yes
// Indicates whether ARVALID assertion is delayed until the
// the remaining vacancy of the FIFO is at least the burst length
// as indicated by ARLEN.
// 0 means AR channel is pass-through.
// System Signals
(input wire aclk,
input wire aresetn,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_awaddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_awlen,
input wire [3-1:0] s_axi_awsize,
input wire [2-1:0] s_axi_awburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_awlock,
input wire [4-1:0] s_axi_awcache,
input wire [3-1:0] s_axi_awprot,
input wire [4-1:0] s_axi_awregion,
input wire [4-1:0] s_axi_awqos,
input wire [C_AXI_AWUSER_WIDTH-1:0] s_axi_awuser,
input wire s_axi_awvalid,
output wire s_axi_awready,
// Slave Interface Write Data Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_wid,
input wire [C_AXI_DATA_WIDTH-1:0] s_axi_wdata,
input wire [C_AXI_DATA_WIDTH/8-1:0] s_axi_wstrb,
input wire s_axi_wlast,
input wire [C_AXI_WUSER_WIDTH-1:0] s_axi_wuser,
input wire s_axi_wvalid,
output wire s_axi_wready,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output wire [2-1:0] s_axi_bresp,
output wire [C_AXI_BUSER_WIDTH-1:0] s_axi_buser,
output wire s_axi_bvalid,
input wire s_axi_bready,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_araddr,
input wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_arlen,
input wire [3-1:0] s_axi_arsize,
input wire [2-1:0] s_axi_arburst,
input wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] s_axi_arlock,
input wire [4-1:0] s_axi_arcache,
input wire [3-1:0] s_axi_arprot,
input wire [4-1:0] s_axi_arregion,
input wire [4-1:0] s_axi_arqos,
input wire [C_AXI_ARUSER_WIDTH-1:0] s_axi_aruser,
input wire s_axi_arvalid,
output wire s_axi_arready,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output wire [C_AXI_DATA_WIDTH-1:0] s_axi_rdata,
output wire [2-1:0] s_axi_rresp,
output wire s_axi_rlast,
output wire [C_AXI_RUSER_WIDTH-1:0] s_axi_ruser,
output wire s_axi_rvalid,
input wire s_axi_rready,
// Master Interface Write Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_awid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_awaddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_awlen,
output wire [3-1:0] m_axi_awsize,
output wire [2-1:0] m_axi_awburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_awlock,
output wire [4-1:0] m_axi_awcache,
output wire [3-1:0] m_axi_awprot,
output wire [4-1:0] m_axi_awregion,
output wire [4-1:0] m_axi_awqos,
output wire [C_AXI_AWUSER_WIDTH-1:0] m_axi_awuser,
output wire m_axi_awvalid,
input wire m_axi_awready,
// Master Interface Write Data Ports
output wire [C_AXI_ID_WIDTH-1:0] m_axi_wid,
output wire [C_AXI_DATA_WIDTH-1:0] m_axi_wdata,
output wire [C_AXI_DATA_WIDTH/8-1:0] m_axi_wstrb,
output wire m_axi_wlast,
output wire [C_AXI_WUSER_WIDTH-1:0] m_axi_wuser,
output wire m_axi_wvalid,
input wire m_axi_wready,
// Master Interface Write Response Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_bid,
input wire [2-1:0] m_axi_bresp,
input wire [C_AXI_BUSER_WIDTH-1:0] m_axi_buser,
input wire m_axi_bvalid,
output wire m_axi_bready,
// Master Interface Read Address Port
output wire [C_AXI_ID_WIDTH-1:0] m_axi_arid,
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_araddr,
output wire [((C_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] m_axi_arlen,
output wire [3-1:0] m_axi_arsize,
output wire [2-1:0] m_axi_arburst,
output wire [((C_AXI_PROTOCOL == 1) ? 2 : 1)-1:0] m_axi_arlock,
output wire [4-1:0] m_axi_arcache,
output wire [3-1:0] m_axi_arprot,
output wire [4-1:0] m_axi_arregion,
output wire [4-1:0] m_axi_arqos,
output wire [C_AXI_ARUSER_WIDTH-1:0] m_axi_aruser,
output wire m_axi_arvalid,
input wire m_axi_arready,
// Master Interface Read Data Ports
input wire [C_AXI_ID_WIDTH-1:0] m_axi_rid,
input wire [C_AXI_DATA_WIDTH-1:0] m_axi_rdata,
input wire [2-1:0] m_axi_rresp,
input wire m_axi_rlast,
input wire [C_AXI_RUSER_WIDTH-1:0] m_axi_ruser,
input wire m_axi_rvalid,
output wire m_axi_rready);
localparam integer P_WIDTH_RACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_ARUSER_WIDTH;
localparam integer P_WIDTH_WACH = 4+4+3+4+2+3+((C_AXI_PROTOCOL==1)?6:9)+C_AXI_ADDR_WIDTH+C_AXI_ID_WIDTH+C_AXI_AWUSER_WIDTH;
localparam integer P_WIDTH_RDCH = 1 + 2 + C_AXI_DATA_WIDTH + C_AXI_ID_WIDTH + C_AXI_RUSER_WIDTH;
localparam integer P_WIDTH_WDCH = 1+C_AXI_DATA_WIDTH+C_AXI_DATA_WIDTH/8+((C_AXI_PROTOCOL==1)?C_AXI_ID_WIDTH:0)+C_AXI_WUSER_WIDTH;
localparam integer P_WIDTH_WRCH = 2 + C_AXI_ID_WIDTH + C_AXI_BUSER_WIDTH;
localparam P_PRIM_FIFO_TYPE = "512x72" ;
localparam integer P_AXI4 = 0;
localparam integer P_AXI3 = 1;
localparam integer P_AXILITE = 2;
localparam integer P_WRITE_FIFO_DEPTH_LOG = (C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1;
localparam integer P_READ_FIFO_DEPTH_LOG = (C_AXI_READ_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1;
// Ceiling of log2(x)
function integer f_ceil_log2
(
input integer x
);
integer acc;
begin
acc=0;
while ((2**acc) < x)
acc = acc + 1;
f_ceil_log2 = acc;
end
endfunction
generate
if (((C_AXI_WRITE_FIFO_DEPTH == 0) && (C_AXI_READ_FIFO_DEPTH == 0)) || (C_AXI_PROTOCOL == P_AXILITE)) begin : gen_bypass
assign m_axi_awid = s_axi_awid;
assign m_axi_awaddr = s_axi_awaddr;
assign m_axi_awlen = s_axi_awlen;
assign m_axi_awsize = s_axi_awsize;
assign m_axi_awburst = s_axi_awburst;
assign m_axi_awlock = s_axi_awlock;
assign m_axi_awcache = s_axi_awcache;
assign m_axi_awprot = s_axi_awprot;
assign m_axi_awregion = s_axi_awregion;
assign m_axi_awqos = s_axi_awqos;
assign m_axi_awuser = s_axi_awuser;
assign m_axi_awvalid = s_axi_awvalid;
assign s_axi_awready = m_axi_awready;
assign m_axi_wid = s_axi_wid;
assign m_axi_wdata = s_axi_wdata;
assign m_axi_wstrb = s_axi_wstrb;
assign m_axi_wlast = s_axi_wlast;
assign m_axi_wuser = s_axi_wuser;
assign m_axi_wvalid = s_axi_wvalid;
assign s_axi_wready = m_axi_wready;
assign s_axi_bid = m_axi_bid;
assign s_axi_bresp = m_axi_bresp;
assign s_axi_buser = m_axi_buser;
assign s_axi_bvalid = m_axi_bvalid;
assign m_axi_bready = s_axi_bready;
assign m_axi_arid = s_axi_arid;
assign m_axi_araddr = s_axi_araddr;
assign m_axi_arlen = s_axi_arlen;
assign m_axi_arsize = s_axi_arsize;
assign m_axi_arburst = s_axi_arburst;
assign m_axi_arlock = s_axi_arlock;
assign m_axi_arcache = s_axi_arcache;
assign m_axi_arprot = s_axi_arprot;
assign m_axi_arregion = s_axi_arregion;
assign m_axi_arqos = s_axi_arqos;
assign m_axi_aruser = s_axi_aruser;
assign m_axi_arvalid = s_axi_arvalid;
assign s_axi_arready = m_axi_arready;
assign s_axi_rid = m_axi_rid;
assign s_axi_rdata = m_axi_rdata;
assign s_axi_rresp = m_axi_rresp;
assign s_axi_rlast = m_axi_rlast;
assign s_axi_ruser = m_axi_ruser;
assign s_axi_rvalid = m_axi_rvalid;
assign m_axi_rready = s_axi_rready;
end else begin : gen_fifo
wire [4-1:0] s_axi_awregion_i;
wire [4-1:0] s_axi_arregion_i;
wire [4-1:0] m_axi_awregion_i;
wire [4-1:0] m_axi_arregion_i;
wire [C_AXI_ID_WIDTH-1:0] s_axi_wid_i;
wire [C_AXI_ID_WIDTH-1:0] m_axi_wid_i;
assign s_axi_awregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_awregion;
assign s_axi_arregion_i = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : s_axi_arregion;
assign m_axi_awregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_awregion_i;
assign m_axi_arregion = (C_AXI_PROTOCOL == P_AXI3) ? 4'b0 : m_axi_arregion_i;
assign s_axi_wid_i = (C_AXI_PROTOCOL == P_AXI3) ? s_axi_wid : {C_AXI_ID_WIDTH{1'b0}};
assign m_axi_wid = (C_AXI_PROTOCOL == P_AXI3) ? m_axi_wid_i : {C_AXI_ID_WIDTH{1'b0}};
fifo_generator_v12_0 #(
.C_INTERFACE_TYPE(2),
.C_AXI_TYPE((C_AXI_PROTOCOL == P_AXI4) ? 1 : 3),
.C_AXI_DATA_WIDTH(C_AXI_DATA_WIDTH),
.C_AXI_ID_WIDTH(C_AXI_ID_WIDTH),
.C_HAS_AXI_ID(1),
.C_AXI_LEN_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 8 : 4),
.C_AXI_LOCK_WIDTH((C_AXI_PROTOCOL == P_AXI4) ? 1 : 2),
.C_HAS_AXI_ARUSER(1),
.C_HAS_AXI_AWUSER(1),
.C_HAS_AXI_BUSER(1),
.C_HAS_AXI_RUSER(1),
.C_HAS_AXI_WUSER(1),
.C_AXI_ADDR_WIDTH(C_AXI_ADDR_WIDTH),
.C_AXI_ARUSER_WIDTH(C_AXI_ARUSER_WIDTH),
.C_AXI_AWUSER_WIDTH(C_AXI_AWUSER_WIDTH),
.C_AXI_BUSER_WIDTH(C_AXI_BUSER_WIDTH),
.C_AXI_RUSER_WIDTH(C_AXI_RUSER_WIDTH),
.C_AXI_WUSER_WIDTH(C_AXI_WUSER_WIDTH),
.C_DIN_WIDTH_RACH(P_WIDTH_RACH),
.C_DIN_WIDTH_RDCH(P_WIDTH_RDCH),
.C_DIN_WIDTH_WACH(P_WIDTH_WACH),
.C_DIN_WIDTH_WDCH(P_WIDTH_WDCH),
.C_DIN_WIDTH_WRCH(P_WIDTH_WDCH),
.C_RACH_TYPE(((C_AXI_READ_FIFO_DEPTH != 0) && C_AXI_READ_FIFO_DELAY) ? 0 : 2),
.C_WACH_TYPE(((C_AXI_WRITE_FIFO_DEPTH != 0) && C_AXI_WRITE_FIFO_DELAY) ? 0 : 2),
.C_WDCH_TYPE((C_AXI_WRITE_FIFO_DEPTH != 0) ? 0 : 2),
.C_RDCH_TYPE((C_AXI_READ_FIFO_DEPTH != 0) ? 0 : 2),
.C_WRCH_TYPE(2),
.C_COMMON_CLOCK(1),
.C_ADD_NGC_CONSTRAINT(0),
.C_APPLICATION_TYPE_AXIS(0),
.C_APPLICATION_TYPE_RACH(C_AXI_READ_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_RDCH(0),
.C_APPLICATION_TYPE_WACH(C_AXI_WRITE_FIFO_DELAY ? 1 : 0),
.C_APPLICATION_TYPE_WDCH(0),
.C_APPLICATION_TYPE_WRCH(0),
.C_AXIS_TDATA_WIDTH(64),
.C_AXIS_TDEST_WIDTH(4),
.C_AXIS_TID_WIDTH(8),
.C_AXIS_TKEEP_WIDTH(4),
.C_AXIS_TSTRB_WIDTH(4),
.C_AXIS_TUSER_WIDTH(4),
.C_AXIS_TYPE(0),
.C_COUNT_TYPE(0),
.C_DATA_COUNT_WIDTH(10),
.C_DEFAULT_VALUE("BlankString"),
.C_DIN_WIDTH(18),
.C_DIN_WIDTH_AXIS(1),
.C_DOUT_RST_VAL("0"),
.C_DOUT_WIDTH(18),
.C_ENABLE_RLOCS(0),
.C_ENABLE_RST_SYNC(1),
.C_ERROR_INJECTION_TYPE(0),
.C_ERROR_INJECTION_TYPE_AXIS(0),
.C_ERROR_INJECTION_TYPE_RACH(0),
.C_ERROR_INJECTION_TYPE_RDCH(0),
.C_ERROR_INJECTION_TYPE_WACH(0),
.C_ERROR_INJECTION_TYPE_WDCH(0),
.C_ERROR_INJECTION_TYPE_WRCH(0),
.C_FAMILY(C_FAMILY),
.C_FULL_FLAGS_RST_VAL(1),
.C_HAS_ALMOST_EMPTY(0),
.C_HAS_ALMOST_FULL(0),
.C_HAS_AXI_RD_CHANNEL(1),
.C_HAS_AXI_WR_CHANNEL(1),
.C_HAS_AXIS_TDATA(0),
.C_HAS_AXIS_TDEST(0),
.C_HAS_AXIS_TID(0),
.C_HAS_AXIS_TKEEP(0),
.C_HAS_AXIS_TLAST(0),
.C_HAS_AXIS_TREADY(1),
.C_HAS_AXIS_TSTRB(0),
.C_HAS_AXIS_TUSER(0),
.C_HAS_BACKUP(0),
.C_HAS_DATA_COUNT(0),
.C_HAS_DATA_COUNTS_AXIS(0),
.C_HAS_DATA_COUNTS_RACH(0),
.C_HAS_DATA_COUNTS_RDCH(0),
.C_HAS_DATA_COUNTS_WACH(0),
.C_HAS_DATA_COUNTS_WDCH(0),
.C_HAS_DATA_COUNTS_WRCH(0),
.C_HAS_INT_CLK(0),
.C_HAS_MASTER_CE(0),
.C_HAS_MEMINIT_FILE(0),
.C_HAS_OVERFLOW(0),
.C_HAS_PROG_FLAGS_AXIS(0),
.C_HAS_PROG_FLAGS_RACH(0),
.C_HAS_PROG_FLAGS_RDCH(0),
.C_HAS_PROG_FLAGS_WACH(0),
.C_HAS_PROG_FLAGS_WDCH(0),
.C_HAS_PROG_FLAGS_WRCH(0),
.C_HAS_RD_DATA_COUNT(0),
.C_HAS_RD_RST(0),
.C_HAS_RST(1),
.C_HAS_SLAVE_CE(0),
.C_HAS_SRST(0),
.C_HAS_UNDERFLOW(0),
.C_HAS_VALID(0),
.C_HAS_WR_ACK(0),
.C_HAS_WR_DATA_COUNT(0),
.C_HAS_WR_RST(0),
.C_IMPLEMENTATION_TYPE(0),
.C_IMPLEMENTATION_TYPE_AXIS(1),
.C_IMPLEMENTATION_TYPE_RACH(2),
.C_IMPLEMENTATION_TYPE_RDCH((C_AXI_READ_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WACH(2),
.C_IMPLEMENTATION_TYPE_WDCH((C_AXI_WRITE_FIFO_TYPE == "bram") ? 1 : 2),
.C_IMPLEMENTATION_TYPE_WRCH(2),
.C_INIT_WR_PNTR_VAL(0),
.C_MEMORY_TYPE(1),
.C_MIF_FILE_NAME("BlankString"),
.C_MSGON_VAL(1),
.C_OPTIMIZATION_MODE(0),
.C_OVERFLOW_LOW(0),
.C_PRELOAD_LATENCY(1),
.C_PRELOAD_REGS(0),
.C_PRIM_FIFO_TYPE(P_PRIM_FIFO_TYPE),
.C_PROG_EMPTY_THRESH_ASSERT_VAL(2),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_AXIS(1022),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_RDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WACH(30),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WDCH(510),
.C_PROG_EMPTY_THRESH_ASSERT_VAL_WRCH(14),
.C_PROG_EMPTY_THRESH_NEGATE_VAL(3),
.C_PROG_EMPTY_TYPE(0),
.C_PROG_EMPTY_TYPE_AXIS(5),
.C_PROG_EMPTY_TYPE_RACH(5),
.C_PROG_EMPTY_TYPE_RDCH(5),
.C_PROG_EMPTY_TYPE_WACH(5),
.C_PROG_EMPTY_TYPE_WDCH(5),
.C_PROG_EMPTY_TYPE_WRCH(5),
.C_PROG_FULL_THRESH_ASSERT_VAL(1022),
.C_PROG_FULL_THRESH_ASSERT_VAL_AXIS(1023),
.C_PROG_FULL_THRESH_ASSERT_VAL_RACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_RDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WACH(31),
.C_PROG_FULL_THRESH_ASSERT_VAL_WDCH(511),
.C_PROG_FULL_THRESH_ASSERT_VAL_WRCH(15),
.C_PROG_FULL_THRESH_NEGATE_VAL(1021),
.C_PROG_FULL_TYPE(0),
.C_PROG_FULL_TYPE_AXIS(5),
.C_PROG_FULL_TYPE_RACH(5),
.C_PROG_FULL_TYPE_RDCH(5),
.C_PROG_FULL_TYPE_WACH(5),
.C_PROG_FULL_TYPE_WDCH(5),
.C_PROG_FULL_TYPE_WRCH(5),
.C_RD_DATA_COUNT_WIDTH(10),
.C_RD_DEPTH(1024),
.C_RD_FREQ(1),
.C_RD_PNTR_WIDTH(10),
.C_REG_SLICE_MODE_AXIS(0),
.C_REG_SLICE_MODE_RACH(0),
.C_REG_SLICE_MODE_RDCH(0),
.C_REG_SLICE_MODE_WACH(0),
.C_REG_SLICE_MODE_WDCH(0),
.C_REG_SLICE_MODE_WRCH(0),
.C_UNDERFLOW_LOW(0),
.C_USE_COMMON_OVERFLOW(0),
.C_USE_COMMON_UNDERFLOW(0),
.C_USE_DEFAULT_SETTINGS(0),
.C_USE_DOUT_RST(1),
.C_USE_ECC(0),
.C_USE_ECC_AXIS(0),
.C_USE_ECC_RACH(0),
.C_USE_ECC_RDCH(0),
.C_USE_ECC_WACH(0),
.C_USE_ECC_WDCH(0),
.C_USE_ECC_WRCH(0),
.C_USE_EMBEDDED_REG(0),
.C_USE_FIFO16_FLAGS(0),
.C_USE_FWFT_DATA_COUNT(0),
.C_VALID_LOW(0),
.C_WR_ACK_LOW(0),
.C_WR_DATA_COUNT_WIDTH(10),
.C_WR_DEPTH(1024),
.C_WR_DEPTH_AXIS(1024),
.C_WR_DEPTH_RACH(32),
.C_WR_DEPTH_RDCH(C_AXI_READ_FIFO_DEPTH),
.C_WR_DEPTH_WACH(32),
.C_WR_DEPTH_WDCH(C_AXI_WRITE_FIFO_DEPTH),
.C_WR_DEPTH_WRCH(16),
.C_WR_FREQ(1),
.C_WR_PNTR_WIDTH(10),
.C_WR_PNTR_WIDTH_AXIS(10),
.C_WR_PNTR_WIDTH_RACH(5),
.C_WR_PNTR_WIDTH_RDCH((C_AXI_READ_FIFO_DEPTH> 1) ? f_ceil_log2(C_AXI_READ_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WACH(5),
.C_WR_PNTR_WIDTH_WDCH((C_AXI_WRITE_FIFO_DEPTH > 1) ? f_ceil_log2(C_AXI_WRITE_FIFO_DEPTH) : 1),
.C_WR_PNTR_WIDTH_WRCH(4),
.C_WR_RESPONSE_LATENCY(1)
)
fifo_gen_inst (
.s_aclk(aclk),
.s_aresetn(aresetn),
.s_axi_awid(s_axi_awid),
.s_axi_awaddr(s_axi_awaddr),
.s_axi_awlen(s_axi_awlen),
.s_axi_awsize(s_axi_awsize),
.s_axi_awburst(s_axi_awburst),
.s_axi_awlock(s_axi_awlock),
.s_axi_awcache(s_axi_awcache),
.s_axi_awprot(s_axi_awprot),
.s_axi_awqos(s_axi_awqos),
.s_axi_awregion(s_axi_awregion_i),
.s_axi_awuser(s_axi_awuser),
.s_axi_awvalid(s_axi_awvalid),
.s_axi_awready(s_axi_awready),
.s_axi_wid(s_axi_wid_i),
.s_axi_wdata(s_axi_wdata),
.s_axi_wstrb(s_axi_wstrb),
.s_axi_wlast(s_axi_wlast),
.s_axi_wvalid(s_axi_wvalid),
.s_axi_wready(s_axi_wready),
.s_axi_bid(s_axi_bid),
.s_axi_bresp(s_axi_bresp),
.s_axi_bvalid(s_axi_bvalid),
.s_axi_bready(s_axi_bready),
.m_axi_awid(m_axi_awid),
.m_axi_awaddr(m_axi_awaddr),
.m_axi_awlen(m_axi_awlen),
.m_axi_awsize(m_axi_awsize),
.m_axi_awburst(m_axi_awburst),
.m_axi_awlock(m_axi_awlock),
.m_axi_awcache(m_axi_awcache),
.m_axi_awprot(m_axi_awprot),
.m_axi_awqos(m_axi_awqos),
.m_axi_awregion(m_axi_awregion_i),
.m_axi_awuser(m_axi_awuser),
.m_axi_awvalid(m_axi_awvalid),
.m_axi_awready(m_axi_awready),
.m_axi_wid(m_axi_wid_i),
.m_axi_wdata(m_axi_wdata),
.m_axi_wstrb(m_axi_wstrb),
.m_axi_wlast(m_axi_wlast),
.m_axi_wvalid(m_axi_wvalid),
.m_axi_wready(m_axi_wready),
.m_axi_bid(m_axi_bid),
.m_axi_bresp(m_axi_bresp),
.m_axi_bvalid(m_axi_bvalid),
.m_axi_bready(m_axi_bready),
.s_axi_arid(s_axi_arid),
.s_axi_araddr(s_axi_araddr),
.s_axi_arlen(s_axi_arlen),
.s_axi_arsize(s_axi_arsize),
.s_axi_arburst(s_axi_arburst),
.s_axi_arlock(s_axi_arlock),
.s_axi_arcache(s_axi_arcache),
.s_axi_arprot(s_axi_arprot),
.s_axi_arqos(s_axi_arqos),
.s_axi_arregion(s_axi_arregion_i),
.s_axi_arvalid(s_axi_arvalid),
.s_axi_arready(s_axi_arready),
.s_axi_rid(s_axi_rid),
.s_axi_rdata(s_axi_rdata),
.s_axi_rresp(s_axi_rresp),
.s_axi_rlast(s_axi_rlast),
.s_axi_rvalid(s_axi_rvalid),
.s_axi_rready(s_axi_rready),
.m_axi_arid(m_axi_arid),
.m_axi_araddr(m_axi_araddr),
.m_axi_arlen(m_axi_arlen),
.m_axi_arsize(m_axi_arsize),
.m_axi_arburst(m_axi_arburst),
.m_axi_arlock(m_axi_arlock),
.m_axi_arcache(m_axi_arcache),
.m_axi_arprot(m_axi_arprot),
.m_axi_arqos(m_axi_arqos),
.m_axi_arregion(m_axi_arregion_i),
.m_axi_arvalid(m_axi_arvalid),
.m_axi_arready(m_axi_arready),
.m_axi_rid(m_axi_rid),
.m_axi_rdata(m_axi_rdata),
.m_axi_rresp(m_axi_rresp),
.m_axi_rlast(m_axi_rlast),
.m_axi_rvalid(m_axi_rvalid),
.m_axi_rready(m_axi_rready),
.m_aclk(aclk),
.m_aclk_en(1'b1),
.s_aclk_en(1'b1),
.s_axi_wuser(s_axi_wuser),
.s_axi_buser(s_axi_buser),
.m_axi_wuser(m_axi_wuser),
.m_axi_buser(m_axi_buser),
.s_axi_aruser(s_axi_aruser),
.s_axi_ruser(s_axi_ruser),
.m_axi_aruser(m_axi_aruser),
.m_axi_ruser(m_axi_ruser),
.almost_empty(),
.almost_full(),
.axis_data_count(),
.axis_dbiterr(),
.axis_injectdbiterr(1'b0),
.axis_injectsbiterr(1'b0),
.axis_overflow(),
.axis_prog_empty(),
.axis_prog_empty_thresh(10'b0),
.axis_prog_full(),
.axis_prog_full_thresh(10'b0),
.axis_rd_data_count(),
.axis_sbiterr(),
.axis_underflow(),
.axis_wr_data_count(),
.axi_ar_data_count(),
.axi_ar_dbiterr(),
.axi_ar_injectdbiterr(1'b0),
.axi_ar_injectsbiterr(1'b0),
.axi_ar_overflow(),
.axi_ar_prog_empty(),
.axi_ar_prog_empty_thresh(5'b0),
.axi_ar_prog_full(),
.axi_ar_prog_full_thresh(5'b0),
.axi_ar_rd_data_count(),
.axi_ar_sbiterr(),
.axi_ar_underflow(),
.axi_ar_wr_data_count(),
.axi_aw_data_count(),
.axi_aw_dbiterr(),
.axi_aw_injectdbiterr(1'b0),
.axi_aw_injectsbiterr(1'b0),
.axi_aw_overflow(),
.axi_aw_prog_empty(),
.axi_aw_prog_empty_thresh(5'b0),
.axi_aw_prog_full(),
.axi_aw_prog_full_thresh(5'b0),
.axi_aw_rd_data_count(),
.axi_aw_sbiterr(),
.axi_aw_underflow(),
.axi_aw_wr_data_count(),
.axi_b_data_count(),
.axi_b_dbiterr(),
.axi_b_injectdbiterr(1'b0),
.axi_b_injectsbiterr(1'b0),
.axi_b_overflow(),
.axi_b_prog_empty(),
.axi_b_prog_empty_thresh(4'b0),
.axi_b_prog_full(),
.axi_b_prog_full_thresh(4'b0),
.axi_b_rd_data_count(),
.axi_b_sbiterr(),
.axi_b_underflow(),
.axi_b_wr_data_count(),
.axi_r_data_count(),
.axi_r_dbiterr(),
.axi_r_injectdbiterr(1'b0),
.axi_r_injectsbiterr(1'b0),
.axi_r_overflow(),
.axi_r_prog_empty(),
.axi_r_prog_empty_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_prog_full(),
.axi_r_prog_full_thresh({P_READ_FIFO_DEPTH_LOG{1'b0}}),
.axi_r_rd_data_count(),
.axi_r_sbiterr(),
.axi_r_underflow(),
.axi_r_wr_data_count(),
.axi_w_data_count(),
.axi_w_dbiterr(),
.axi_w_injectdbiterr(1'b0),
.axi_w_injectsbiterr(1'b0),
.axi_w_overflow(),
.axi_w_prog_empty(),
.axi_w_prog_empty_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_prog_full(),
.axi_w_prog_full_thresh({P_WRITE_FIFO_DEPTH_LOG{1'b0}}),
.axi_w_rd_data_count(),
.axi_w_sbiterr(),
.axi_w_underflow(),
.axi_w_wr_data_count(),
.backup(1'b0),
.backup_marker(1'b0),
.clk(1'b0),
.data_count(),
.dbiterr(),
.din(18'b0),
.dout(),
.empty(),
.full(),
.injectdbiterr(1'b0),
.injectsbiterr(1'b0),
.int_clk(1'b0),
.m_axis_tdata(),
.m_axis_tdest(),
.m_axis_tid(),
.m_axis_tkeep(),
.m_axis_tlast(),
.m_axis_tready(1'b0),
.m_axis_tstrb(),
.m_axis_tuser(),
.m_axis_tvalid(),
.overflow(),
.prog_empty(),
.prog_empty_thresh(10'b0),
.prog_empty_thresh_assert(10'b0),
.prog_empty_thresh_negate(10'b0),
.prog_full(),
.prog_full_thresh(10'b0),
.prog_full_thresh_assert(10'b0),
.prog_full_thresh_negate(10'b0),
.rd_clk(1'b0),
.rd_data_count(),
.rd_en(1'b0),
.rd_rst(1'b0),
.rst(1'b0),
.sbiterr(),
.srst(1'b0),
.s_axis_tdata(64'b0),
.s_axis_tdest(4'b0),
.s_axis_tid(8'b0),
.s_axis_tkeep(4'b0),
.s_axis_tlast(1'b0),
.s_axis_tready(),
.s_axis_tstrb(4'b0),
.s_axis_tuser(4'b0),
.s_axis_tvalid(1'b0),
.underflow(),
.valid(),
.wr_ack(),
.wr_clk(1'b0),
.wr_data_count(),
.wr_en(1'b0),
.wr_rst(1'b0),
.wr_rst_busy(),
.rd_rst_busy(),
.sleep(1'b0)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
/******************************************************************************
-- (c) Copyright 2006 - 2013 Xilinx, Inc. All rights reserved.
--
-- This file contains confidential and proprietary information
-- of Xilinx, Inc. and is protected under U.S. and
-- international copyright and other intellectual property
-- laws.
--
-- DISCLAIMER
-- This disclaimer is not a license and does not grant any
-- rights to the materials distributed herewith. Except as
-- otherwise provided in a valid license issued to you by
-- Xilinx, and to the maximum extent permitted by applicable
-- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
-- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
-- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
-- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
-- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
-- (2) Xilinx shall not be liable (whether in contract or tort,
-- including negligence, or under any other theory of
-- liability) for any loss or damage of any kind or nature
-- related to, arising under or in connection with these
-- materials, including for any direct, or any indirect,
-- special, incidental, or consequential loss or damage
-- (including loss of data, profits, goodwill, or any type of
-- loss or damage suffered as a result of any action brought
-- by a third party) even if such damage or loss was
-- reasonably foreseeable or Xilinx had been advised of the
-- possibility of the same.
--
-- CRITICAL APPLICATIONS
-- Xilinx products are not designed or intended to be fail-
-- safe, or for use in any application requiring fail-safe
-- performance, such as life-support or safety devices or
-- systems, Class III medical devices, nuclear facilities,
-- applications related to the deployment of airbags, or any
-- other applications that could lead to death, personal
-- injury, or severe property or environmental damage
-- (individually and collectively, "Critical
-- Applications"). Customer assumes the sole risk and
-- liability of any use of Xilinx products in Critical
-- Applications, subject only to applicable laws and
-- regulations governing limitations on product liability.
--
-- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
-- PART OF THIS FILE AT ALL TIMES.
--
*****************************************************************************
*
* Filename: blk_mem_gen_v8_3_5.v
*
* Description:
* This file is the Verilog behvarial model for the
* Block Memory Generator Core.
*
*****************************************************************************
* Author: Xilinx
*
* History: Jan 11, 2006 Initial revision
* Jun 11, 2007 Added independent register stages for
* Port A and Port B (IP1_Jm/v2.5)
* Aug 28, 2007 Added mux pipeline stages feature (IP2_Jm/v2.6)
* Mar 13, 2008 Behavioral model optimizations
* April 07, 2009 : Added support for Spartan-6 and Virtex-6
* features, including the following:
* (i) error injection, detection and/or correction
* (ii) reset priority
* (iii) special reset behavior
*
*****************************************************************************/
`timescale 1ps/1ps
module STATE_LOGIC_v8_3 (O, I0, I1, I2, I3, I4, I5);
parameter INIT = 64'h0000000000000000;
input I0, I1, I2, I3, I4, I5;
output O;
reg O;
reg tmp;
always @( I5 or I4 or I3 or I2 or I1 or I0 ) begin
tmp = I0 ^ I1 ^ I2 ^ I3 ^ I4 ^ I5;
if ( tmp == 0 || tmp == 1)
O = INIT[{I5, I4, I3, I2, I1, I0}];
end
endmodule
module beh_vlog_muxf7_v8_3 (O, I0, I1, S);
output O;
reg O;
input I0, I1, S;
always @(I0 or I1 or S)
if (S)
O = I1;
else
O = I0;
endmodule
module beh_vlog_ff_clr_v8_3 (Q, C, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q<= 1'b0;
else
Q<= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_pre_v8_3 (Q, C, D, PRE);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, D, PRE;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (PRE)
Q <= 1'b1;
else
Q <= #FLOP_DELAY D;
endmodule
module beh_vlog_ff_ce_clr_v8_3 (Q, C, CE, CLR, D);
parameter INIT = 0;
localparam FLOP_DELAY = 100;
output Q;
input C, CE, CLR, D;
reg Q;
initial Q= 1'b0;
always @(posedge C )
if (CLR)
Q <= 1'b0;
else if (CE)
Q <= #FLOP_DELAY D;
endmodule
module write_netlist_v8_3
#(
parameter C_AXI_TYPE = 0
)
(
S_ACLK, S_ARESETN, S_AXI_AWVALID, S_AXI_WVALID, S_AXI_BREADY,
w_last_c, bready_timeout_c, aw_ready_r, S_AXI_WREADY, S_AXI_BVALID,
S_AXI_WR_EN, addr_en_c, incr_addr_c, bvalid_c
);
input S_ACLK;
input S_ARESETN;
input S_AXI_AWVALID;
input S_AXI_WVALID;
input S_AXI_BREADY;
input w_last_c;
input bready_timeout_c;
output aw_ready_r;
output S_AXI_WREADY;
output S_AXI_BVALID;
output S_AXI_WR_EN;
output addr_en_c;
output incr_addr_c;
output bvalid_c;
//-------------------------------------------------------------------------
//AXI LITE
//-------------------------------------------------------------------------
generate if (C_AXI_TYPE == 0 ) begin : gbeh_axi_lite_sm
wire w_ready_r_7;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSignal_bvalid_c;
wire NlwRenamedSignal_incr_addr_c;
wire present_state_FSM_FFd3_13;
wire present_state_FSM_FFd2_14;
wire present_state_FSM_FFd1_15;
wire present_state_FSM_FFd4_16;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd4_In1_21;
wire [0:0] Mmux_aw_ready_c ;
begin
assign
S_AXI_WREADY = w_ready_r_7,
S_AXI_BVALID = NlwRenamedSignal_incr_addr_c,
S_AXI_WR_EN = NlwRenamedSignal_bvalid_c,
incr_addr_c = NlwRenamedSignal_incr_addr_c,
bvalid_c = NlwRenamedSignal_bvalid_c;
assign NlwRenamedSignal_incr_addr_c = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_7)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4 (
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_16)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_13)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_15)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000055554440))
present_state_FSM_FFd3_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088880800))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_AWVALID),
.I1 ( S_AXI_WVALID),
.I2 ( bready_timeout_c),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAA2000))
Mmux_addr_en_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_WVALID),
.I4 ( present_state_FSM_FFd4_16),
.I5 (1'b0),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF5F07570F5F05500))
Mmux_w_ready_c_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd3_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( present_state_FSM_FFd1_15),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1 (
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( present_state_FSM_FFd3_13),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSignal_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h2F0F27072F0F2200))
present_state_FSM_FFd4_In1 (
.I0 ( S_AXI_WVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_13),
.I4 ( present_state_FSM_FFd4_16),
.I5 ( present_state_FSM_FFd2_14),
.O ( present_state_FSM_FFd4_In1_21)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
present_state_FSM_FFd4_In2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_In1_21),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h7535753575305500))
Mmux_aw_ready_c_0_1 (
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_WVALID),
.I3 ( present_state_FSM_FFd4_16),
.I4 ( present_state_FSM_FFd3_13),
.I5 ( present_state_FSM_FFd2_14),
.O ( Mmux_aw_ready_c[0])
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000F8))
Mmux_aw_ready_c_0_2 (
.I0 ( present_state_FSM_FFd1_15),
.I1 ( S_AXI_BREADY),
.I2 ( Mmux_aw_ready_c[0]),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( aw_ready_c)
);
end
end
endgenerate
//---------------------------------------------------------------------
// AXI FULL
//---------------------------------------------------------------------
generate if (C_AXI_TYPE == 1 ) begin : gbeh_axi_full_sm
wire w_ready_r_8;
wire w_ready_c;
wire aw_ready_c;
wire NlwRenamedSig_OI_bvalid_c;
wire present_state_FSM_FFd1_16;
wire present_state_FSM_FFd4_17;
wire present_state_FSM_FFd3_18;
wire present_state_FSM_FFd2_19;
wire present_state_FSM_FFd4_In;
wire present_state_FSM_FFd3_In;
wire present_state_FSM_FFd2_In;
wire present_state_FSM_FFd1_In;
wire present_state_FSM_FFd2_In1_24;
wire present_state_FSM_FFd4_In1_25;
wire N2;
wire N4;
begin
assign
S_AXI_WREADY = w_ready_r_8,
bvalid_c = NlwRenamedSig_OI_bvalid_c,
S_AXI_BVALID = 1'b0;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
aw_ready_r_2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( aw_ready_c),
.Q ( aw_ready_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
w_ready_r
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( w_ready_c),
.Q ( w_ready_r_8)
);
beh_vlog_ff_pre_v8_3 #(
.INIT (1'b1))
present_state_FSM_FFd4
(
.C ( S_ACLK),
.D ( present_state_FSM_FFd4_In),
.PRE ( S_ARESETN),
.Q ( present_state_FSM_FFd4_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd3
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd3_In),
.Q ( present_state_FSM_FFd3_18)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_19)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1
(
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd1_In),
.Q ( present_state_FSM_FFd1_16)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000005540))
present_state_FSM_FFd3_In1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd4_17),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd3_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hBF3FBB33AF0FAA00))
Mmux_aw_ready_c_0_2
(
.I0 ( S_AXI_BREADY),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd1_16),
.I4 ( present_state_FSM_FFd4_17),
.I5 ( NlwRenamedSig_OI_bvalid_c),
.O ( aw_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hAAAAAAAA20000000))
Mmux_addr_en_c_0_1
(
.I0 ( S_AXI_AWVALID),
.I1 ( bready_timeout_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( S_AXI_WVALID),
.I4 ( w_last_c),
.I5 ( present_state_FSM_FFd4_17),
.O ( addr_en_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000A8))
Mmux_S_AXI_WR_EN_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( present_state_FSM_FFd2_19),
.I2 ( present_state_FSM_FFd3_18),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( S_AXI_WR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000002220))
Mmux_incr_addr_c_0_1
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( incr_addr_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000008880))
Mmux_aw_ready_c_0_11
(
.I0 ( S_AXI_WVALID),
.I1 ( w_last_c),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( NlwRenamedSig_OI_bvalid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000D5C0))
present_state_FSM_FFd2_In1
(
.I0 ( w_last_c),
.I1 ( S_AXI_AWVALID),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( present_state_FSM_FFd3_18),
.I4 (1'b0),
.I5 (1'b0),
.O ( present_state_FSM_FFd2_In1_24)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFFFFAAAA08AAAAAA))
present_state_FSM_FFd2_In2
(
.I0 ( present_state_FSM_FFd2_19),
.I1 ( S_AXI_AWVALID),
.I2 ( bready_timeout_c),
.I3 ( w_last_c),
.I4 ( S_AXI_WVALID),
.I5 ( present_state_FSM_FFd2_In1_24),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00C0004000C00000))
present_state_FSM_FFd4_In1
(
.I0 ( S_AXI_AWVALID),
.I1 ( w_last_c),
.I2 ( S_AXI_WVALID),
.I3 ( bready_timeout_c),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( present_state_FSM_FFd4_In1_25)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88F8))
present_state_FSM_FFd4_In2
(
.I0 ( present_state_FSM_FFd1_16),
.I1 ( S_AXI_BREADY),
.I2 ( present_state_FSM_FFd4_17),
.I3 ( S_AXI_AWVALID),
.I4 ( present_state_FSM_FFd4_In1_25),
.I5 (1'b0),
.O ( present_state_FSM_FFd4_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_w_ready_c_0_SW0
(
.I0 ( w_last_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFABAFABAFAAAF000))
Mmux_w_ready_c_0_Q
(
.I0 ( N2),
.I1 ( bready_timeout_c),
.I2 ( S_AXI_AWVALID),
.I3 ( present_state_FSM_FFd4_17),
.I4 ( present_state_FSM_FFd3_18),
.I5 ( present_state_FSM_FFd2_19),
.O ( w_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_aw_ready_c_0_11_SW0
(
.I0 ( bready_timeout_c),
.I1 ( S_AXI_WVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h88808880FFFF8880))
present_state_FSM_FFd1_In1
(
.I0 ( w_last_c),
.I1 ( N4),
.I2 ( present_state_FSM_FFd2_19),
.I3 ( present_state_FSM_FFd3_18),
.I4 ( present_state_FSM_FFd1_16),
.I5 ( S_AXI_BREADY),
.O ( present_state_FSM_FFd1_In)
);
end
end
endgenerate
endmodule
module read_netlist_v8_3 #(
parameter C_AXI_TYPE = 1,
parameter C_ADDRB_WIDTH = 12
) ( S_AXI_R_LAST_INT, S_ACLK, S_ARESETN, S_AXI_ARVALID,
S_AXI_RREADY,S_AXI_INCR_ADDR,S_AXI_ADDR_EN,
S_AXI_SINGLE_TRANS,S_AXI_MUX_SEL, S_AXI_R_LAST, S_AXI_ARREADY,
S_AXI_RLAST, S_AXI_RVALID, S_AXI_RD_EN, S_AXI_ARLEN);
input S_AXI_R_LAST_INT;
input S_ACLK;
input S_ARESETN;
input S_AXI_ARVALID;
input S_AXI_RREADY;
output S_AXI_INCR_ADDR;
output S_AXI_ADDR_EN;
output S_AXI_SINGLE_TRANS;
output S_AXI_MUX_SEL;
output S_AXI_R_LAST;
output S_AXI_ARREADY;
output S_AXI_RLAST;
output S_AXI_RVALID;
output S_AXI_RD_EN;
input [7:0] S_AXI_ARLEN;
wire present_state_FSM_FFd1_13 ;
wire present_state_FSM_FFd2_14 ;
wire gaxi_full_sm_outstanding_read_r_15 ;
wire gaxi_full_sm_ar_ready_r_16 ;
wire gaxi_full_sm_r_last_r_17 ;
wire NlwRenamedSig_OI_gaxi_full_sm_r_valid_r ;
wire gaxi_full_sm_r_valid_c ;
wire S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o ;
wire gaxi_full_sm_ar_ready_c ;
wire gaxi_full_sm_outstanding_read_c ;
wire NlwRenamedSig_OI_S_AXI_R_LAST ;
wire S_AXI_ARLEN_7_GND_8_o_equal_1_o ;
wire present_state_FSM_FFd2_In ;
wire present_state_FSM_FFd1_In ;
wire Mmux_S_AXI_R_LAST13 ;
wire N01 ;
wire N2 ;
wire Mmux_gaxi_full_sm_ar_ready_c11 ;
wire N4 ;
wire N8 ;
wire N9 ;
wire N10 ;
wire N11 ;
wire N12 ;
wire N13 ;
assign
S_AXI_R_LAST = NlwRenamedSig_OI_S_AXI_R_LAST,
S_AXI_ARREADY = gaxi_full_sm_ar_ready_r_16,
S_AXI_RLAST = gaxi_full_sm_r_last_r_17,
S_AXI_RVALID = NlwRenamedSig_OI_gaxi_full_sm_r_valid_r;
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_outstanding_read_r (
.C (S_ACLK),
.CLR(S_ARESETN),
.D(gaxi_full_sm_outstanding_read_c),
.Q(gaxi_full_sm_outstanding_read_r_15)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_r_valid_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (gaxi_full_sm_r_valid_c),
.Q (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
gaxi_full_sm_ar_ready_r (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (gaxi_full_sm_ar_ready_c),
.Q (gaxi_full_sm_ar_ready_r_16)
);
beh_vlog_ff_ce_clr_v8_3 #(
.INIT(1'b0))
gaxi_full_sm_r_last_r (
.C (S_ACLK),
.CE (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.CLR (S_ARESETN),
.D (NlwRenamedSig_OI_S_AXI_R_LAST),
.Q (gaxi_full_sm_r_last_r_17)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd2 (
.C ( S_ACLK),
.CLR ( S_ARESETN),
.D ( present_state_FSM_FFd2_In),
.Q ( present_state_FSM_FFd2_14)
);
beh_vlog_ff_clr_v8_3 #(
.INIT (1'b0))
present_state_FSM_FFd1 (
.C (S_ACLK),
.CLR (S_ARESETN),
.D (present_state_FSM_FFd1_In),
.Q (present_state_FSM_FFd1_13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000000000000B))
S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o1 (
.I0 ( S_AXI_RREADY),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000008))
Mmux_S_AXI_SINGLE_TRANS11 (
.I0 (S_AXI_ARVALID),
.I1 (S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_SINGLE_TRANS)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000004))
Mmux_S_AXI_ADDR_EN11 (
.I0 (present_state_FSM_FFd1_13),
.I1 (S_AXI_ARVALID),
.I2 (1'b0),
.I3 (1'b0),
.I4 (1'b0),
.I5 (1'b0),
.O (S_AXI_ADDR_EN)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hECEE2022EEEE2022))
present_state_FSM_FFd2_In1 (
.I0 ( S_AXI_ARVALID),
.I1 ( present_state_FSM_FFd1_13),
.I2 ( S_AXI_RREADY),
.I3 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.O ( present_state_FSM_FFd2_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000044440444))
Mmux_S_AXI_R_LAST131 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_RREADY),
.I5 (1'b0),
.O ( Mmux_S_AXI_R_LAST13)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h4000FFFF40004000))
Mmux_S_AXI_INCR_ADDR11 (
.I0 ( S_AXI_R_LAST_INT),
.I1 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( Mmux_S_AXI_R_LAST13),
.O ( S_AXI_INCR_ADDR)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000FE))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_SW0 (
.I0 ( S_AXI_ARLEN[2]),
.I1 ( S_AXI_ARLEN[1]),
.I2 ( S_AXI_ARLEN[0]),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N01)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000001))
S_AXI_ARLEN_7_GND_8_o_equal_1_o_7_Q (
.I0 ( S_AXI_ARLEN[7]),
.I1 ( S_AXI_ARLEN[6]),
.I2 ( S_AXI_ARLEN[5]),
.I3 ( S_AXI_ARLEN[4]),
.I4 ( S_AXI_ARLEN[3]),
.I5 ( N01),
.O ( S_AXI_ARLEN_7_GND_8_o_equal_1_o)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000000007))
Mmux_gaxi_full_sm_outstanding_read_c1_SW0 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I2 ( 1'b0),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N2)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0020000002200200))
Mmux_gaxi_full_sm_outstanding_read_c1 (
.I0 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd1_13),
.I3 ( present_state_FSM_FFd2_14),
.I4 ( gaxi_full_sm_outstanding_read_r_15),
.I5 ( N2),
.O ( gaxi_full_sm_outstanding_read_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000000004555))
Mmux_gaxi_full_sm_ar_ready_c12 (
.I0 ( S_AXI_ARVALID),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( Mmux_gaxi_full_sm_ar_ready_c11)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000000000EF))
Mmux_S_AXI_R_LAST11_SW0 (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I3 ( 1'b0),
.I4 ( 1'b0),
.I5 ( 1'b0),
.O ( N4)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hFCAAFC0A00AA000A))
Mmux_S_AXI_R_LAST11 (
.I0 ( S_AXI_ARVALID),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( present_state_FSM_FFd1_13),
.I4 ( N4),
.I5 ( S_AXI_RREADY_gaxi_full_sm_r_valid_r_OR_9_o),
.O ( gaxi_full_sm_r_valid_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000AAAAAA08))
S_AXI_MUX_SEL1 (
.I0 (present_state_FSM_FFd1_13),
.I1 (NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 (S_AXI_RREADY),
.I3 (present_state_FSM_FFd2_14),
.I4 (gaxi_full_sm_outstanding_read_r_15),
.I5 (1'b0),
.O (S_AXI_MUX_SEL)
);
STATE_LOGIC_v8_3 #(
.INIT (64'hF3F3F755A2A2A200))
Mmux_S_AXI_RD_EN11 (
.I0 ( present_state_FSM_FFd1_13),
.I1 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I2 ( S_AXI_RREADY),
.I3 ( gaxi_full_sm_outstanding_read_r_15),
.I4 ( present_state_FSM_FFd2_14),
.I5 ( S_AXI_ARVALID),
.O ( S_AXI_RD_EN)
);
beh_vlog_muxf7_v8_3 present_state_FSM_FFd1_In3 (
.I0 ( N8),
.I1 ( N9),
.S ( present_state_FSM_FFd1_13),
.O ( present_state_FSM_FFd1_In)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000005410F4F0))
present_state_FSM_FFd1_In3_F (
.I0 ( S_AXI_RREADY),
.I1 ( present_state_FSM_FFd2_14),
.I2 ( S_AXI_ARVALID),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I5 ( 1'b0),
.O ( N8)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000072FF7272))
present_state_FSM_FFd1_In3_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N9)
);
beh_vlog_muxf7_v8_3 Mmux_gaxi_full_sm_ar_ready_c14 (
.I0 ( N10),
.I1 ( N11),
.S ( present_state_FSM_FFd1_13),
.O ( gaxi_full_sm_ar_ready_c)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000FFFF88A8))
Mmux_gaxi_full_sm_ar_ready_c14_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_RREADY),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I4 ( Mmux_gaxi_full_sm_ar_ready_c11),
.I5 ( 1'b0),
.O ( N10)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h000000008D008D8D))
Mmux_gaxi_full_sm_ar_ready_c14_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( S_AXI_R_LAST_INT),
.I2 ( gaxi_full_sm_outstanding_read_r_15),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N11)
);
beh_vlog_muxf7_v8_3 Mmux_S_AXI_R_LAST1 (
.I0 ( N12),
.I1 ( N13),
.S ( present_state_FSM_FFd1_13),
.O ( NlwRenamedSig_OI_S_AXI_R_LAST)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h0000000088088888))
Mmux_S_AXI_R_LAST1_F (
.I0 ( S_AXI_ARLEN_7_GND_8_o_equal_1_o),
.I1 ( S_AXI_ARVALID),
.I2 ( present_state_FSM_FFd2_14),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N12)
);
STATE_LOGIC_v8_3 #(
.INIT (64'h00000000E400E4E4))
Mmux_S_AXI_R_LAST1_G (
.I0 ( present_state_FSM_FFd2_14),
.I1 ( gaxi_full_sm_outstanding_read_r_15),
.I2 ( S_AXI_R_LAST_INT),
.I3 ( S_AXI_RREADY),
.I4 ( NlwRenamedSig_OI_gaxi_full_sm_r_valid_r),
.I5 ( 1'b0),
.O ( N13)
);
endmodule
module blk_mem_axi_write_wrapper_beh_v8_3
# (
// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0, // 0: Native Interface; 1: AXI Interface
parameter C_AXI_TYPE = 0, // 0: AXI Lite; 1: AXI Full;
parameter C_AXI_SLAVE_TYPE = 0, // 0: MEMORY SLAVE; 1: PERIPHERAL SLAVE;
parameter C_MEMORY_TYPE = 0, // 0: SP-RAM, 1: SDP-RAM; 2: TDP-RAM; 3: DP-ROM;
parameter C_WRITE_DEPTH_A = 0,
parameter C_AXI_AWADDR_WIDTH = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_WDATA_WIDTH = 32,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
// AXI OUTSTANDING WRITES
parameter C_AXI_OS_WR = 2
)
(
// AXI Global Signals
input S_ACLK,
input S_ARESETN,
// AXI Full/Lite Slave Write Channel (write side)
input [C_AXI_ID_WIDTH-1:0] S_AXI_AWID,
input [C_AXI_AWADDR_WIDTH-1:0] S_AXI_AWADDR,
input [8-1:0] S_AXI_AWLEN,
input [2:0] S_AXI_AWSIZE,
input [1:0] S_AXI_AWBURST,
input S_AXI_AWVALID,
output S_AXI_AWREADY,
input S_AXI_WVALID,
output S_AXI_WREADY,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_BID = 0,
output S_AXI_BVALID,
input S_AXI_BREADY,
// Signals for BMG interface
output [C_ADDRA_WIDTH-1:0] S_AXI_AWADDR_OUT,
output S_AXI_WR_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_AXI_WDATA_WIDTH == 8)?0:
((C_AXI_WDATA_WIDTH==16)?1:
((C_AXI_WDATA_WIDTH==32)?2:
((C_AXI_WDATA_WIDTH==64)?3:
((C_AXI_WDATA_WIDTH==128)?4:
((C_AXI_WDATA_WIDTH==256)?5:0))))));
wire bvalid_c ;
reg bready_timeout_c = 0;
wire [1:0] bvalid_rd_cnt_c;
reg bvalid_r = 0;
reg [2:0] bvalid_count_r = 0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_AWADDR_WIDTH:C_ADDRA_WIDTH)-1:0] awaddr_reg = 0;
reg [1:0] bvalid_wr_cnt_r = 0;
reg [1:0] bvalid_rd_cnt_r = 0;
wire w_last_c ;
wire addr_en_c ;
wire incr_addr_c ;
wire aw_ready_r ;
wire dec_alen_c ;
reg bvalid_d1_c = 0;
reg [7:0] awlen_cntr_r = 0;
reg [7:0] awlen_int = 0;
reg [1:0] awburst_int = 0;
integer total_bytes = 0;
integer wrap_boundary = 0;
integer wrap_base_addr = 0;
integer num_of_bytes_c = 0;
integer num_of_bytes_r = 0;
// Array to store BIDs
reg [C_AXI_ID_WIDTH-1:0] axi_bid_array[3:0] ;
wire S_AXI_BVALID_axi_wr_fsm;
//-------------------------------------
//AXI WRITE FSM COMPONENT INSTANTIATION
//-------------------------------------
write_netlist_v8_3 #(.C_AXI_TYPE(C_AXI_TYPE)) axi_wr_fsm
(
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
.S_AXI_AWVALID(S_AXI_AWVALID),
.aw_ready_r(aw_ready_r),
.S_AXI_WVALID(S_AXI_WVALID),
.S_AXI_WREADY(S_AXI_WREADY),
.S_AXI_BREADY(S_AXI_BREADY),
.S_AXI_WR_EN(S_AXI_WR_EN),
.w_last_c(w_last_c),
.bready_timeout_c(bready_timeout_c),
.addr_en_c(addr_en_c),
.incr_addr_c(incr_addr_c),
.bvalid_c(bvalid_c),
.S_AXI_BVALID (S_AXI_BVALID_axi_wr_fsm)
);
//Wrap Address boundary calculation
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWSIZE:0);
total_bytes = (num_of_bytes_r)*(awlen_int+1);
wrap_base_addr = ((awaddr_reg)/((total_bytes==0)?1:total_bytes))*(total_bytes);
wrap_boundary = wrap_base_addr+total_bytes;
end
//-------------------------------------------------------------------------
// BMG address generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awaddr_reg <= 0;
num_of_bytes_r <= 0;
awburst_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awaddr_reg <= #FLOP_DELAY S_AXI_AWADDR ;
num_of_bytes_r <= num_of_bytes_c;
awburst_int <= ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_AWBURST:2'b01);
end else if (incr_addr_c == 1'b1) begin
if (awburst_int == 2'b10) begin
if(awaddr_reg == (wrap_boundary-num_of_bytes_r)) begin
awaddr_reg <= wrap_base_addr;
end else begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end else if (awburst_int == 2'b01 || awburst_int == 2'b11) begin
awaddr_reg <= awaddr_reg + num_of_bytes_r;
end
end
end
end
assign S_AXI_AWADDR_OUT = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
awaddr_reg[C_AXI_AWADDR_WIDTH-1:C_RANGE]:awaddr_reg);
//-------------------------------------------------------------------------
// AXI wlast generation
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
awlen_cntr_r <= 0;
awlen_int <= 0;
end else begin
if (addr_en_c == 1'b1) begin
awlen_int <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
awlen_cntr_r <= #FLOP_DELAY (C_AXI_TYPE == 0?0:S_AXI_AWLEN) ;
end else if (dec_alen_c == 1'b1) begin
awlen_cntr_r <= #FLOP_DELAY awlen_cntr_r - 1 ;
end
end
end
assign w_last_c = (awlen_cntr_r == 0 && S_AXI_WVALID == 1'b1)?1'b1:1'b0;
assign dec_alen_c = (incr_addr_c | w_last_c);
//-------------------------------------------------------------------------
// Generation of bvalid counter for outstanding transactions
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_count_r <= 0;
end else begin
// bvalid_count_r generation
if (bvalid_c == 1'b1 && bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r ;
end else if (bvalid_c == 1'b1) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r + 1 ;
end else if (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1 && bvalid_count_r != 0) begin
bvalid_count_r <= #FLOP_DELAY bvalid_count_r - 1 ;
end
end
end
//-------------------------------------------------------------------------
// Generation of bvalid when BID is used
//-------------------------------------------------------------------------
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
bvalid_d1_c <= 0;
end else begin
// Delay the generation o bvalid_r for generation for BID
bvalid_d1_c <= bvalid_c;
//external bvalid signal generation
if (bvalid_d1_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of bvalid when BID is not used
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 0) begin:gaxi_bvalid_noid_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_r <= 0;
end else begin
//external bvalid signal generation
if (bvalid_c == 1'b1) begin
bvalid_r <= #FLOP_DELAY 1'b1 ;
end else if (bvalid_count_r <= 1 && S_AXI_BREADY == 1'b1) begin
bvalid_r <= #FLOP_DELAY 0 ;
end
end
end
end
endgenerate
//-------------------------------------------------------------------------
// Generation of Bready timeout
//-------------------------------------------------------------------------
always @(bvalid_count_r) begin
// bready_timeout_c generation
if(bvalid_count_r == C_AXI_OS_WR-1) begin
bready_timeout_c <= 1'b1;
end else begin
bready_timeout_c <= 1'b0;
end
end
//-------------------------------------------------------------------------
// Generation of BID
//-------------------------------------------------------------------------
generate if(C_HAS_AXI_ID == 1) begin:gaxi_bid_gen
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
bvalid_wr_cnt_r <= 0;
bvalid_rd_cnt_r <= 0;
end else begin
// STORE AWID IN AN ARRAY
if(bvalid_c == 1'b1) begin
bvalid_wr_cnt_r <= bvalid_wr_cnt_r + 1;
end
// generate BID FROM AWID ARRAY
bvalid_rd_cnt_r <= #FLOP_DELAY bvalid_rd_cnt_c ;
S_AXI_BID <= axi_bid_array[bvalid_rd_cnt_c];
end
end
assign bvalid_rd_cnt_c = (bvalid_r == 1'b1 && S_AXI_BREADY == 1'b1)?bvalid_rd_cnt_r+1:bvalid_rd_cnt_r;
//-------------------------------------------------------------------------
// Storing AWID for generation of BID
//-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if(S_ARESETN == 1'b1) begin
axi_bid_array[0] = 0;
axi_bid_array[1] = 0;
axi_bid_array[2] = 0;
axi_bid_array[3] = 0;
end else if(aw_ready_r == 1'b1 && S_AXI_AWVALID == 1'b1) begin
axi_bid_array[bvalid_wr_cnt_r] <= S_AXI_AWID;
end
end
end
endgenerate
assign S_AXI_BVALID = bvalid_r;
assign S_AXI_AWREADY = aw_ready_r;
endmodule
module blk_mem_axi_read_wrapper_beh_v8_3
# (
//// AXI Interface related parameters start here
parameter C_INTERFACE_TYPE = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_MEMORY_TYPE = 0,
parameter C_WRITE_WIDTH_A = 4,
parameter C_WRITE_DEPTH_A = 32,
parameter C_ADDRA_WIDTH = 12,
parameter C_AXI_PIPELINE_STAGES = 0,
parameter C_AXI_ARADDR_WIDTH = 12,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_ADDRB_WIDTH = 12
)
(
//// AXI Global Signals
input S_ACLK,
input S_ARESETN,
//// AXI Full/Lite Slave Read (Read side)
input [C_AXI_ARADDR_WIDTH-1:0] S_AXI_ARADDR,
input [7:0] S_AXI_ARLEN,
input [2:0] S_AXI_ARSIZE,
input [1:0] S_AXI_ARBURST,
input S_AXI_ARVALID,
output S_AXI_ARREADY,
output S_AXI_RLAST,
output S_AXI_RVALID,
input S_AXI_RREADY,
input [C_AXI_ID_WIDTH-1:0] S_AXI_ARID,
output reg [C_AXI_ID_WIDTH-1:0] S_AXI_RID = 0,
//// AXI Full/Lite Read Address Signals to BRAM
output [C_ADDRB_WIDTH-1:0] S_AXI_ARADDR_OUT,
output S_AXI_RD_EN
);
localparam FLOP_DELAY = 100; // 100 ps
localparam C_RANGE = ((C_WRITE_WIDTH_A == 8)?0:
((C_WRITE_WIDTH_A==16)?1:
((C_WRITE_WIDTH_A==32)?2:
((C_WRITE_WIDTH_A==64)?3:
((C_WRITE_WIDTH_A==128)?4:
((C_WRITE_WIDTH_A==256)?5:0))))));
reg [C_AXI_ID_WIDTH-1:0] ar_id_r=0;
wire addr_en_c;
wire rd_en_c;
wire incr_addr_c;
wire single_trans_c;
wire dec_alen_c;
wire mux_sel_c;
wire r_last_c;
wire r_last_int_c;
wire [C_ADDRB_WIDTH-1 : 0] araddr_out;
reg [7:0] arlen_int_r=0;
reg [7:0] arlen_cntr=8'h01;
reg [1:0] arburst_int_c=0;
reg [1:0] arburst_int_r=0;
reg [((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?
C_AXI_ARADDR_WIDTH:C_ADDRA_WIDTH)-1:0] araddr_reg =0;
integer num_of_bytes_c = 0;
integer total_bytes = 0;
integer num_of_bytes_r = 0;
integer wrap_base_addr_r = 0;
integer wrap_boundary_r = 0;
reg [7:0] arlen_int_c=0;
integer total_bytes_c = 0;
integer wrap_base_addr_c = 0;
integer wrap_boundary_c = 0;
assign dec_alen_c = incr_addr_c | r_last_int_c;
read_netlist_v8_3
#(.C_AXI_TYPE (1),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_read_fsm (
.S_AXI_INCR_ADDR(incr_addr_c),
.S_AXI_ADDR_EN(addr_en_c),
.S_AXI_SINGLE_TRANS(single_trans_c),
.S_AXI_MUX_SEL(mux_sel_c),
.S_AXI_R_LAST(r_last_c),
.S_AXI_R_LAST_INT(r_last_int_c),
//// AXI Global Signals
.S_ACLK(S_ACLK),
.S_ARESETN(S_ARESETN),
//// AXI Full/Lite Slave Read (Read side)
.S_AXI_ARLEN(S_AXI_ARLEN),
.S_AXI_ARVALID(S_AXI_ARVALID),
.S_AXI_ARREADY(S_AXI_ARREADY),
.S_AXI_RLAST(S_AXI_RLAST),
.S_AXI_RVALID(S_AXI_RVALID),
.S_AXI_RREADY(S_AXI_RREADY),
//// AXI Full/Lite Read Address Signals to BRAM
.S_AXI_RD_EN(rd_en_c)
);
always@(*) begin
num_of_bytes_c = 2**((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARSIZE:0);
total_bytes = (num_of_bytes_r)*(arlen_int_r+1);
wrap_base_addr_r = ((araddr_reg)/(total_bytes==0?1:total_bytes))*(total_bytes);
wrap_boundary_r = wrap_base_addr_r+total_bytes;
//////// combinatorial from interface
arlen_int_c = (C_AXI_TYPE == 0?0:S_AXI_ARLEN);
total_bytes_c = (num_of_bytes_c)*(arlen_int_c+1);
wrap_base_addr_c = ((S_AXI_ARADDR)/(total_bytes_c==0?1:total_bytes_c))*(total_bytes_c);
wrap_boundary_c = wrap_base_addr_c+total_bytes_c;
arburst_int_c = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARBURST:1);
end
////-------------------------------------------------------------------------
//// BMG address generation
////-------------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
araddr_reg <= 0;
arburst_int_r <= 0;
num_of_bytes_r <= 0;
end else begin
if (incr_addr_c == 1'b1 && addr_en_c == 1'b1 && single_trans_c == 1'b0) begin
arburst_int_r <= arburst_int_c;
num_of_bytes_r <= num_of_bytes_c;
if (arburst_int_c == 2'b10) begin
if(S_AXI_ARADDR == (wrap_boundary_c-num_of_bytes_c)) begin
araddr_reg <= wrap_base_addr_c;
end else begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (arburst_int_c == 2'b01 || arburst_int_c == 2'b11) begin
araddr_reg <= S_AXI_ARADDR + num_of_bytes_c;
end
end else if (addr_en_c == 1'b1) begin
araddr_reg <= S_AXI_ARADDR;
num_of_bytes_r <= num_of_bytes_c;
arburst_int_r <= arburst_int_c;
end else if (incr_addr_c == 1'b1) begin
if (arburst_int_r == 2'b10) begin
if(araddr_reg == (wrap_boundary_r-num_of_bytes_r)) begin
araddr_reg <= wrap_base_addr_r;
end else begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end else if (arburst_int_r == 2'b01 || arburst_int_r == 2'b11) begin
araddr_reg <= araddr_reg + num_of_bytes_r;
end
end
end
end
assign araddr_out = ((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?araddr_reg[C_AXI_ARADDR_WIDTH-1:C_RANGE]:araddr_reg);
////-----------------------------------------------------------------------
//// Counter to generate r_last_int_c from registered ARLEN - AXI FULL FSM
////-----------------------------------------------------------------------
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
arlen_cntr <= 8'h01;
arlen_int_r <= 0;
end else begin
if (addr_en_c == 1'b1 && dec_alen_c == 1'b1 && single_trans_c == 1'b0) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= S_AXI_ARLEN - 1'b1;
end else if (addr_en_c == 1'b1) begin
arlen_int_r <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
arlen_cntr <= (C_AXI_TYPE == 0?0:S_AXI_ARLEN) ;
end else if (dec_alen_c == 1'b1) begin
arlen_cntr <= arlen_cntr - 1'b1 ;
end
else begin
arlen_cntr <= arlen_cntr;
end
end
end
assign r_last_int_c = (arlen_cntr == 0 && S_AXI_RREADY == 1'b1)?1'b1:1'b0;
////------------------------------------------------------------------------
//// AXI FULL FSM
//// Mux Selection of ARADDR
//// ARADDR is driven out from the read fsm based on the mux_sel_c
//// Based on mux_sel either ARADDR is given out or the latched ARADDR is
//// given out to BRAM
////------------------------------------------------------------------------
assign S_AXI_ARADDR_OUT = (mux_sel_c == 1'b0)?((C_AXI_TYPE == 1 && C_AXI_SLAVE_TYPE == 0)?S_AXI_ARADDR[C_AXI_ARADDR_WIDTH-1:C_RANGE]:S_AXI_ARADDR):araddr_out;
////------------------------------------------------------------------------
//// Assign output signals - AXI FULL FSM
////------------------------------------------------------------------------
assign S_AXI_RD_EN = rd_en_c;
generate if (C_HAS_AXI_ID == 1) begin:gaxi_bvalid_id_r
always @(posedge S_ACLK or S_ARESETN) begin
if (S_ARESETN == 1'b1) begin
S_AXI_RID <= 0;
ar_id_r <= 0;
end else begin
if (addr_en_c == 1'b1 && rd_en_c == 1'b1) begin
S_AXI_RID <= S_AXI_ARID;
ar_id_r <= S_AXI_ARID;
end else if (addr_en_c == 1'b1 && rd_en_c == 1'b0) begin
ar_id_r <= S_AXI_ARID;
end else if (rd_en_c == 1'b1) begin
S_AXI_RID <= ar_id_r;
end
end
end
end
endgenerate
endmodule
module blk_mem_axi_regs_fwd_v8_3
#(parameter C_DATA_WIDTH = 8
)(
input ACLK,
input ARESET,
input S_VALID,
output S_READY,
input [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
output M_VALID,
input M_READY,
output reg [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA
);
reg [C_DATA_WIDTH-1:0] STORAGE_DATA;
wire S_READY_I;
reg M_VALID_I;
reg [1:0] ARESET_D;
//assign local signal to its output signal
assign S_READY = S_READY_I;
assign M_VALID = M_VALID_I;
always @(posedge ACLK) begin
ARESET_D <= {ARESET_D[0], ARESET};
end
//Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK or ARESET) begin
if (ARESET == 1'b1) begin
STORAGE_DATA <= 0;
end else begin
if(S_VALID == 1'b1 && S_READY_I == 1'b1 ) begin
STORAGE_DATA <= S_PAYLOAD_DATA;
end
end
end
always @(posedge ACLK) begin
M_PAYLOAD_DATA = STORAGE_DATA;
end
//M_Valid set to high when we have a completed transfer on slave side
//Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK or ARESET_D) begin
if (ARESET_D != 2'b00) begin
M_VALID_I <= 1'b0;
end else begin
if (S_VALID == 1'b1) begin
//Always set M_VALID_I when slave side is valid
M_VALID_I <= 1'b1;
end else if (M_READY == 1'b1 ) begin
//Clear (or keep) when no slave side is valid but master side is ready
M_VALID_I <= 1'b0;
end
end
end
//Slave Ready is either when Master side drives M_READY or we have space in our storage data
assign S_READY_I = (M_READY || (!M_VALID_I)) && !(|(ARESET_D));
endmodule
//*****************************************************************************
// Output Register Stage module
//
// This module builds the output register stages of the memory. This module is
// instantiated in the main memory module (blk_mem_gen_v8_3_5) which is
// declared/implemented further down in this file.
//*****************************************************************************
module blk_mem_gen_v8_3_5_output_stage
#(parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RST = 0,
parameter C_RSTRAM = 0,
parameter C_RST_PRIORITY = "CE",
parameter C_INIT_VAL = "0",
parameter C_HAS_EN = 0,
parameter C_HAS_REGCE = 0,
parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_MEM_OUTPUT_REGS = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter NUM_STAGES = 1,
parameter C_EN_ECC_PIPE = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input RST,
input EN,
input REGCE,
input [C_DATA_WIDTH-1:0] DIN_I,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN_I,
input DBITERR_IN_I,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN_I,
input ECCPIPECE,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RST : Determines the presence of the RST port
// C_RSTRAM : Determines if special reset behavior is used
// C_RST_PRIORITY : Determines the priority between CE and SR
// C_INIT_VAL : Initialization value
// C_HAS_EN : Determines the presence of the EN port
// C_HAS_REGCE : Determines the presence of the REGCE port
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// NUM_STAGES : Determines the number of output stages
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// RST : Reset input to reset memory outputs to a user-defined
// reset state
// EN : Enable all read and write operations
// REGCE : Register Clock Enable to control each pipeline output
// register stages
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
// Fix for CR-509792
localparam REG_STAGES = (NUM_STAGES < 2) ? 1 : NUM_STAGES-1;
// Declare the pipeline registers
// (includes mem output reg, mux pipeline stages, and mux output reg)
reg [C_DATA_WIDTH*REG_STAGES-1:0] out_regs;
reg [C_ADDRB_WIDTH*REG_STAGES-1:0] rdaddrecc_regs;
reg [REG_STAGES-1:0] sbiterr_regs;
reg [REG_STAGES-1:0] dbiterr_regs;
reg [C_DATA_WIDTH*8-1:0] init_str = C_INIT_VAL;
reg [C_DATA_WIDTH-1:0] init_val ;
//*********************************************
// Wire off optional inputs based on parameters
//*********************************************
wire en_i;
wire regce_i;
wire rst_i;
// Internal signals
reg [C_DATA_WIDTH-1:0] DIN;
reg [C_ADDRB_WIDTH-1:0] RDADDRECC_IN;
reg SBITERR_IN;
reg DBITERR_IN;
// Internal enable for output registers is tied to user EN or '1' depending
// on parameters
assign en_i = (C_HAS_EN==0 || EN);
// Internal register enable for output registers is tied to user REGCE, EN or
// '1' depending on parameters
// For V4 ECC, REGCE is always 1
// Virtex-4 ECC Not Yet Supported
assign regce_i = ((C_HAS_REGCE==1) && REGCE) ||
((C_HAS_REGCE==0) && (C_HAS_EN==0 || EN));
//Internal SRR is tied to user RST or '0' depending on parameters
assign rst_i = (C_HAS_RST==1) && RST;
//****************************************************
// Power on: load up the output registers and latches
//****************************************************
initial begin
if (!($sscanf(init_str, "%h", init_val))) begin
init_val = 0;
end
DOUT = init_val;
RDADDRECC = 0;
SBITERR = 1'b0;
DBITERR = 1'b0;
DIN = {(C_DATA_WIDTH){1'b0}};
RDADDRECC_IN = 0;
SBITERR_IN = 0;
DBITERR_IN = 0;
// This will be one wider than need, but 0 is an error
out_regs = {(REG_STAGES+1){init_val}};
rdaddrecc_regs = 0;
sbiterr_regs = {(REG_STAGES+1){1'b0}};
dbiterr_regs = {(REG_STAGES+1){1'b0}};
end
//***********************************************
// NUM_STAGES = 0 (No output registers. RAM only)
//***********************************************
generate if (NUM_STAGES == 0) begin : zero_stages
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 0) begin : no_ecc_pipe_reg
always @* begin
DIN = DIN_I;
SBITERR_IN = SBITERR_IN_I;
DBITERR_IN = DBITERR_IN_I;
RDADDRECC_IN = RDADDRECC_IN_I;
end
end
endgenerate
generate if (C_EN_ECC_PIPE == 1) begin : with_ecc_pipe_reg
always @(posedge CLK) begin
if(ECCPIPECE == 1) begin
DIN <= #FLOP_DELAY DIN_I;
SBITERR_IN <= #FLOP_DELAY SBITERR_IN_I;
DBITERR_IN <= #FLOP_DELAY DBITERR_IN_I;
RDADDRECC_IN <= #FLOP_DELAY RDADDRECC_IN_I;
end
end
end
endgenerate
//***********************************************
// NUM_STAGES = 1
// (Mem Output Reg only or Mux Output Reg only)
//***********************************************
// Possible valid combinations:
// Note: C_HAS_MUX_OUTPUT_REGS_*=0 when (C_RSTRAM_*=1)
// +-----------------------------------------+
// | C_RSTRAM_* | Reset Behavior |
// +----------------+------------------------+
// | 0 | Normal Behavior |
// +----------------+------------------------+
// | 1 | Special Behavior |
// +----------------+------------------------+
//
// Normal = REGCE gates reset, as in the case of all families except S3ADSP.
// Special = EN gates reset, as in the case of S3ADSP.
generate if (NUM_STAGES == 1 &&
(C_RSTRAM == 0 || (C_RSTRAM == 1 && (C_XDEVICEFAMILY != "spartan3adsp" && C_XDEVICEFAMILY != "aspartan3adsp" )) ||
C_HAS_MEM_OUTPUT_REGS == 0 || C_HAS_RST == 0))
begin : one_stages_norm
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY DIN;
RDADDRECC <= #FLOP_DELAY RDADDRECC_IN;
SBITERR <= #FLOP_DELAY SBITERR_IN;
DBITERR <= #FLOP_DELAY DBITERR_IN;
end //Output signal assignments
end //end Priority conditions
end //end RST Type conditions
end //end one_stages_norm generate statement
endgenerate
// Special Reset Behavior for S3ADSP
generate if (NUM_STAGES == 1 && C_RSTRAM == 1 && (C_XDEVICEFAMILY =="spartan3adsp" || C_XDEVICEFAMILY =="aspartan3adsp"))
begin : one_stage_splbhv
always @(posedge CLK) begin
if (en_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
end else if (regce_i && !rst_i) begin
DOUT <= #FLOP_DELAY DIN;
end //Output signal assignments
end //end CLK
end //end one_stage_splbhv generate statement
endgenerate
//************************************************************
// NUM_STAGES > 1
// Mem Output Reg + Mux Output Reg
// or
// Mem Output Reg + Mux Pipeline Stages (>0) + Mux Output Reg
// or
// Mux Pipeline Stages (>0) + Mux Output Reg
//*************************************************************
generate if (NUM_STAGES > 1) begin : multi_stage
//Asynchronous Reset
always @(posedge CLK) begin
if (C_RST_PRIORITY == "CE") begin //REGCE has priority
if (regce_i && rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end else begin //RST has priority
if (rst_i) begin
DOUT <= #FLOP_DELAY init_val;
RDADDRECC <= #FLOP_DELAY 0;
SBITERR <= #FLOP_DELAY 1'b0;
DBITERR <= #FLOP_DELAY 1'b0;
end else if (regce_i) begin
DOUT <= #FLOP_DELAY
out_regs[C_DATA_WIDTH*(NUM_STAGES-2)+:C_DATA_WIDTH];
RDADDRECC <= #FLOP_DELAY rdaddrecc_regs[C_ADDRB_WIDTH*(NUM_STAGES-2)+:C_ADDRB_WIDTH];
SBITERR <= #FLOP_DELAY sbiterr_regs[NUM_STAGES-2];
DBITERR <= #FLOP_DELAY dbiterr_regs[NUM_STAGES-2];
end //Output signal assignments
end //end Priority conditions
// Shift the data through the output stages
if (en_i) begin
out_regs <= #FLOP_DELAY (out_regs << C_DATA_WIDTH) | DIN;
rdaddrecc_regs <= #FLOP_DELAY (rdaddrecc_regs << C_ADDRB_WIDTH) | RDADDRECC_IN;
sbiterr_regs <= #FLOP_DELAY (sbiterr_regs << 1) | SBITERR_IN;
dbiterr_regs <= #FLOP_DELAY (dbiterr_regs << 1) | DBITERR_IN;
end
end //end CLK
end //end multi_stage generate statement
endgenerate
endmodule
module blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(parameter C_DATA_WIDTH = 32,
parameter C_ADDRB_WIDTH = 10,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_USE_SOFTECC = 0,
parameter FLOP_DELAY = 100
)
(
input CLK,
input [C_DATA_WIDTH-1:0] DIN,
output reg [C_DATA_WIDTH-1:0] DOUT,
input SBITERR_IN,
input DBITERR_IN,
output reg SBITERR,
output reg DBITERR,
input [C_ADDRB_WIDTH-1:0] RDADDRECC_IN,
output reg [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_DATA_WIDTH : Memory write/read width
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_SOFTECC_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// FLOP_DELAY : Constant delay for register assignments
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLK : Clock to synchronize all read and write operations
// DIN : Data input to the Output stage.
// DOUT : Final Data output
// SBITERR_IN : SBITERR input signal to the Output stage.
// SBITERR : Final SBITERR Output signal.
// DBITERR_IN : DBITERR input signal to the Output stage.
// DBITERR : Final DBITERR Output signal.
// RDADDRECC_IN : RDADDRECC input signal to the Output stage.
// RDADDRECC : Final RDADDRECC Output signal.
//////////////////////////////////////////////////////////////////////////
reg [C_DATA_WIDTH-1:0] dout_i = 0;
reg sbiterr_i = 0;
reg dbiterr_i = 0;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_i = 0;
//***********************************************
// NO OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==0) begin : no_output_stage
always @* begin
DOUT = DIN;
RDADDRECC = RDADDRECC_IN;
SBITERR = SBITERR_IN;
DBITERR = DBITERR_IN;
end
end
endgenerate
//***********************************************
// WITH OUTPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_OUTPUT_REGS_B==1) begin : has_output_stage
always @(posedge CLK) begin
dout_i <= #FLOP_DELAY DIN;
rdaddrecc_i <= #FLOP_DELAY RDADDRECC_IN;
sbiterr_i <= #FLOP_DELAY SBITERR_IN;
dbiterr_i <= #FLOP_DELAY DBITERR_IN;
end
always @* begin
DOUT = dout_i;
RDADDRECC = rdaddrecc_i;
SBITERR = sbiterr_i;
DBITERR = dbiterr_i;
end //end always
end //end in_or_out_stage generate statement
endgenerate
endmodule
//*****************************************************************************
// Main Memory module
//
// This module is the top-level behavioral model and this implements the RAM
//*****************************************************************************
module blk_mem_gen_v8_3_5_mem_module
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter FLOP_DELAY = 100,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input CLKA,
input RSTA,
input ENA,
input REGCEA,
input [C_WEA_WIDTH-1:0] WEA,
input [C_ADDRA_WIDTH-1:0] ADDRA,
input [C_WRITE_WIDTH_A-1:0] DINA,
output [C_READ_WIDTH_A-1:0] DOUTA,
input CLKB,
input RSTB,
input ENB,
input REGCEB,
input [C_WEB_WIDTH-1:0] WEB,
input [C_ADDRB_WIDTH-1:0] ADDRB,
input [C_WRITE_WIDTH_B-1:0] DINB,
output [C_READ_WIDTH_B-1:0] DOUTB,
input INJECTSBITERR,
input INJECTDBITERR,
input ECCPIPECE,
input SLEEP,
output SBITERR,
output DBITERR,
output [C_ADDRB_WIDTH-1:0] RDADDRECC
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
// Note: C_CORENAME parameter is hard-coded to "blk_mem_gen_v8_3_5" and it is
// only used by this module to print warning messages. It is neither passed
// down from blk_mem_gen_v8_3_5_xst.v nor present in the instantiation template
// coregen generates
//***************************************************************************
// constants for the core behavior
//***************************************************************************
// file handles for logging
//--------------------------------------------------
localparam ADDRFILE = 32'h8000_0001; //stdout for addr out of range
localparam COLLFILE = 32'h8000_0001; //stdout for coll detection
localparam ERRFILE = 32'h8000_0001; //stdout for file I/O errors
// other constants
//--------------------------------------------------
localparam COLL_DELAY = 100; // 100 ps
// locally derived parameters to determine memory shape
//-----------------------------------------------------
localparam CHKBIT_WIDTH = (C_WRITE_WIDTH_A>57 ? 8 : (C_WRITE_WIDTH_A>26 ? 7 : (C_WRITE_WIDTH_A>11 ? 6 : (C_WRITE_WIDTH_A>4 ? 5 : (C_WRITE_WIDTH_A<5 ? 4 :0)))));
localparam MIN_WIDTH_A = (C_WRITE_WIDTH_A < C_READ_WIDTH_A) ?
C_WRITE_WIDTH_A : C_READ_WIDTH_A;
localparam MIN_WIDTH_B = (C_WRITE_WIDTH_B < C_READ_WIDTH_B) ?
C_WRITE_WIDTH_B : C_READ_WIDTH_B;
localparam MIN_WIDTH = (MIN_WIDTH_A < MIN_WIDTH_B) ?
MIN_WIDTH_A : MIN_WIDTH_B;
localparam MAX_DEPTH_A = (C_WRITE_DEPTH_A > C_READ_DEPTH_A) ?
C_WRITE_DEPTH_A : C_READ_DEPTH_A;
localparam MAX_DEPTH_B = (C_WRITE_DEPTH_B > C_READ_DEPTH_B) ?
C_WRITE_DEPTH_B : C_READ_DEPTH_B;
localparam MAX_DEPTH = (MAX_DEPTH_A > MAX_DEPTH_B) ?
MAX_DEPTH_A : MAX_DEPTH_B;
// locally derived parameters to assist memory access
//----------------------------------------------------
// Calculate the width ratios of each port with respect to the narrowest
// port
localparam WRITE_WIDTH_RATIO_A = C_WRITE_WIDTH_A/MIN_WIDTH;
localparam READ_WIDTH_RATIO_A = C_READ_WIDTH_A/MIN_WIDTH;
localparam WRITE_WIDTH_RATIO_B = C_WRITE_WIDTH_B/MIN_WIDTH;
localparam READ_WIDTH_RATIO_B = C_READ_WIDTH_B/MIN_WIDTH;
// To modify the LSBs of the 'wider' data to the actual
// address value
//----------------------------------------------------
localparam WRITE_ADDR_A_DIV = C_WRITE_WIDTH_A/MIN_WIDTH_A;
localparam READ_ADDR_A_DIV = C_READ_WIDTH_A/MIN_WIDTH_A;
localparam WRITE_ADDR_B_DIV = C_WRITE_WIDTH_B/MIN_WIDTH_B;
localparam READ_ADDR_B_DIV = C_READ_WIDTH_B/MIN_WIDTH_B;
// If byte writes aren't being used, make sure BYTE_SIZE is not
// wider than the memory elements to avoid compilation warnings
localparam BYTE_SIZE = (C_BYTE_SIZE < MIN_WIDTH) ? C_BYTE_SIZE : MIN_WIDTH;
// The memory
reg [MIN_WIDTH-1:0] memory [0:MAX_DEPTH-1];
reg [MIN_WIDTH-1:0] temp_mem_array [0:MAX_DEPTH-1];
reg [C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:0] doublebit_error = 3;
// ECC error arrays
reg sbiterr_arr [0:MAX_DEPTH-1];
reg dbiterr_arr [0:MAX_DEPTH-1];
reg softecc_sbiterr_arr [0:MAX_DEPTH-1];
reg softecc_dbiterr_arr [0:MAX_DEPTH-1];
// Memory output 'latches'
reg [C_READ_WIDTH_A-1:0] memory_out_a;
reg [C_READ_WIDTH_B-1:0] memory_out_b;
// ECC error inputs and outputs from output_stage module:
reg sbiterr_in;
wire sbiterr_sdp;
reg dbiterr_in;
wire dbiterr_sdp;
wire [C_READ_WIDTH_B-1:0] dout_i;
wire dbiterr_i;
wire sbiterr_i;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_i;
reg [C_ADDRB_WIDTH-1:0] rdaddrecc_in;
wire [C_ADDRB_WIDTH-1:0] rdaddrecc_sdp;
// Reset values
reg [C_READ_WIDTH_A-1:0] inita_val;
reg [C_READ_WIDTH_B-1:0] initb_val;
// Collision detect
reg is_collision;
reg is_collision_a, is_collision_delay_a;
reg is_collision_b, is_collision_delay_b;
// Temporary variables for initialization
//---------------------------------------
integer status;
integer initfile;
integer meminitfile;
// data input buffer
reg [C_WRITE_WIDTH_A-1:0] mif_data;
reg [C_WRITE_WIDTH_A-1:0] mem_data;
// string values in hex
reg [C_READ_WIDTH_A*8-1:0] inita_str = C_INITA_VAL;
reg [C_READ_WIDTH_B*8-1:0] initb_str = C_INITB_VAL;
reg [C_WRITE_WIDTH_A*8-1:0] default_data_str = C_DEFAULT_DATA;
// initialization filename
reg [1023*8-1:0] init_file_str = C_INIT_FILE_NAME;
reg [1023*8-1:0] mem_init_file_str = C_INIT_FILE;
//Constants used to calculate the effective address widths for each of the
//four ports.
integer cnt = 1;
integer write_addr_a_width, read_addr_a_width;
integer write_addr_b_width, read_addr_b_width;
localparam C_FAMILY_LOCALPARAM = (C_FAMILY=="zynquplus"?"virtex7":(C_FAMILY=="kintexuplus"?"virtex7":(C_FAMILY=="virtexuplus"?"virtex7":(C_FAMILY=="virtexu"?"virtex7":(C_FAMILY=="kintexu" ? "virtex7":(C_FAMILY=="virtex7" ? "virtex7" : (C_FAMILY=="virtex7l" ? "virtex7" : (C_FAMILY=="qvirtex7" ? "virtex7" : (C_FAMILY=="qvirtex7l" ? "virtex7" : (C_FAMILY=="kintex7" ? "virtex7" : (C_FAMILY=="kintex7l" ? "virtex7" : (C_FAMILY=="qkintex7" ? "virtex7" : (C_FAMILY=="qkintex7l" ? "virtex7" : (C_FAMILY=="artix7" ? "virtex7" : (C_FAMILY=="artix7l" ? "virtex7" : (C_FAMILY=="qartix7" ? "virtex7" : (C_FAMILY=="qartix7l" ? "virtex7" : (C_FAMILY=="aartix7" ? "virtex7" : (C_FAMILY=="zynq" ? "virtex7" : (C_FAMILY=="azynq" ? "virtex7" : (C_FAMILY=="qzynq" ? "virtex7" : C_FAMILY)))))))))))))))))))));
// Internal configuration parameters
//---------------------------------------------
localparam SINGLE_PORT = (C_MEM_TYPE==0 || C_MEM_TYPE==3);
localparam IS_ROM = (C_MEM_TYPE==3 || C_MEM_TYPE==4);
localparam HAS_A_WRITE = (!IS_ROM);
localparam HAS_B_WRITE = (C_MEM_TYPE==2);
localparam HAS_A_READ = (C_MEM_TYPE!=1);
localparam HAS_B_READ = (!SINGLE_PORT);
localparam HAS_B_PORT = (HAS_B_READ || HAS_B_WRITE);
// Calculate the mux pipeline register stages for Port A and Port B
//------------------------------------------------------------------
localparam MUX_PIPELINE_STAGES_A = (C_HAS_MUX_OUTPUT_REGS_A) ?
C_MUX_PIPELINE_STAGES : 0;
localparam MUX_PIPELINE_STAGES_B = (C_HAS_MUX_OUTPUT_REGS_B) ?
C_MUX_PIPELINE_STAGES : 0;
// Calculate total number of register stages in the core
// -----------------------------------------------------
localparam NUM_OUTPUT_STAGES_A = (C_HAS_MEM_OUTPUT_REGS_A+MUX_PIPELINE_STAGES_A+C_HAS_MUX_OUTPUT_REGS_A);
localparam NUM_OUTPUT_STAGES_B = (C_HAS_MEM_OUTPUT_REGS_B+MUX_PIPELINE_STAGES_B+C_HAS_MUX_OUTPUT_REGS_B);
wire ena_i;
wire enb_i;
wire reseta_i;
wire resetb_i;
wire [C_WEA_WIDTH-1:0] wea_i;
wire [C_WEB_WIDTH-1:0] web_i;
wire rea_i;
wire reb_i;
wire rsta_outp_stage;
wire rstb_outp_stage;
// ECC SBITERR/DBITERR Outputs
// The ECC Behavior is modeled by the behavioral models only for Virtex-6.
// For Virtex-5, these outputs will be tied to 0.
assign SBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?sbiterr_sdp:0;
assign DBITERR = ((C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?dbiterr_sdp:0;
assign RDADDRECC = (((C_FAMILY_LOCALPARAM == "virtex7") && C_MEM_TYPE == 1 && C_USE_ECC == 1) || C_USE_SOFTECC == 1)?rdaddrecc_sdp:0;
// This effectively wires off optional inputs
assign ena_i = (C_HAS_ENA==0) || ENA;
assign enb_i = ((C_HAS_ENB==0) || ENB) && HAS_B_PORT;
// To match RTL : In RTL, write enable of the primitive is tied to all 1's and
// the enable of the primitive is ANDing of wea(0) and ena. so eventually, the
// write operation depends on both enable and write enable. So, the below code
// which is actually doing the write operation only on enable ignoring the wea
// is removed to be in consistent with RTL.
// To Fix CR855535 (The fix to this CR is reverted to match RTL)
//assign wea_i = (HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 1 && ENA == 1) ? 'b1 :(HAS_A_WRITE == 1 && C_MEM_TYPE == 1 &&C_USE_ECC == 1 && C_HAS_ENA == 0) ? WEA : (HAS_A_WRITE && ena_i && C_USE_ECC == 0) ? WEA : 'b0;
assign wea_i = (HAS_A_WRITE && ena_i) ? WEA : 'b0;
assign web_i = (HAS_B_WRITE && enb_i) ? WEB : 'b0;
assign rea_i = (HAS_A_READ) ? ena_i : 'b0;
assign reb_i = (HAS_B_READ) ? enb_i : 'b0;
// These signals reset the memory latches
assign reseta_i =
((C_HAS_RSTA==1 && RSTA && NUM_OUTPUT_STAGES_A==0) ||
(C_HAS_RSTA==1 && RSTA && C_RSTRAM_A==1));
assign resetb_i =
((C_HAS_RSTB==1 && RSTB && NUM_OUTPUT_STAGES_B==0) ||
(C_HAS_RSTB==1 && RSTB && C_RSTRAM_B==1));
// Tasks to access the memory
//---------------------------
//**************
// write_a
//**************
task write_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg [C_WEA_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_A-1:0] data,
input inj_sbiterr,
input inj_dbiterr);
reg [C_WRITE_WIDTH_A-1:0] current_contents;
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_A_DIV);
if (address >= C_WRITE_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEA) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_A + i];
end
end
// Apply incoming bytes
if (C_WEA_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEA_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Insert double bit errors:
if (C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
// Modified for Implementing CR_859399
current_contents[0] = !(current_contents[30]);
current_contents[1] = !(current_contents[62]);
/*current_contents[0] = !(current_contents[0]);
current_contents[1] = !(current_contents[1]);*/
end
end
// Insert softecc double bit errors:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1:2] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-3:0];
doublebit_error[0] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-1];
doublebit_error[1] = doublebit_error[C_WRITE_WIDTH_A+CHKBIT_WIDTH-2];
current_contents = current_contents ^ doublebit_error[C_WRITE_WIDTH_A-1:0];
end
end
// Write data to memory
if (WRITE_WIDTH_RATIO_A == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_A] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_A; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_A + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
// Store the address at which error is injected:
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
sbiterr_arr[addr] = 1;
end else begin
sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
dbiterr_arr[addr] = 1;
end else begin
dbiterr_arr[addr] = 0;
end
end
// Store the address at which softecc error is injected:
if (C_USE_SOFTECC == 1) begin
if ((C_HAS_INJECTERR == 1 && inj_sbiterr == 1'b1) ||
(C_HAS_INJECTERR == 3 && inj_sbiterr == 1'b1 && inj_dbiterr != 1'b1))
begin
softecc_sbiterr_arr[addr] = 1;
end else begin
softecc_sbiterr_arr[addr] = 0;
end
if ((C_HAS_INJECTERR == 2 || C_HAS_INJECTERR == 3) && inj_dbiterr == 1'b1) begin
softecc_dbiterr_arr[addr] = 1;
end else begin
softecc_dbiterr_arr[addr] = 0;
end
end
end
end
endtask
//**************
// write_b
//**************
task write_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg [C_WEB_WIDTH-1:0] byte_en,
input reg [C_WRITE_WIDTH_B-1:0] data);
reg [C_WRITE_WIDTH_B-1:0] current_contents;
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
// Shift the address by the ratio
address = (addr/WRITE_ADDR_B_DIV);
if (address >= C_WRITE_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Write",
C_CORENAME, addr);
end
// valid address
end else begin
// Combine w/ byte writes
if (C_USE_BYTE_WEB) begin
// Get the current memory contents
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
current_contents = memory[address];
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
current_contents[MIN_WIDTH*i+:MIN_WIDTH]
= memory[address*WRITE_WIDTH_RATIO_B + i];
end
end
// Apply incoming bytes
if (C_WEB_WIDTH == 1) begin
// Workaround for IUS 5.5 part-select issue
if (byte_en[0]) begin
current_contents = data;
end
end else begin
for (i = 0; i < C_WEB_WIDTH; i = i + 1) begin
if (byte_en[i]) begin
current_contents[BYTE_SIZE*i+:BYTE_SIZE]
= data[BYTE_SIZE*i+:BYTE_SIZE];
end
end
end
// No byte-writes, overwrite the whole word
end else begin
current_contents = data;
end
// Write data to memory
if (WRITE_WIDTH_RATIO_B == 1) begin
// Workaround for IUS 5.5 part-select issue
memory[address*WRITE_WIDTH_RATIO_B] = current_contents;
end else begin
for (i = 0; i < WRITE_WIDTH_RATIO_B; i = i + 1) begin
memory[address*WRITE_WIDTH_RATIO_B + i]
= current_contents[MIN_WIDTH*i+:MIN_WIDTH];
end
end
end
end
endtask
//**************
// read_a
//**************
task read_a
(input reg [C_ADDRA_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRA_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_a <= #FLOP_DELAY inita_val;
end else begin
// Shift the address by the ratio
address = (addr/READ_ADDR_A_DIV);
if (address >= C_READ_DEPTH_A) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for A Read",
C_CORENAME, addr);
end
memory_out_a <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_A==1) begin
memory_out_a <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_A; i = i + 1) begin
memory_out_a[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_A + i];
end
end //end READ_WIDTH_RATIO_A==1 loop
end //end valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// read_b
//**************
task read_b
(input reg [C_ADDRB_WIDTH-1:0] addr,
input reg reset);
reg [C_ADDRB_WIDTH-1:0] address;
integer i;
begin
if (reset) begin
memory_out_b <= #FLOP_DELAY initb_val;
sbiterr_in <= #FLOP_DELAY 1'b0;
dbiterr_in <= #FLOP_DELAY 1'b0;
rdaddrecc_in <= #FLOP_DELAY 0;
end else begin
// Shift the address
address = (addr/READ_ADDR_B_DIV);
if (address >= C_READ_DEPTH_B) begin
if (!C_DISABLE_WARN_BHV_RANGE) begin
$fdisplay(ADDRFILE,
"%0s WARNING: Address %0h is outside range for B Read",
C_CORENAME, addr);
end
memory_out_b <= #FLOP_DELAY 'bX;
sbiterr_in <= #FLOP_DELAY 1'bX;
dbiterr_in <= #FLOP_DELAY 1'bX;
rdaddrecc_in <= #FLOP_DELAY 'bX;
// valid address
end else begin
if (READ_WIDTH_RATIO_B==1) begin
memory_out_b <= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B];
end else begin
// Increment through the 'partial' words in the memory
for (i = 0; i < READ_WIDTH_RATIO_B; i = i + 1) begin
memory_out_b[MIN_WIDTH*i+:MIN_WIDTH]
<= #FLOP_DELAY memory[address*READ_WIDTH_RATIO_B + i];
end
end
if ((C_FAMILY_LOCALPARAM == "virtex7") && C_USE_ECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else if (C_USE_SOFTECC == 1) begin
rdaddrecc_in <= #FLOP_DELAY addr;
if (softecc_sbiterr_arr[addr] == 1) begin
sbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
sbiterr_in <= #FLOP_DELAY 1'b0;
end
if (softecc_dbiterr_arr[addr] == 1) begin
dbiterr_in <= #FLOP_DELAY 1'b1;
end else begin
dbiterr_in <= #FLOP_DELAY 1'b0;
end
end else begin
rdaddrecc_in <= #FLOP_DELAY 0;
dbiterr_in <= #FLOP_DELAY 1'b0;
sbiterr_in <= #FLOP_DELAY 1'b0;
end //end SOFTECC Loop
end //end Valid address loop
end //end reset-data assignment loops
end
endtask
//**************
// reset_a
//**************
task reset_a (input reg reset);
begin
if (reset) memory_out_a <= #FLOP_DELAY inita_val;
end
endtask
//**************
// reset_b
//**************
task reset_b (input reg reset);
begin
if (reset) memory_out_b <= #FLOP_DELAY initb_val;
end
endtask
//**************
// init_memory
//**************
task init_memory;
integer i, j, addr_step;
integer status;
reg [C_WRITE_WIDTH_A-1:0] default_data;
begin
default_data = 0;
//Display output message indicating that the behavioral model is being
//initialized
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE) $display(" Block Memory Generator module loading initial data...");
// Convert the default to hex
if (C_USE_DEFAULT_DATA) begin
if (default_data_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_DEFAULT_DATA is empty!", C_CORENAME);
$finish;
end else begin
status = $sscanf(default_data_str, "%h", default_data);
if (status == 0) begin
$fdisplay(ERRFILE, {"%0s ERROR: Unsuccessful hexadecimal read",
"from C_DEFAULT_DATA: %0s"},
C_CORENAME, C_DEFAULT_DATA);
$finish;
end
end
end
// Step by WRITE_ADDR_A_DIV through the memory via the
// Port A write interface to hit every location once
addr_step = WRITE_ADDR_A_DIV;
// 'write' to every location with default (or 0)
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, default_data, 1'b0, 1'b0);
end
// Get specialized data from the MIF file
if (C_LOAD_INIT_FILE) begin
if (init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE_NAME is empty!",
C_CORENAME);
$finish;
end else begin
initfile = $fopen(init_file_str, "r");
if (initfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE_NAME: %0s!"},
C_CORENAME, init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
for (i = 0; i < C_WRITE_DEPTH_A*addr_step; i = i + addr_step) begin
status = $fscanf(initfile, "%b", mif_data);
if (status > 0) begin
write_a(i, {C_WEA_WIDTH{1'b1}}, mif_data, 1'b0, 1'b0);
end
end
$fclose(initfile);
end //initfile
end //init_file_str
end //C_LOAD_INIT_FILE
if (C_USE_BRAM_BLOCK) begin
// Get specialized data from the MIF file
if (C_INIT_FILE != "NONE") begin
if (mem_init_file_str == "") begin
$fdisplay(ERRFILE, "%0s ERROR: C_INIT_FILE is empty!",
C_CORENAME);
$finish;
end else begin
meminitfile = $fopen(mem_init_file_str, "r");
if (meminitfile == 0) begin
$fdisplay(ERRFILE, {"%0s, ERROR: Problem opening",
"C_INIT_FILE: %0s!"},
C_CORENAME, mem_init_file_str);
$finish;
end else begin
// loop through the mif file, loading in the data
$readmemh(mem_init_file_str, memory );
for (j = 0; j < MAX_DEPTH-1 ; j = j + 1) begin
end
$fclose(meminitfile);
end //meminitfile
end //mem_init_file_str
end //C_INIT_FILE
end //C_USE_BRAM_BLOCK
//Display output message indicating that the behavioral model is done
//initializing
if (C_USE_DEFAULT_DATA || C_LOAD_INIT_FILE)
$display(" Block Memory Generator data initialization complete.");
end
endtask
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//*******************
// collision_check
//*******************
function integer collision_check (input reg [C_ADDRA_WIDTH-1:0] addr_a,
input integer iswrite_a,
input reg [C_ADDRB_WIDTH-1:0] addr_b,
input integer iswrite_b);
reg c_aw_bw, c_aw_br, c_ar_bw;
integer scaled_addra_to_waddrb_width;
integer scaled_addrb_to_waddrb_width;
integer scaled_addra_to_waddra_width;
integer scaled_addrb_to_waddra_width;
integer scaled_addra_to_raddrb_width;
integer scaled_addrb_to_raddrb_width;
integer scaled_addra_to_raddra_width;
integer scaled_addrb_to_raddra_width;
begin
c_aw_bw = 0;
c_aw_br = 0;
c_ar_bw = 0;
//If write_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_b_width. Once both are scaled to
//write_addr_b_width, compare.
scaled_addra_to_waddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_b_width));
scaled_addrb_to_waddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_b_width));
//If write_addr_a_width is smaller, scale both addresses to that width for
//comparing write_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to write_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to write_addr_a_width. Once both are scaled to
//write_addr_a_width, compare.
scaled_addra_to_waddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-write_addr_a_width));
scaled_addrb_to_waddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-write_addr_a_width));
//If read_addr_b_width is smaller, scale both addresses to that width for
//comparing write_addr_a and read_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_b_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_b_width. Once both are scaled to
//read_addr_b_width, compare.
scaled_addra_to_raddrb_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_b_width));
scaled_addrb_to_raddrb_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_b_width));
//If read_addr_a_width is smaller, scale both addresses to that width for
//comparing read_addr_a and write_addr_b; addr_a starts as C_ADDRA_WIDTH,
//scale it down to read_addr_a_width. addr_b starts as C_ADDRB_WIDTH,
//scale it down to read_addr_a_width. Once both are scaled to
//read_addr_a_width, compare.
scaled_addra_to_raddra_width = ((addr_a)/
2**(C_ADDRA_WIDTH-read_addr_a_width));
scaled_addrb_to_raddra_width = ((addr_b)/
2**(C_ADDRB_WIDTH-read_addr_a_width));
//Look for a write-write collision. In order for a write-write
//collision to exist, both ports must have a write transaction.
if (iswrite_a && iswrite_b) begin
if (write_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_bw = 1;
end else begin
c_aw_bw = 0;
end
end //width
end //iswrite_a and iswrite_b
//If the B port is reading (which means it is enabled - so could be
//a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
//to asymmetric write/read ports.
if (iswrite_a) begin
if (write_addr_a_width > read_addr_b_width) begin
if (scaled_addra_to_raddrb_width == scaled_addrb_to_raddrb_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end else begin
if (scaled_addrb_to_waddra_width == scaled_addra_to_waddra_width) begin
c_aw_br = 1;
end else begin
c_aw_br = 0;
end
end //width
end //iswrite_a
//If the A port is reading (which means it is enabled - so could be
// a TX_WRITE or TX_READ), then check for a write-read collision).
//This could happen whether or not a write-write collision exists due
// to asymmetric write/read ports.
if (iswrite_b) begin
if (read_addr_a_width > write_addr_b_width) begin
if (scaled_addra_to_waddrb_width == scaled_addrb_to_waddrb_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end else begin
if (scaled_addrb_to_raddra_width == scaled_addra_to_raddra_width) begin
c_ar_bw = 1;
end else begin
c_ar_bw = 0;
end
end //width
end //iswrite_b
collision_check = c_aw_bw | c_aw_br | c_ar_bw;
end
endfunction
//*******************************
// power on values
//*******************************
initial begin
// Load up the memory
init_memory;
// Load up the output registers and latches
if ($sscanf(inita_str, "%h", inita_val)) begin
memory_out_a = inita_val;
end else begin
memory_out_a = 0;
end
if ($sscanf(initb_str, "%h", initb_val)) begin
memory_out_b = initb_val;
end else begin
memory_out_b = 0;
end
sbiterr_in = 1'b0;
dbiterr_in = 1'b0;
rdaddrecc_in = 0;
// Determine the effective address widths for each of the 4 ports
write_addr_a_width = C_ADDRA_WIDTH - log2roundup(WRITE_ADDR_A_DIV);
read_addr_a_width = C_ADDRA_WIDTH - log2roundup(READ_ADDR_A_DIV);
write_addr_b_width = C_ADDRB_WIDTH - log2roundup(WRITE_ADDR_B_DIV);
read_addr_b_width = C_ADDRB_WIDTH - log2roundup(READ_ADDR_B_DIV);
$display("Block Memory Generator module %m is using a behavioral model for simulation which will not precisely model memory collision behavior.");
end
//***************************************************************************
// These are the main blocks which schedule read and write operations
// Note that the reset priority feature at the latch stage is only supported
// for Spartan-6. For other families, the default priority at the latch stage
// is "CE"
//***************************************************************************
// Synchronous clocks: schedule port operations with respect to
// both write operating modes
generate
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_wf_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_rf_wf
always @(posedge CLKA) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "WRITE_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_wf_rf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else
if(C_COMMON_CLK && (C_WRITE_MODE_A == "READ_FIRST") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_rf_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="WRITE_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_wf_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="READ_FIRST") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_rf_nc
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"WRITE_FIRST")) begin : com_clk_sched_nc_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"READ_FIRST")) begin : com_clk_sched_nc_rf
always @(posedge CLKA) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if(C_COMMON_CLK && (C_WRITE_MODE_A =="NO_CHANGE") && (C_WRITE_MODE_B ==
"NO_CHANGE")) begin : com_clk_sched_nc_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
else if(C_COMMON_CLK) begin: com_clk_sched_default
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
endgenerate
// Asynchronous clocks: port operation is independent
generate
if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "WRITE_FIRST")) begin : async_clk_sched_clka_wf
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "READ_FIRST")) begin : async_clk_sched_clka_rf
always @(posedge CLKA) begin
//Read A
if (rea_i) read_a(ADDRA, reseta_i);
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
end
end
else if((!C_COMMON_CLK) && (C_WRITE_MODE_A == "NO_CHANGE")) begin : async_clk_sched_clka_nc
always @(posedge CLKA) begin
//Write A
if (wea_i) write_a(ADDRA, wea_i, DINA, INJECTSBITERR, INJECTDBITERR);
//Read A
if (rea_i && (!wea_i || reseta_i)) read_a(ADDRA, reseta_i);
end
end
endgenerate
generate
if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "WRITE_FIRST")) begin: async_clk_sched_clkb_wf
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "READ_FIRST")) begin: async_clk_sched_clkb_rf
always @(posedge CLKB) begin
//Read B
if (reb_i) read_b(ADDRB, resetb_i);
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
end
end
else if ((!C_COMMON_CLK) && (C_WRITE_MODE_B == "NO_CHANGE")) begin: async_clk_sched_clkb_nc
always @(posedge CLKB) begin
//Write B
if (web_i) write_b(ADDRB, web_i, DINB);
//Read B
if (reb_i && (!web_i || resetb_i)) read_b(ADDRB, resetb_i);
end
end
endgenerate
//***************************************************************
// Instantiate the variable depth output register stage module
//***************************************************************
// Port A
assign rsta_outp_stage = RSTA & (~SLEEP);
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTA),
.C_RSTRAM (C_RSTRAM_A),
.C_RST_PRIORITY (C_RST_PRIORITY_A),
.C_INIT_VAL (C_INITA_VAL),
.C_HAS_EN (C_HAS_ENA),
.C_HAS_REGCE (C_HAS_REGCEA),
.C_DATA_WIDTH (C_READ_WIDTH_A),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_A),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_A),
.C_EN_ECC_PIPE (0),
.FLOP_DELAY (FLOP_DELAY))
reg_a
(.CLK (CLKA),
.RST (rsta_outp_stage),//(RSTA),
.EN (ENA),
.REGCE (REGCEA),
.DIN_I (memory_out_a),
.DOUT (DOUTA),
.SBITERR_IN_I (1'b0),
.DBITERR_IN_I (1'b0),
.SBITERR (),
.DBITERR (),
.RDADDRECC_IN_I ({C_ADDRB_WIDTH{1'b0}}),
.ECCPIPECE (1'b0),
.RDADDRECC ()
);
assign rstb_outp_stage = RSTB & (~SLEEP);
// Port B
blk_mem_gen_v8_3_5_output_stage
#(.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_RST_TYPE ("SYNC"),
.C_HAS_RST (C_HAS_RSTB),
.C_RSTRAM (C_RSTRAM_B),
.C_RST_PRIORITY (C_RST_PRIORITY_B),
.C_INIT_VAL (C_INITB_VAL),
.C_HAS_EN (C_HAS_ENB),
.C_HAS_REGCE (C_HAS_REGCEB),
.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.NUM_STAGES (NUM_OUTPUT_STAGES_B),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.FLOP_DELAY (FLOP_DELAY))
reg_b
(.CLK (CLKB),
.RST (rstb_outp_stage),//(RSTB),
.EN (ENB),
.REGCE (REGCEB),
.DIN_I (memory_out_b),
.DOUT (dout_i),
.SBITERR_IN_I (sbiterr_in),
.DBITERR_IN_I (dbiterr_in),
.SBITERR (sbiterr_i),
.DBITERR (dbiterr_i),
.RDADDRECC_IN_I (rdaddrecc_in),
.ECCPIPECE (ECCPIPECE),
.RDADDRECC (rdaddrecc_i)
);
//***************************************************************
// Instantiate the Input and Output register stages
//***************************************************************
blk_mem_gen_v8_3_5_softecc_output_reg_stage
#(.C_DATA_WIDTH (C_READ_WIDTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_USE_SOFTECC (C_USE_SOFTECC),
.FLOP_DELAY (FLOP_DELAY))
has_softecc_output_reg_stage
(.CLK (CLKB),
.DIN (dout_i),
.DOUT (DOUTB),
.SBITERR_IN (sbiterr_i),
.DBITERR_IN (dbiterr_i),
.SBITERR (sbiterr_sdp),
.DBITERR (dbiterr_sdp),
.RDADDRECC_IN (rdaddrecc_i),
.RDADDRECC (rdaddrecc_sdp)
);
//****************************************************
// Synchronous collision checks
//****************************************************
// CR 780544 : To make verilog model's collison warnings in consistant with
// vhdl model, the non-blocking assignments are replaced with blocking
// assignments.
generate if (!C_DISABLE_WARN_BHV_COLL && C_COMMON_CLK) begin : sync_coll
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision = 0;
end
end else begin
is_collision = 0;
end
// If the write port is in READ_FIRST mode, there is no collision
if (C_WRITE_MODE_A=="READ_FIRST" && wea_i && !web_i) begin
is_collision = 0;
end
if (C_WRITE_MODE_B=="READ_FIRST" && web_i && !wea_i) begin
is_collision = 0;
end
// Only flag if one of the accesses is a write
if (is_collision && (wea_i || web_i)) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B %0s address: %0h\n",
wea_i ? "write" : "read", ADDRA,
web_i ? "write" : "read", ADDRB);
end
end
//****************************************************
// Asynchronous collision checks
//****************************************************
end else if (!C_DISABLE_WARN_BHV_COLL && !C_COMMON_CLK) begin : async_coll
// Delay A and B addresses in order to mimic setup/hold times
wire [C_ADDRA_WIDTH-1:0] #COLL_DELAY addra_delay = ADDRA;
wire [0:0] #COLL_DELAY wea_delay = wea_i;
wire #COLL_DELAY ena_delay = ena_i;
wire [C_ADDRB_WIDTH-1:0] #COLL_DELAY addrb_delay = ADDRB;
wire [0:0] #COLL_DELAY web_delay = web_i;
wire #COLL_DELAY enb_delay = enb_i;
// Do the checks w/rt A
always @(posedge CLKA) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_a = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_a = 0;
end
end else begin
is_collision_a = 0;
end
if (ena_i && enb_delay) begin
if(wea_i || web_delay) begin
is_collision_delay_a = collision_check(ADDRA, wea_i, addrb_delay,
web_delay);
end else begin
is_collision_delay_a = 0;
end
end else begin
is_collision_delay_a = 0;
end
// Only flag if B access is a write
if (is_collision_a && web_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, ADDRB);
end else if (is_collision_delay_a && web_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A %0s address: %0h, B write address: %0h\n",
wea_i ? "write" : "read", ADDRA, addrb_delay);
end
end
// Do the checks w/rt B
always @(posedge CLKB) begin
// Possible collision if both are enabled and the addresses match
if (ena_i && enb_i) begin
if (wea_i || web_i) begin
is_collision_b = collision_check(ADDRA, wea_i, ADDRB, web_i);
end else begin
is_collision_b = 0;
end
end else begin
is_collision_b = 0;
end
if (ena_delay && enb_i) begin
if (wea_delay || web_i) begin
is_collision_delay_b = collision_check(addra_delay, wea_delay, ADDRB,
web_i);
end else begin
is_collision_delay_b = 0;
end
end else begin
is_collision_delay_b = 0;
end
// Only flag if A access is a write
if (is_collision_b && wea_i) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
ADDRA, web_i ? "write" : "read", ADDRB);
end else if (is_collision_delay_b && wea_delay) begin
$fwrite(COLLFILE, "%0s collision detected at time: %0d, ",
C_CORENAME, $time);
$fwrite(COLLFILE, "A write address: %0h, B %s address: %0h\n",
addra_delay, web_i ? "write" : "read", ADDRB);
end
end
end
endgenerate
endmodule
//*****************************************************************************
// Top module wraps Input register and Memory module
//
// This module is the top-level behavioral model and this implements the memory
// module and the input registers
//*****************************************************************************
module blk_mem_gen_v8_3_5
#(parameter C_CORENAME = "blk_mem_gen_v8_3_5",
parameter C_FAMILY = "virtex7",
parameter C_XDEVICEFAMILY = "virtex7",
parameter C_ELABORATION_DIR = "",
parameter C_INTERFACE_TYPE = 0,
parameter C_USE_BRAM_BLOCK = 0,
parameter C_CTRL_ECC_ALGO = "NONE",
parameter C_ENABLE_32BIT_ADDRESS = 0,
parameter C_AXI_TYPE = 0,
parameter C_AXI_SLAVE_TYPE = 0,
parameter C_HAS_AXI_ID = 0,
parameter C_AXI_ID_WIDTH = 4,
parameter C_MEM_TYPE = 2,
parameter C_BYTE_SIZE = 9,
parameter C_ALGORITHM = 1,
parameter C_PRIM_TYPE = 3,
parameter C_LOAD_INIT_FILE = 0,
parameter C_INIT_FILE_NAME = "",
parameter C_INIT_FILE = "",
parameter C_USE_DEFAULT_DATA = 0,
parameter C_DEFAULT_DATA = "0",
//parameter C_RST_TYPE = "SYNC",
parameter C_HAS_RSTA = 0,
parameter C_RST_PRIORITY_A = "CE",
parameter C_RSTRAM_A = 0,
parameter C_INITA_VAL = "0",
parameter C_HAS_ENA = 1,
parameter C_HAS_REGCEA = 0,
parameter C_USE_BYTE_WEA = 0,
parameter C_WEA_WIDTH = 1,
parameter C_WRITE_MODE_A = "WRITE_FIRST",
parameter C_WRITE_WIDTH_A = 32,
parameter C_READ_WIDTH_A = 32,
parameter C_WRITE_DEPTH_A = 64,
parameter C_READ_DEPTH_A = 64,
parameter C_ADDRA_WIDTH = 5,
parameter C_HAS_RSTB = 0,
parameter C_RST_PRIORITY_B = "CE",
parameter C_RSTRAM_B = 0,
parameter C_INITB_VAL = "",
parameter C_HAS_ENB = 1,
parameter C_HAS_REGCEB = 0,
parameter C_USE_BYTE_WEB = 0,
parameter C_WEB_WIDTH = 1,
parameter C_WRITE_MODE_B = "WRITE_FIRST",
parameter C_WRITE_WIDTH_B = 32,
parameter C_READ_WIDTH_B = 32,
parameter C_WRITE_DEPTH_B = 64,
parameter C_READ_DEPTH_B = 64,
parameter C_ADDRB_WIDTH = 5,
parameter C_HAS_MEM_OUTPUT_REGS_A = 0,
parameter C_HAS_MEM_OUTPUT_REGS_B = 0,
parameter C_HAS_MUX_OUTPUT_REGS_A = 0,
parameter C_HAS_MUX_OUTPUT_REGS_B = 0,
parameter C_HAS_SOFTECC_INPUT_REGS_A = 0,
parameter C_HAS_SOFTECC_OUTPUT_REGS_B= 0,
parameter C_MUX_PIPELINE_STAGES = 0,
parameter C_USE_SOFTECC = 0,
parameter C_USE_ECC = 0,
parameter C_EN_ECC_PIPE = 0,
parameter C_HAS_INJECTERR = 0,
parameter C_SIM_COLLISION_CHECK = "NONE",
parameter C_COMMON_CLK = 1,
parameter C_DISABLE_WARN_BHV_COLL = 0,
parameter C_EN_SLEEP_PIN = 0,
parameter C_USE_URAM = 0,
parameter C_EN_RDADDRA_CHG = 0,
parameter C_EN_RDADDRB_CHG = 0,
parameter C_EN_DEEPSLEEP_PIN = 0,
parameter C_EN_SHUTDOWN_PIN = 0,
parameter C_EN_SAFETY_CKT = 0,
parameter C_COUNT_36K_BRAM = "",
parameter C_COUNT_18K_BRAM = "",
parameter C_EST_POWER_SUMMARY = "",
parameter C_DISABLE_WARN_BHV_RANGE = 0
)
(input clka,
input rsta,
input ena,
input regcea,
input [C_WEA_WIDTH-1:0] wea,
input [C_ADDRA_WIDTH-1:0] addra,
input [C_WRITE_WIDTH_A-1:0] dina,
output [C_READ_WIDTH_A-1:0] douta,
input clkb,
input rstb,
input enb,
input regceb,
input [C_WEB_WIDTH-1:0] web,
input [C_ADDRB_WIDTH-1:0] addrb,
input [C_WRITE_WIDTH_B-1:0] dinb,
output [C_READ_WIDTH_B-1:0] doutb,
input injectsbiterr,
input injectdbiterr,
output sbiterr,
output dbiterr,
output [C_ADDRB_WIDTH-1:0] rdaddrecc,
input eccpipece,
input sleep,
input deepsleep,
input shutdown,
output rsta_busy,
output rstb_busy,
//AXI BMG Input and Output Port Declarations
//AXI Global Signals
input s_aclk,
input s_aresetn,
//AXI Full/lite slave write (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_awid,
input [31:0] s_axi_awaddr,
input [7:0] s_axi_awlen,
input [2:0] s_axi_awsize,
input [1:0] s_axi_awburst,
input s_axi_awvalid,
output s_axi_awready,
input [C_WRITE_WIDTH_A-1:0] s_axi_wdata,
input [C_WEA_WIDTH-1:0] s_axi_wstrb,
input s_axi_wlast,
input s_axi_wvalid,
output s_axi_wready,
output [C_AXI_ID_WIDTH-1:0] s_axi_bid,
output [1:0] s_axi_bresp,
output s_axi_bvalid,
input s_axi_bready,
//AXI Full/lite slave read (write side)
input [C_AXI_ID_WIDTH-1:0] s_axi_arid,
input [31:0] s_axi_araddr,
input [7:0] s_axi_arlen,
input [2:0] s_axi_arsize,
input [1:0] s_axi_arburst,
input s_axi_arvalid,
output s_axi_arready,
output [C_AXI_ID_WIDTH-1:0] s_axi_rid,
output [C_WRITE_WIDTH_B-1:0] s_axi_rdata,
output [1:0] s_axi_rresp,
output s_axi_rlast,
output s_axi_rvalid,
input s_axi_rready,
//AXI Full/lite sideband signals
input s_axi_injectsbiterr,
input s_axi_injectdbiterr,
output s_axi_sbiterr,
output s_axi_dbiterr,
output [C_ADDRB_WIDTH-1:0] s_axi_rdaddrecc
);
//******************************
// Port and Generic Definitions
//******************************
//////////////////////////////////////////////////////////////////////////
// Generic Definitions
//////////////////////////////////////////////////////////////////////////
// C_CORENAME : Instance name of the Block Memory Generator core
// C_FAMILY,C_XDEVICEFAMILY: Designates architecture targeted. The following
// options are available - "spartan3", "spartan6",
// "virtex4", "virtex5", "virtex6" and "virtex6l".
// C_MEM_TYPE : Designates memory type.
// It can be
// 0 - Single Port Memory
// 1 - Simple Dual Port Memory
// 2 - True Dual Port Memory
// 3 - Single Port Read Only Memory
// 4 - Dual Port Read Only Memory
// C_BYTE_SIZE : Size of a byte (8 or 9 bits)
// C_ALGORITHM : Designates the algorithm method used
// for constructing the memory.
// It can be Fixed_Primitives, Minimum_Area or
// Low_Power
// C_PRIM_TYPE : Designates the user selected primitive used to
// construct the memory.
//
// C_LOAD_INIT_FILE : Designates the use of an initialization file to
// initialize memory contents.
// C_INIT_FILE_NAME : Memory initialization file name.
// C_USE_DEFAULT_DATA : Designates whether to fill remaining
// initialization space with default data
// C_DEFAULT_DATA : Default value of all memory locations
// not initialized by the memory
// initialization file.
// C_RST_TYPE : Type of reset - Synchronous or Asynchronous
// C_HAS_RSTA : Determines the presence of the RSTA port
// C_RST_PRIORITY_A : Determines the priority between CE and SR for
// Port A.
// C_RSTRAM_A : Determines if special reset behavior is used for
// Port A
// C_INITA_VAL : The initialization value for Port A
// C_HAS_ENA : Determines the presence of the ENA port
// C_HAS_REGCEA : Determines the presence of the REGCEA port
// C_USE_BYTE_WEA : Determines if the Byte Write is used or not.
// C_WEA_WIDTH : The width of the WEA port
// C_WRITE_MODE_A : Configurable write mode for Port A. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_A : Memory write width for Port A.
// C_READ_WIDTH_A : Memory read width for Port A.
// C_WRITE_DEPTH_A : Memory write depth for Port A.
// C_READ_DEPTH_A : Memory read depth for Port A.
// C_ADDRA_WIDTH : Width of the ADDRA input port
// C_HAS_RSTB : Determines the presence of the RSTB port
// C_RST_PRIORITY_B : Determines the priority between CE and SR for
// Port B.
// C_RSTRAM_B : Determines if special reset behavior is used for
// Port B
// C_INITB_VAL : The initialization value for Port B
// C_HAS_ENB : Determines the presence of the ENB port
// C_HAS_REGCEB : Determines the presence of the REGCEB port
// C_USE_BYTE_WEB : Determines if the Byte Write is used or not.
// C_WEB_WIDTH : The width of the WEB port
// C_WRITE_MODE_B : Configurable write mode for Port B. It can be
// WRITE_FIRST, READ_FIRST or NO_CHANGE.
// C_WRITE_WIDTH_B : Memory write width for Port B.
// C_READ_WIDTH_B : Memory read width for Port B.
// C_WRITE_DEPTH_B : Memory write depth for Port B.
// C_READ_DEPTH_B : Memory read depth for Port B.
// C_ADDRB_WIDTH : Width of the ADDRB input port
// C_HAS_MEM_OUTPUT_REGS_A : Designates the use of a register at the output
// of the RAM primitive for Port A.
// C_HAS_MEM_OUTPUT_REGS_B : Designates the use of a register at the output
// of the RAM primitive for Port B.
// C_HAS_MUX_OUTPUT_REGS_A : Designates the use of a register at the output
// of the MUX for Port A.
// C_HAS_MUX_OUTPUT_REGS_B : Designates the use of a register at the output
// of the MUX for Port B.
// C_HAS_SOFTECC_INPUT_REGS_A :
// C_HAS_SOFTECC_OUTPUT_REGS_B :
// C_MUX_PIPELINE_STAGES : Designates the number of pipeline stages in
// between the muxes.
// C_USE_SOFTECC : Determines if the Soft ECC feature is used or
// not. Only applicable Spartan-6
// C_USE_ECC : Determines if the ECC feature is used or
// not. Only applicable for V5 and V6
// C_HAS_INJECTERR : Determines if the error injection pins
// are present or not. If the ECC feature
// is not used, this value is defaulted to
// 0, else the following are the allowed
// values:
// 0 : No INJECTSBITERR or INJECTDBITERR pins
// 1 : Only INJECTSBITERR pin exists
// 2 : Only INJECTDBITERR pin exists
// 3 : Both INJECTSBITERR and INJECTDBITERR pins exist
// C_SIM_COLLISION_CHECK : Controls the disabling of Unisim model collision
// warnings. It can be "ALL", "NONE",
// "Warnings_Only" or "Generate_X_Only".
// C_COMMON_CLK : Determins if the core has a single CLK input.
// C_DISABLE_WARN_BHV_COLL : Controls the Behavioral Model Collision warnings
// C_DISABLE_WARN_BHV_RANGE: Controls the Behavioral Model Out of Range
// warnings
//////////////////////////////////////////////////////////////////////////
// Port Definitions
//////////////////////////////////////////////////////////////////////////
// CLKA : Clock to synchronize all read and write operations of Port A.
// RSTA : Reset input to reset memory outputs to a user-defined
// reset state for Port A.
// ENA : Enable all read and write operations of Port A.
// REGCEA : Register Clock Enable to control each pipeline output
// register stages for Port A.
// WEA : Write Enable to enable all write operations of Port A.
// ADDRA : Address of Port A.
// DINA : Data input of Port A.
// DOUTA : Data output of Port A.
// CLKB : Clock to synchronize all read and write operations of Port B.
// RSTB : Reset input to reset memory outputs to a user-defined
// reset state for Port B.
// ENB : Enable all read and write operations of Port B.
// REGCEB : Register Clock Enable to control each pipeline output
// register stages for Port B.
// WEB : Write Enable to enable all write operations of Port B.
// ADDRB : Address of Port B.
// DINB : Data input of Port B.
// DOUTB : Data output of Port B.
// INJECTSBITERR : Single Bit ECC Error Injection Pin.
// INJECTDBITERR : Double Bit ECC Error Injection Pin.
// SBITERR : Output signal indicating that a Single Bit ECC Error has been
// detected and corrected.
// DBITERR : Output signal indicating that a Double Bit ECC Error has been
// detected.
// RDADDRECC : Read Address Output signal indicating address at which an
// ECC error has occurred.
//////////////////////////////////////////////////////////////////////////
wire SBITERR;
wire DBITERR;
wire S_AXI_AWREADY;
wire S_AXI_WREADY;
wire S_AXI_BVALID;
wire S_AXI_ARREADY;
wire S_AXI_RLAST;
wire S_AXI_RVALID;
wire S_AXI_SBITERR;
wire S_AXI_DBITERR;
wire [C_WEA_WIDTH-1:0] WEA = wea;
wire [C_ADDRA_WIDTH-1:0] ADDRA = addra;
wire [C_WRITE_WIDTH_A-1:0] DINA = dina;
wire [C_READ_WIDTH_A-1:0] DOUTA;
wire [C_WEB_WIDTH-1:0] WEB = web;
wire [C_ADDRB_WIDTH-1:0] ADDRB = addrb;
wire [C_WRITE_WIDTH_B-1:0] DINB = dinb;
wire [C_READ_WIDTH_B-1:0] DOUTB;
wire [C_ADDRB_WIDTH-1:0] RDADDRECC;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_AWID = s_axi_awid;
wire [31:0] S_AXI_AWADDR = s_axi_awaddr;
wire [7:0] S_AXI_AWLEN = s_axi_awlen;
wire [2:0] S_AXI_AWSIZE = s_axi_awsize;
wire [1:0] S_AXI_AWBURST = s_axi_awburst;
wire [C_WRITE_WIDTH_A-1:0] S_AXI_WDATA = s_axi_wdata;
wire [C_WEA_WIDTH-1:0] S_AXI_WSTRB = s_axi_wstrb;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_BID;
wire [1:0] S_AXI_BRESP;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_ARID = s_axi_arid;
wire [31:0] S_AXI_ARADDR = s_axi_araddr;
wire [7:0] S_AXI_ARLEN = s_axi_arlen;
wire [2:0] S_AXI_ARSIZE = s_axi_arsize;
wire [1:0] S_AXI_ARBURST = s_axi_arburst;
wire [C_AXI_ID_WIDTH-1:0] S_AXI_RID;
wire [C_WRITE_WIDTH_B-1:0] S_AXI_RDATA;
wire [1:0] S_AXI_RRESP;
wire [C_ADDRB_WIDTH-1:0] S_AXI_RDADDRECC;
// Added to fix the simulation warning #CR731605
wire [C_WEB_WIDTH-1:0] WEB_parameterized = 0;
wire ECCPIPECE;
wire SLEEP;
reg RSTA_BUSY = 0;
reg RSTB_BUSY = 0;
// Declaration of internal signals to avoid warnings #927399
wire CLKA;
wire RSTA;
wire ENA;
wire REGCEA;
wire CLKB;
wire RSTB;
wire ENB;
wire REGCEB;
wire INJECTSBITERR;
wire INJECTDBITERR;
wire S_ACLK;
wire S_ARESETN;
wire S_AXI_AWVALID;
wire S_AXI_WLAST;
wire S_AXI_WVALID;
wire S_AXI_BREADY;
wire S_AXI_ARVALID;
wire S_AXI_RREADY;
wire S_AXI_INJECTSBITERR;
wire S_AXI_INJECTDBITERR;
assign CLKA = clka;
assign RSTA = rsta;
assign ENA = ena;
assign REGCEA = regcea;
assign CLKB = clkb;
assign RSTB = rstb;
assign ENB = enb;
assign REGCEB = regceb;
assign INJECTSBITERR = injectsbiterr;
assign INJECTDBITERR = injectdbiterr;
assign ECCPIPECE = eccpipece;
assign SLEEP = sleep;
assign sbiterr = SBITERR;
assign dbiterr = DBITERR;
assign S_ACLK = s_aclk;
assign S_ARESETN = s_aresetn;
assign S_AXI_AWVALID = s_axi_awvalid;
assign s_axi_awready = S_AXI_AWREADY;
assign S_AXI_WLAST = s_axi_wlast;
assign S_AXI_WVALID = s_axi_wvalid;
assign s_axi_wready = S_AXI_WREADY;
assign s_axi_bvalid = S_AXI_BVALID;
assign S_AXI_BREADY = s_axi_bready;
assign S_AXI_ARVALID = s_axi_arvalid;
assign s_axi_arready = S_AXI_ARREADY;
assign s_axi_rlast = S_AXI_RLAST;
assign s_axi_rvalid = S_AXI_RVALID;
assign S_AXI_RREADY = s_axi_rready;
assign S_AXI_INJECTSBITERR = s_axi_injectsbiterr;
assign S_AXI_INJECTDBITERR = s_axi_injectdbiterr;
assign s_axi_sbiterr = S_AXI_SBITERR;
assign s_axi_dbiterr = S_AXI_DBITERR;
assign rsta_busy = RSTA_BUSY;
assign rstb_busy = RSTB_BUSY;
assign doutb = DOUTB;
assign douta = DOUTA;
assign rdaddrecc = RDADDRECC;
assign s_axi_bid = S_AXI_BID;
assign s_axi_bresp = S_AXI_BRESP;
assign s_axi_rid = S_AXI_RID;
assign s_axi_rdata = S_AXI_RDATA;
assign s_axi_rresp = S_AXI_RRESP;
assign s_axi_rdaddrecc = S_AXI_RDADDRECC;
localparam FLOP_DELAY = 100; // 100 ps
reg injectsbiterr_in;
reg injectdbiterr_in;
reg rsta_in;
reg ena_in;
reg regcea_in;
reg [C_WEA_WIDTH-1:0] wea_in;
reg [C_ADDRA_WIDTH-1:0] addra_in;
reg [C_WRITE_WIDTH_A-1:0] dina_in;
wire [C_ADDRA_WIDTH-1:0] s_axi_awaddr_out_c;
wire [C_ADDRB_WIDTH-1:0] s_axi_araddr_out_c;
wire s_axi_wr_en_c;
wire s_axi_rd_en_c;
wire s_aresetn_a_c;
wire [7:0] s_axi_arlen_c ;
wire [C_AXI_ID_WIDTH-1 : 0] s_axi_rid_c;
wire [C_WRITE_WIDTH_B-1 : 0] s_axi_rdata_c;
wire [1:0] s_axi_rresp_c;
wire s_axi_rlast_c;
wire s_axi_rvalid_c;
wire s_axi_rready_c;
wire regceb_c;
localparam C_AXI_PAYLOAD = (C_HAS_MUX_OUTPUT_REGS_B == 1)?C_WRITE_WIDTH_B+C_AXI_ID_WIDTH+3:C_AXI_ID_WIDTH+3;
wire [C_AXI_PAYLOAD-1 : 0] s_axi_payload_c;
wire [C_AXI_PAYLOAD-1 : 0] m_axi_payload_c;
// Safety logic related signals
reg [4:0] RSTA_SHFT_REG = 0;
reg POR_A = 0;
reg [4:0] RSTB_SHFT_REG = 0;
reg POR_B = 0;
reg ENA_dly = 0;
reg ENA_dly_D = 0;
reg ENB_dly = 0;
reg ENB_dly_D = 0;
wire RSTA_I_SAFE;
wire RSTB_I_SAFE;
wire ENA_I_SAFE;
wire ENB_I_SAFE;
reg ram_rstram_a_busy = 0;
reg ram_rstreg_a_busy = 0;
reg ram_rstram_b_busy = 0;
reg ram_rstreg_b_busy = 0;
reg ENA_dly_reg = 0;
reg ENB_dly_reg = 0;
reg ENA_dly_reg_D = 0;
reg ENB_dly_reg_D = 0;
//**************
// log2roundup
//**************
function integer log2roundup (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
if (data_value > 1) begin
for(cnt=1 ; cnt < data_value ; cnt = cnt * 2) begin
width = width + 1;
end //loop
end //if
log2roundup = width;
end //log2roundup
endfunction
//**************
// log2int
//**************
function integer log2int (input integer data_value);
integer width;
integer cnt;
begin
width = 0;
cnt= data_value;
for(cnt=data_value ; cnt >1 ; cnt = cnt / 2) begin
width = width + 1;
end //loop
log2int = width;
end //log2int
endfunction
//**************************************************************************
// FUNCTION : divroundup
// Returns the ceiling value of the division
// Data_value - the quantity to be divided, dividend
// Divisor - the value to divide the data_value by
//**************************************************************************
function integer divroundup (input integer data_value,input integer divisor);
integer div;
begin
div = data_value/divisor;
if ((data_value % divisor) != 0) begin
div = div+1;
end //if
divroundup = div;
end //if
endfunction
localparam AXI_FULL_MEMORY_SLAVE = ((C_AXI_SLAVE_TYPE == 0 && C_AXI_TYPE == 1)?1:0);
localparam C_AXI_ADDR_WIDTH_MSB = C_ADDRA_WIDTH+log2roundup(C_WRITE_WIDTH_A/8);
localparam C_AXI_ADDR_WIDTH = C_AXI_ADDR_WIDTH_MSB;
//Data Width Number of LSB address bits to be discarded
//1 to 16 1
//17 to 32 2
//33 to 64 3
//65 to 128 4
//129 to 256 5
//257 to 512 6
//513 to 1024 7
// The following two constants determine this.
localparam LOWER_BOUND_VAL = (log2roundup(divroundup(C_WRITE_WIDTH_A,8) == 0))?0:(log2roundup(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_AXI_ADDR_WIDTH_LSB = ((AXI_FULL_MEMORY_SLAVE == 1)?0:LOWER_BOUND_VAL);
localparam C_AXI_OS_WR = 2;
//***********************************************
// INPUT REGISTERS.
//***********************************************
generate if (C_HAS_SOFTECC_INPUT_REGS_A==0) begin : no_softecc_input_reg_stage
always @* begin
injectsbiterr_in = INJECTSBITERR;
injectdbiterr_in = INJECTDBITERR;
rsta_in = RSTA;
ena_in = ENA;
regcea_in = REGCEA;
wea_in = WEA;
addra_in = ADDRA;
dina_in = DINA;
end //end always
end //end no_softecc_input_reg_stage
endgenerate
generate if (C_HAS_SOFTECC_INPUT_REGS_A==1) begin : has_softecc_input_reg_stage
always @(posedge CLKA) begin
injectsbiterr_in <= #FLOP_DELAY INJECTSBITERR;
injectdbiterr_in <= #FLOP_DELAY INJECTDBITERR;
rsta_in <= #FLOP_DELAY RSTA;
ena_in <= #FLOP_DELAY ENA;
regcea_in <= #FLOP_DELAY REGCEA;
wea_in <= #FLOP_DELAY WEA;
addra_in <= #FLOP_DELAY ADDRA;
dina_in <= #FLOP_DELAY DINA;
end //end always
end //end input_reg_stages generate statement
endgenerate
//**************************************************************************
// NO SAFETY LOGIC
//**************************************************************************
generate
if (C_EN_SAFETY_CKT == 0) begin : NO_SAFETY_CKT_GEN
assign ENA_I_SAFE = ena_in;
assign ENB_I_SAFE = ENB;
assign RSTA_I_SAFE = rsta_in;
assign RSTB_I_SAFE = RSTB;
end
endgenerate
//***************************************************************************
// SAFETY LOGIC
// Power-ON Reset Generation
//***************************************************************************
generate
if (C_EN_SAFETY_CKT == 1) begin
always @(posedge clka) RSTA_SHFT_REG <= #FLOP_DELAY {RSTA_SHFT_REG[3:0],1'b1} ;
always @(posedge clka) POR_A <= #FLOP_DELAY RSTA_SHFT_REG[4] ^ RSTA_SHFT_REG[0];
always @(posedge clkb) RSTB_SHFT_REG <= #FLOP_DELAY {RSTB_SHFT_REG[3:0],1'b1} ;
always @(posedge clkb) POR_B <= #FLOP_DELAY RSTB_SHFT_REG[4] ^ RSTB_SHFT_REG[0];
assign RSTA_I_SAFE = rsta_in | POR_A;
assign RSTB_I_SAFE = (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) ? 1'b0 : (RSTB | POR_B);
end
endgenerate
//-----------------------------------------------------------------------------
// -- RSTA/B_BUSY Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && (C_EN_SAFETY_CKT == 1)) begin : RSTA_BUSY_NO_REG
always @(*) ram_rstram_a_busy = RSTA_I_SAFE | ENA_dly | ENA_dly_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstram_a_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0 && C_EN_SAFETY_CKT == 1) begin : RSTA_BUSY_WITH_REG
always @(*) ram_rstreg_a_busy = RSTA_I_SAFE | ENA_dly_reg | ENA_dly_reg_D;
always @(posedge clka) RSTA_BUSY <= #FLOP_DELAY ram_rstreg_a_busy;
end
endgenerate
generate
if ( (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) && C_EN_SAFETY_CKT == 1) begin : SPRAM_RST_BUSY
always @(*) RSTB_BUSY = 1'b0;
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && (C_MEM_TYPE != 0 && C_MEM_TYPE != 3) && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_NO_REG
always @(*) ram_rstram_b_busy = RSTB_I_SAFE | ENB_dly | ENB_dly_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstram_b_busy;
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : RSTB_BUSY_WITH_REG
always @(*) ram_rstreg_b_busy = RSTB_I_SAFE | ENB_dly_reg | ENB_dly_reg_D;
always @(posedge clkb) RSTB_BUSY <= #FLOP_DELAY ram_rstreg_b_busy;
end
endgenerate
//-----------------------------------------------------------------------------
// -- ENA/ENB Generation
//-----------------------------------------------------------------------------
generate
if ((C_HAS_MEM_OUTPUT_REGS_A==0 || (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==1)) && C_EN_SAFETY_CKT == 1) begin : ENA_NO_REG
always @(posedge clka) begin
ENA_dly <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_D <= #FLOP_DELAY ENA_dly;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_D | ena_in);
end
endgenerate
generate
if ( (C_HAS_MEM_OUTPUT_REGS_A==1 && C_RSTRAM_A==0) && C_EN_SAFETY_CKT == 1) begin : ENA_WITH_REG
always @(posedge clka) begin
ENA_dly_reg <= #FLOP_DELAY RSTA_I_SAFE;
ENA_dly_reg_D <= #FLOP_DELAY ENA_dly_reg;
end
assign ENA_I_SAFE = (C_HAS_ENA == 0)? 1'b1 : (ENA_dly_reg_D | ena_in);
end
endgenerate
generate
if (C_MEM_TYPE == 0 || C_MEM_TYPE == 3) begin : SPRAM_ENB
assign ENB_I_SAFE = 1'b0;
end
endgenerate
generate
if ((C_HAS_MEM_OUTPUT_REGS_B==0 || (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==1)) && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1) begin : ENB_NO_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_D <= #FLOP_DELAY ENB_dly;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_D | ENB);
end
endgenerate
generate
if (C_HAS_MEM_OUTPUT_REGS_B==1 && C_RSTRAM_B==0 && C_MEM_TYPE != 0 && C_MEM_TYPE != 3 && C_EN_SAFETY_CKT == 1)begin : ENB_WITH_REG
always @(posedge clkb) begin : PROC_ENB_GEN
ENB_dly_reg <= #FLOP_DELAY RSTB_I_SAFE;
ENB_dly_reg_D <= #FLOP_DELAY ENB_dly_reg;
end
assign ENB_I_SAFE = (C_HAS_ENB == 0)? 1'b1 : (ENB_dly_reg_D | ENB);
end
endgenerate
generate if ((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 0)) begin : native_mem_module
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_ALGORITHM (C_ALGORITHM),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
generate if((C_INTERFACE_TYPE == 0) && (C_ENABLE_32BIT_ADDRESS == 1)) begin : native_mem_mapped_module
localparam C_ADDRA_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_A);
localparam C_ADDRB_WIDTH_ACTUAL = log2roundup(C_WRITE_DEPTH_B);
localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_A/8);
localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2int(C_WRITE_WIDTH_B/8);
// localparam C_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_A/8);
// localparam C_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_ACTUAL+log2roundup(C_WRITE_WIDTH_B/8);
localparam C_MEM_MAP_ADDRA_WIDTH_MSB = C_ADDRA_WIDTH_MSB;
localparam C_MEM_MAP_ADDRB_WIDTH_MSB = C_ADDRB_WIDTH_MSB;
// Data Width Number of LSB address bits to be discarded
// 1 to 16 1
// 17 to 32 2
// 33 to 64 3
// 65 to 128 4
// 129 to 256 5
// 257 to 512 6
// 513 to 1024 7
// The following two constants determine this.
localparam MEM_MAP_LOWER_BOUND_VAL_A = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam MEM_MAP_LOWER_BOUND_VAL_B = (log2int(divroundup(C_WRITE_WIDTH_A,8)==0)) ? 0:(log2int(divroundup(C_WRITE_WIDTH_A,8)));
localparam C_MEM_MAP_ADDRA_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_A;
localparam C_MEM_MAP_ADDRB_WIDTH_LSB = MEM_MAP_LOWER_BOUND_VAL_B;
wire [C_ADDRB_WIDTH_ACTUAL-1 :0] rdaddrecc_i;
wire [C_ADDRB_WIDTH-1:C_MEM_MAP_ADDRB_WIDTH_MSB] msb_zero_i;
wire [C_MEM_MAP_ADDRB_WIDTH_LSB-1:0] lsb_zero_i;
assign msb_zero_i = 0;
assign lsb_zero_i = 0;
assign RDADDRECC = {msb_zero_i,rdaddrecc_i,lsb_zero_i};
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (C_HAS_ENA),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (C_USE_BYTE_WEA),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH_ACTUAL),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (C_HAS_ENB),
.C_HAS_REGCEB (C_HAS_REGCEB),
.C_USE_BYTE_WEB (C_USE_BYTE_WEB),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH_ACTUAL),
.C_HAS_MEM_OUTPUT_REGS_A (C_HAS_MEM_OUTPUT_REGS_A),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (C_HAS_MUX_OUTPUT_REGS_A),
.C_HAS_MUX_OUTPUT_REGS_B (C_HAS_MUX_OUTPUT_REGS_B),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (C_EN_ECC_PIPE),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (CLKA),
.RSTA (RSTA_I_SAFE),//(rsta_in),
.ENA (ENA_I_SAFE),//(ena_in),
.REGCEA (regcea_in),
.WEA (wea_in),
.ADDRA (addra_in[C_MEM_MAP_ADDRA_WIDTH_MSB-1:C_MEM_MAP_ADDRA_WIDTH_LSB]),
.DINA (dina_in),
.DOUTA (DOUTA),
.CLKB (CLKB),
.RSTB (RSTB_I_SAFE),//(RSTB),
.ENB (ENB_I_SAFE),//(ENB),
.REGCEB (REGCEB),
.WEB (WEB),
.ADDRB (ADDRB[C_MEM_MAP_ADDRB_WIDTH_MSB-1:C_MEM_MAP_ADDRB_WIDTH_LSB]),
.DINB (DINB),
.DOUTB (DOUTB),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.ECCPIPECE (ECCPIPECE),
.SLEEP (SLEEP),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.RDADDRECC (rdaddrecc_i)
);
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0 && C_HAS_MUX_OUTPUT_REGS_B == 0 ) begin : no_regs
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RLAST = s_axi_rlast_c;
assign S_AXI_RVALID = s_axi_rvalid_c;
assign S_AXI_RID = s_axi_rid_c;
assign S_AXI_RRESP = s_axi_rresp_c;
assign s_axi_rready_c = S_AXI_RREADY;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regceb
assign regceb_c = s_axi_rvalid_c && s_axi_rready_c;
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 0) begin : no_regceb
assign regceb_c = REGCEB;
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1) begin : only_core_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rdata_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RDATA = m_axi_payload_c[C_AXI_PAYLOAD-C_AXI_ID_WIDTH-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH-C_WRITE_WIDTH_B];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MEM_OUTPUT_REGS_B == 1) begin : only_emb_op_regs
assign s_axi_payload_c = {s_axi_rid_c,s_axi_rresp_c,s_axi_rlast_c};
assign S_AXI_RDATA = s_axi_rdata_c;
assign S_AXI_RID = m_axi_payload_c[C_AXI_PAYLOAD-1 : C_AXI_PAYLOAD-C_AXI_ID_WIDTH];
assign S_AXI_RRESP = m_axi_payload_c[2:1];
assign S_AXI_RLAST = m_axi_payload_c[0];
end
endgenerate
generate if (C_HAS_MUX_OUTPUT_REGS_B == 1 || C_HAS_MEM_OUTPUT_REGS_B == 1) begin : has_regs_fwd
blk_mem_axi_regs_fwd_v8_3
#(.C_DATA_WIDTH (C_AXI_PAYLOAD))
axi_regs_inst (
.ACLK (S_ACLK),
.ARESET (s_aresetn_a_c),
.S_VALID (s_axi_rvalid_c),
.S_READY (s_axi_rready_c),
.S_PAYLOAD_DATA (s_axi_payload_c),
.M_VALID (S_AXI_RVALID),
.M_READY (S_AXI_RREADY),
.M_PAYLOAD_DATA (m_axi_payload_c)
);
end
endgenerate
generate if (C_INTERFACE_TYPE == 1) begin : axi_mem_module
assign s_aresetn_a_c = !S_ARESETN;
assign S_AXI_BRESP = 2'b00;
assign s_axi_rresp_c = 2'b00;
assign s_axi_arlen_c = (C_AXI_TYPE == 1)?S_AXI_ARLEN:8'h0;
blk_mem_axi_write_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_AXI_AWADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_WDATA_WIDTH (C_WRITE_WIDTH_A),
.C_AXI_OS_WR (C_AXI_OS_WR))
axi_wr_fsm (
// AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
// AXI Full/Lite Slave Write interface
.S_AXI_AWADDR (S_AXI_AWADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_AWLEN (S_AXI_AWLEN),
.S_AXI_AWID (S_AXI_AWID),
.S_AXI_AWSIZE (S_AXI_AWSIZE),
.S_AXI_AWBURST (S_AXI_AWBURST),
.S_AXI_AWVALID (S_AXI_AWVALID),
.S_AXI_AWREADY (S_AXI_AWREADY),
.S_AXI_WVALID (S_AXI_WVALID),
.S_AXI_WREADY (S_AXI_WREADY),
.S_AXI_BVALID (S_AXI_BVALID),
.S_AXI_BREADY (S_AXI_BREADY),
.S_AXI_BID (S_AXI_BID),
// Signals for BRAM interfac(
.S_AXI_AWADDR_OUT (s_axi_awaddr_out_c),
.S_AXI_WR_EN (s_axi_wr_en_c)
);
blk_mem_axi_read_wrapper_beh_v8_3
#(.C_INTERFACE_TYPE (C_INTERFACE_TYPE),
.C_AXI_TYPE (C_AXI_TYPE),
.C_AXI_SLAVE_TYPE (C_AXI_SLAVE_TYPE),
.C_MEMORY_TYPE (C_MEM_TYPE),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_AXI_PIPELINE_STAGES (1),
.C_AXI_ARADDR_WIDTH ((AXI_FULL_MEMORY_SLAVE == 1)?C_AXI_ADDR_WIDTH:C_AXI_ADDR_WIDTH-C_AXI_ADDR_WIDTH_LSB),
.C_HAS_AXI_ID (C_HAS_AXI_ID),
.C_AXI_ID_WIDTH (C_AXI_ID_WIDTH),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH))
axi_rd_sm(
//AXI Global Signals
.S_ACLK (S_ACLK),
.S_ARESETN (s_aresetn_a_c),
//AXI Full/Lite Read Side
.S_AXI_ARADDR (S_AXI_ARADDR[C_AXI_ADDR_WIDTH_MSB-1:C_AXI_ADDR_WIDTH_LSB]),
.S_AXI_ARLEN (s_axi_arlen_c),
.S_AXI_ARSIZE (S_AXI_ARSIZE),
.S_AXI_ARBURST (S_AXI_ARBURST),
.S_AXI_ARVALID (S_AXI_ARVALID),
.S_AXI_ARREADY (S_AXI_ARREADY),
.S_AXI_RLAST (s_axi_rlast_c),
.S_AXI_RVALID (s_axi_rvalid_c),
.S_AXI_RREADY (s_axi_rready_c),
.S_AXI_ARID (S_AXI_ARID),
.S_AXI_RID (s_axi_rid_c),
//AXI Full/Lite Read FSM Outputs
.S_AXI_ARADDR_OUT (s_axi_araddr_out_c),
.S_AXI_RD_EN (s_axi_rd_en_c)
);
blk_mem_gen_v8_3_5_mem_module
#(.C_CORENAME (C_CORENAME),
.C_FAMILY (C_FAMILY),
.C_XDEVICEFAMILY (C_XDEVICEFAMILY),
.C_MEM_TYPE (C_MEM_TYPE),
.C_BYTE_SIZE (C_BYTE_SIZE),
.C_USE_BRAM_BLOCK (C_USE_BRAM_BLOCK),
.C_ALGORITHM (C_ALGORITHM),
.C_PRIM_TYPE (C_PRIM_TYPE),
.C_LOAD_INIT_FILE (C_LOAD_INIT_FILE),
.C_INIT_FILE_NAME (C_INIT_FILE_NAME),
.C_INIT_FILE (C_INIT_FILE),
.C_USE_DEFAULT_DATA (C_USE_DEFAULT_DATA),
.C_DEFAULT_DATA (C_DEFAULT_DATA),
.C_RST_TYPE ("SYNC"),
.C_HAS_RSTA (C_HAS_RSTA),
.C_RST_PRIORITY_A (C_RST_PRIORITY_A),
.C_RSTRAM_A (C_RSTRAM_A),
.C_INITA_VAL (C_INITA_VAL),
.C_HAS_ENA (1),
.C_HAS_REGCEA (C_HAS_REGCEA),
.C_USE_BYTE_WEA (1),
.C_WEA_WIDTH (C_WEA_WIDTH),
.C_WRITE_MODE_A (C_WRITE_MODE_A),
.C_WRITE_WIDTH_A (C_WRITE_WIDTH_A),
.C_READ_WIDTH_A (C_READ_WIDTH_A),
.C_WRITE_DEPTH_A (C_WRITE_DEPTH_A),
.C_READ_DEPTH_A (C_READ_DEPTH_A),
.C_ADDRA_WIDTH (C_ADDRA_WIDTH),
.C_HAS_RSTB (C_HAS_RSTB),
.C_RST_PRIORITY_B (C_RST_PRIORITY_B),
.C_RSTRAM_B (C_RSTRAM_B),
.C_INITB_VAL (C_INITB_VAL),
.C_HAS_ENB (1),
.C_HAS_REGCEB (C_HAS_MEM_OUTPUT_REGS_B),
.C_USE_BYTE_WEB (1),
.C_WEB_WIDTH (C_WEB_WIDTH),
.C_WRITE_MODE_B (C_WRITE_MODE_B),
.C_WRITE_WIDTH_B (C_WRITE_WIDTH_B),
.C_READ_WIDTH_B (C_READ_WIDTH_B),
.C_WRITE_DEPTH_B (C_WRITE_DEPTH_B),
.C_READ_DEPTH_B (C_READ_DEPTH_B),
.C_ADDRB_WIDTH (C_ADDRB_WIDTH),
.C_HAS_MEM_OUTPUT_REGS_A (0),
.C_HAS_MEM_OUTPUT_REGS_B (C_HAS_MEM_OUTPUT_REGS_B),
.C_HAS_MUX_OUTPUT_REGS_A (0),
.C_HAS_MUX_OUTPUT_REGS_B (0),
.C_HAS_SOFTECC_INPUT_REGS_A (C_HAS_SOFTECC_INPUT_REGS_A),
.C_HAS_SOFTECC_OUTPUT_REGS_B (C_HAS_SOFTECC_OUTPUT_REGS_B),
.C_MUX_PIPELINE_STAGES (C_MUX_PIPELINE_STAGES),
.C_USE_SOFTECC (C_USE_SOFTECC),
.C_USE_ECC (C_USE_ECC),
.C_HAS_INJECTERR (C_HAS_INJECTERR),
.C_SIM_COLLISION_CHECK (C_SIM_COLLISION_CHECK),
.C_COMMON_CLK (C_COMMON_CLK),
.FLOP_DELAY (FLOP_DELAY),
.C_DISABLE_WARN_BHV_COLL (C_DISABLE_WARN_BHV_COLL),
.C_EN_ECC_PIPE (0),
.C_DISABLE_WARN_BHV_RANGE (C_DISABLE_WARN_BHV_RANGE))
blk_mem_gen_v8_3_5_inst
(.CLKA (S_ACLK),
.RSTA (s_aresetn_a_c),
.ENA (s_axi_wr_en_c),
.REGCEA (regcea_in),
.WEA (S_AXI_WSTRB),
.ADDRA (s_axi_awaddr_out_c),
.DINA (S_AXI_WDATA),
.DOUTA (DOUTA),
.CLKB (S_ACLK),
.RSTB (s_aresetn_a_c),
.ENB (s_axi_rd_en_c),
.REGCEB (regceb_c),
.WEB (WEB_parameterized),
.ADDRB (s_axi_araddr_out_c),
.DINB (DINB),
.DOUTB (s_axi_rdata_c),
.INJECTSBITERR (injectsbiterr_in),
.INJECTDBITERR (injectdbiterr_in),
.SBITERR (SBITERR),
.DBITERR (DBITERR),
.ECCPIPECE (1'b0),
.SLEEP (1'b0),
.RDADDRECC (RDADDRECC)
);
end
endgenerate
endmodule
|
Require Import TestSuite.admit.
(** [not tac] is equivalent to [fail tac "succeeds"] if [tac] succeeds, and is equivalent to [idtac] if [tac] fails *)
Tactic Notation "not" tactic3(tac) :=
(tryif tac then fail 0 tac "succeeds" else idtac); (* error if the tactic solved all goals *) [].
(** Test if a tactic succeeds, but always roll-back the results *)
Tactic Notation "test" tactic3(tac) := tryif not tac then fail 0 tac "fails" else idtac.
Goal Set.
Proof.
not fail.
not not idtac.
not fail 0.
(** Would be nice if we could get [not fail 1] to pass, maybe *)
not not admit.
not not test admit.
not progress test admit.
(* test grouping *)
not (not idtac; fail).
assert True.
all:not fail.
2:not fail.
all:admit.
Defined.
Goal Set.
Proof.
test idtac.
test try fail.
test admit.
test match goal with |- Set => idtac end.
test (idtac; match goal with |- Set => idtac end).
(* test grouping *)
first [ (test idtac; fail); fail 1 | idtac ].
try test fail.
try test test fail.
test test idtac.
test test admit.
Fail test fail.
test (idtac; []).
test (assert True; [|]).
(* would be nice, perhaps, if we could catch [fail 1] and not just [fail 0] this *)
try ((test fail); fail 1).
assert True.
all:test idtac.
all:test admit.
2:test admit.
all:admit.
Defined.
|
Require Import TestSuite.admit.
(** [not tac] is equivalent to [fail tac "succeeds"] if [tac] succeeds, and is equivalent to [idtac] if [tac] fails *)
Tactic Notation "not" tactic3(tac) :=
(tryif tac then fail 0 tac "succeeds" else idtac); (* error if the tactic solved all goals *) [].
(** Test if a tactic succeeds, but always roll-back the results *)
Tactic Notation "test" tactic3(tac) := tryif not tac then fail 0 tac "fails" else idtac.
Goal Set.
Proof.
not fail.
not not idtac.
not fail 0.
(** Would be nice if we could get [not fail 1] to pass, maybe *)
not not admit.
not not test admit.
not progress test admit.
(* test grouping *)
not (not idtac; fail).
assert True.
all:not fail.
2:not fail.
all:admit.
Defined.
Goal Set.
Proof.
test idtac.
test try fail.
test admit.
test match goal with |- Set => idtac end.
test (idtac; match goal with |- Set => idtac end).
(* test grouping *)
first [ (test idtac; fail); fail 1 | idtac ].
try test fail.
try test test fail.
test test idtac.
test test admit.
Fail test fail.
test (idtac; []).
test (assert True; [|]).
(* would be nice, perhaps, if we could catch [fail 1] and not just [fail 0] this *)
try ((test fail); fail 1).
assert True.
all:test idtac.
all:test admit.
2:test admit.
all:admit.
Defined.
|
Require Import TestSuite.admit.
(** [not tac] is equivalent to [fail tac "succeeds"] if [tac] succeeds, and is equivalent to [idtac] if [tac] fails *)
Tactic Notation "not" tactic3(tac) :=
(tryif tac then fail 0 tac "succeeds" else idtac); (* error if the tactic solved all goals *) [].
(** Test if a tactic succeeds, but always roll-back the results *)
Tactic Notation "test" tactic3(tac) := tryif not tac then fail 0 tac "fails" else idtac.
Goal Set.
Proof.
not fail.
not not idtac.
not fail 0.
(** Would be nice if we could get [not fail 1] to pass, maybe *)
not not admit.
not not test admit.
not progress test admit.
(* test grouping *)
not (not idtac; fail).
assert True.
all:not fail.
2:not fail.
all:admit.
Defined.
Goal Set.
Proof.
test idtac.
test try fail.
test admit.
test match goal with |- Set => idtac end.
test (idtac; match goal with |- Set => idtac end).
(* test grouping *)
first [ (test idtac; fail); fail 1 | idtac ].
try test fail.
try test test fail.
test test idtac.
test test admit.
Fail test fail.
test (idtac; []).
test (assert True; [|]).
(* would be nice, perhaps, if we could catch [fail 1] and not just [fail 0] this *)
try ((test fail); fail 1).
assert True.
all:test idtac.
all:test admit.
2:test admit.
all:admit.
Defined.
|
///////////////////////////////////////////////////////////////////////////////
//
// File name: axi_protocol_converter_v2_1_b2s.v
//
// Description:
// To handle AXI4 transactions to external memory on Virtex-6 architectures
// requires a bridge to convert the AXI4 transactions to the memory
// controller(MC) user interface. The MC user interface has bidirectional
// data path and supports data width of 256/128/64/32 bits.
// The bridge is designed to allow AXI4 IP masters to communicate with
// the MC user interface.
//
//
// Specifications:
// AXI4 Slave Side:
// Configurable data width of 32, 64, 128, 256
// Read acceptance depth is:
// Write acceptance depth is:
//
// Structure:
// axi_protocol_converter_v2_1_b2s
// WRITE_BUNDLE
// aw_channel_0
// cmd_translator_0
// rd_cmd_fsm_0
// w_channel_0
// b_channel_0
// READ_BUNDLE
// ar_channel_0
// cmd_translator_0
// rd_cmd_fsm_0
// r_channel_0
//
///////////////////////////////////////////////////////////////////////////////
`timescale 1ps/1ps
`default_nettype none
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_protocol_converter_v2_1_b2s #(
parameter C_S_AXI_PROTOCOL = 0,
// Width of all master and slave ID signals.
// Range: >= 1.
parameter integer C_AXI_ID_WIDTH = 4,
parameter integer C_AXI_ADDR_WIDTH = 30,
parameter integer C_AXI_DATA_WIDTH = 32,
parameter integer C_AXI_SUPPORTS_WRITE = 1,
parameter integer C_AXI_SUPPORTS_READ = 1
)
(
///////////////////////////////////////////////////////////////////////////////
// Port Declarations
///////////////////////////////////////////////////////////////////////////////
// AXI Slave Interface
// Slave Interface System Signals
input wire aclk ,
input wire aresetn ,
// Slave Interface Write Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_awid ,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_awaddr ,
input wire [((C_S_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_awlen,
input wire [2:0] s_axi_awsize ,
input wire [1:0] s_axi_awburst ,
input wire [2:0] s_axi_awprot ,
input wire s_axi_awvalid ,
output wire s_axi_awready ,
// Slave Interface Write Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] s_axi_wdata ,
input wire [C_AXI_DATA_WIDTH/8-1:0] s_axi_wstrb ,
input wire s_axi_wlast ,
input wire s_axi_wvalid ,
output wire s_axi_wready ,
// Slave Interface Write Response Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_bid ,
output wire [1:0] s_axi_bresp ,
output wire s_axi_bvalid ,
input wire s_axi_bready ,
// Slave Interface Read Address Ports
input wire [C_AXI_ID_WIDTH-1:0] s_axi_arid ,
input wire [C_AXI_ADDR_WIDTH-1:0] s_axi_araddr ,
input wire [((C_S_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] s_axi_arlen,
input wire [2:0] s_axi_arsize ,
input wire [1:0] s_axi_arburst ,
input wire [2:0] s_axi_arprot ,
input wire s_axi_arvalid ,
output wire s_axi_arready ,
// Slave Interface Read Data Ports
output wire [C_AXI_ID_WIDTH-1:0] s_axi_rid ,
output wire [C_AXI_DATA_WIDTH-1:0] s_axi_rdata ,
output wire [1:0] s_axi_rresp ,
output wire s_axi_rlast ,
output wire s_axi_rvalid ,
input wire s_axi_rready ,
// Slave Interface Write Address Ports
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_awaddr ,
output wire [2:0] m_axi_awprot ,
output wire m_axi_awvalid ,
input wire m_axi_awready ,
// Slave Interface Write Data Ports
output wire [C_AXI_DATA_WIDTH-1:0] m_axi_wdata ,
output wire [C_AXI_DATA_WIDTH/8-1:0] m_axi_wstrb ,
output wire m_axi_wvalid ,
input wire m_axi_wready ,
// Slave Interface Write Response Ports
input wire [1:0] m_axi_bresp ,
input wire m_axi_bvalid ,
output wire m_axi_bready ,
// Slave Interface Read Address Ports
output wire [C_AXI_ADDR_WIDTH-1:0] m_axi_araddr ,
output wire [2:0] m_axi_arprot ,
output wire m_axi_arvalid ,
input wire m_axi_arready ,
// Slave Interface Read Data Ports
input wire [C_AXI_DATA_WIDTH-1:0] m_axi_rdata ,
input wire [1:0] m_axi_rresp ,
input wire m_axi_rvalid ,
output wire m_axi_rready
);
////////////////////////////////////////////////////////////////////////////////
// Wires/Reg declarations
////////////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
// BEGIN RTL
reg areset_d1;
always @(posedge aclk)
areset_d1 <= ~aresetn;
// AW/W/B channel internal communication
wire b_push;
wire [C_AXI_ID_WIDTH-1:0] b_awid;
wire [7:0] b_awlen;
wire b_full;
wire [C_AXI_ID_WIDTH-1:0] si_rs_awid;
wire [C_AXI_ADDR_WIDTH-1:0] si_rs_awaddr;
wire [8-1:0] si_rs_awlen;
wire [3-1:0] si_rs_awsize;
wire [2-1:0] si_rs_awburst;
wire [3-1:0] si_rs_awprot;
wire si_rs_awvalid;
wire si_rs_awready;
wire [C_AXI_DATA_WIDTH-1:0] si_rs_wdata;
wire [C_AXI_DATA_WIDTH/8-1:0] si_rs_wstrb;
wire si_rs_wlast;
wire si_rs_wvalid;
wire si_rs_wready;
wire [C_AXI_ID_WIDTH-1:0] si_rs_bid;
wire [2-1:0] si_rs_bresp;
wire si_rs_bvalid;
wire si_rs_bready;
wire [C_AXI_ID_WIDTH-1:0] si_rs_arid;
wire [C_AXI_ADDR_WIDTH-1:0] si_rs_araddr;
wire [8-1:0] si_rs_arlen;
wire [3-1:0] si_rs_arsize;
wire [2-1:0] si_rs_arburst;
wire [3-1:0] si_rs_arprot;
wire si_rs_arvalid;
wire si_rs_arready;
wire [C_AXI_ID_WIDTH-1:0] si_rs_rid;
wire [C_AXI_DATA_WIDTH-1:0] si_rs_rdata;
wire [2-1:0] si_rs_rresp;
wire si_rs_rlast;
wire si_rs_rvalid;
wire si_rs_rready;
wire [C_AXI_ADDR_WIDTH-1:0] rs_mi_awaddr;
wire rs_mi_awvalid;
wire rs_mi_awready;
wire [C_AXI_DATA_WIDTH-1:0] rs_mi_wdata;
wire [C_AXI_DATA_WIDTH/8-1:0] rs_mi_wstrb;
wire rs_mi_wvalid;
wire rs_mi_wready;
wire [2-1:0] rs_mi_bresp;
wire rs_mi_bvalid;
wire rs_mi_bready;
wire [C_AXI_ADDR_WIDTH-1:0] rs_mi_araddr;
wire rs_mi_arvalid;
wire rs_mi_arready;
wire [C_AXI_DATA_WIDTH-1:0] rs_mi_rdata;
wire [2-1:0] rs_mi_rresp;
wire rs_mi_rvalid;
wire rs_mi_rready;
axi_register_slice_v2_1_axi_register_slice #(
.C_AXI_PROTOCOL ( C_S_AXI_PROTOCOL ) ,
.C_AXI_ID_WIDTH ( C_AXI_ID_WIDTH ) ,
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH ) ,
.C_AXI_DATA_WIDTH ( C_AXI_DATA_WIDTH ) ,
.C_AXI_SUPPORTS_USER_SIGNALS ( 0 ) ,
.C_AXI_AWUSER_WIDTH ( 1 ) ,
.C_AXI_ARUSER_WIDTH ( 1 ) ,
.C_AXI_WUSER_WIDTH ( 1 ) ,
.C_AXI_RUSER_WIDTH ( 1 ) ,
.C_AXI_BUSER_WIDTH ( 1 ) ,
.C_REG_CONFIG_AW ( 1 ) ,
.C_REG_CONFIG_AR ( 1 ) ,
.C_REG_CONFIG_W ( 0 ) ,
.C_REG_CONFIG_R ( 1 ) ,
.C_REG_CONFIG_B ( 1 )
) SI_REG (
.aresetn ( aresetn ) ,
.aclk ( aclk ) ,
.s_axi_awid ( s_axi_awid ) ,
.s_axi_awaddr ( s_axi_awaddr ) ,
.s_axi_awlen ( s_axi_awlen ) ,
.s_axi_awsize ( s_axi_awsize ) ,
.s_axi_awburst ( s_axi_awburst ) ,
.s_axi_awlock ( {((C_S_AXI_PROTOCOL == 1) ? 2 : 1){1'b0}} ) ,
.s_axi_awcache ( 4'h0 ) ,
.s_axi_awprot ( s_axi_awprot ) ,
.s_axi_awqos ( 4'h0 ) ,
.s_axi_awuser ( 1'b0 ) ,
.s_axi_awvalid ( s_axi_awvalid ) ,
.s_axi_awready ( s_axi_awready ) ,
.s_axi_awregion ( 4'h0 ) ,
.s_axi_wid ( {C_AXI_ID_WIDTH{1'b0}} ) ,
.s_axi_wdata ( s_axi_wdata ) ,
.s_axi_wstrb ( s_axi_wstrb ) ,
.s_axi_wlast ( s_axi_wlast ) ,
.s_axi_wuser ( 1'b0 ) ,
.s_axi_wvalid ( s_axi_wvalid ) ,
.s_axi_wready ( s_axi_wready ) ,
.s_axi_bid ( s_axi_bid ) ,
.s_axi_bresp ( s_axi_bresp ) ,
.s_axi_buser ( ) ,
.s_axi_bvalid ( s_axi_bvalid ) ,
.s_axi_bready ( s_axi_bready ) ,
.s_axi_arid ( s_axi_arid ) ,
.s_axi_araddr ( s_axi_araddr ) ,
.s_axi_arlen ( s_axi_arlen ) ,
.s_axi_arsize ( s_axi_arsize ) ,
.s_axi_arburst ( s_axi_arburst ) ,
.s_axi_arlock ( {((C_S_AXI_PROTOCOL == 1) ? 2 : 1){1'b0}} ) ,
.s_axi_arcache ( 4'h0 ) ,
.s_axi_arprot ( s_axi_arprot ) ,
.s_axi_arqos ( 4'h0 ) ,
.s_axi_aruser ( 1'b0 ) ,
.s_axi_arvalid ( s_axi_arvalid ) ,
.s_axi_arready ( s_axi_arready ) ,
.s_axi_arregion ( 4'h0 ) ,
.s_axi_rid ( s_axi_rid ) ,
.s_axi_rdata ( s_axi_rdata ) ,
.s_axi_rresp ( s_axi_rresp ) ,
.s_axi_rlast ( s_axi_rlast ) ,
.s_axi_ruser ( ) ,
.s_axi_rvalid ( s_axi_rvalid ) ,
.s_axi_rready ( s_axi_rready ) ,
.m_axi_awid ( si_rs_awid ) ,
.m_axi_awaddr ( si_rs_awaddr ) ,
.m_axi_awlen ( si_rs_awlen[((C_S_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] ) ,
.m_axi_awsize ( si_rs_awsize ) ,
.m_axi_awburst ( si_rs_awburst ) ,
.m_axi_awlock ( ) ,
.m_axi_awcache ( ) ,
.m_axi_awprot ( si_rs_awprot ) ,
.m_axi_awqos ( ) ,
.m_axi_awuser ( ) ,
.m_axi_awvalid ( si_rs_awvalid ) ,
.m_axi_awready ( si_rs_awready ) ,
.m_axi_awregion ( ) ,
.m_axi_wid ( ) ,
.m_axi_wdata ( si_rs_wdata ) ,
.m_axi_wstrb ( si_rs_wstrb ) ,
.m_axi_wlast ( si_rs_wlast ) ,
.m_axi_wuser ( ) ,
.m_axi_wvalid ( si_rs_wvalid ) ,
.m_axi_wready ( si_rs_wready ) ,
.m_axi_bid ( si_rs_bid ) ,
.m_axi_bresp ( si_rs_bresp ) ,
.m_axi_buser ( 1'b0 ) ,
.m_axi_bvalid ( si_rs_bvalid ) ,
.m_axi_bready ( si_rs_bready ) ,
.m_axi_arid ( si_rs_arid ) ,
.m_axi_araddr ( si_rs_araddr ) ,
.m_axi_arlen ( si_rs_arlen[((C_S_AXI_PROTOCOL == 1) ? 4 : 8)-1:0] ) ,
.m_axi_arsize ( si_rs_arsize ) ,
.m_axi_arburst ( si_rs_arburst ) ,
.m_axi_arlock ( ) ,
.m_axi_arcache ( ) ,
.m_axi_arprot ( si_rs_arprot ) ,
.m_axi_arqos ( ) ,
.m_axi_aruser ( ) ,
.m_axi_arvalid ( si_rs_arvalid ) ,
.m_axi_arready ( si_rs_arready ) ,
.m_axi_arregion ( ) ,
.m_axi_rid ( si_rs_rid ) ,
.m_axi_rdata ( si_rs_rdata ) ,
.m_axi_rresp ( si_rs_rresp ) ,
.m_axi_rlast ( si_rs_rlast ) ,
.m_axi_ruser ( 1'b0 ) ,
.m_axi_rvalid ( si_rs_rvalid ) ,
.m_axi_rready ( si_rs_rready )
);
generate
if (C_AXI_SUPPORTS_WRITE == 1) begin : WR
axi_protocol_converter_v2_1_b2s_aw_channel #
(
.C_ID_WIDTH ( C_AXI_ID_WIDTH ),
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH )
)
aw_channel_0
(
.clk ( aclk ) ,
.reset ( areset_d1 ) ,
.s_awid ( si_rs_awid ) ,
.s_awaddr ( si_rs_awaddr ) ,
.s_awlen ( (C_S_AXI_PROTOCOL == 1) ? {4'h0,si_rs_awlen[3:0]} : si_rs_awlen),
.s_awsize ( si_rs_awsize ) ,
.s_awburst ( si_rs_awburst ) ,
.s_awvalid ( si_rs_awvalid ) ,
.s_awready ( si_rs_awready ) ,
.m_awvalid ( rs_mi_awvalid ) ,
.m_awaddr ( rs_mi_awaddr ) ,
.m_awready ( rs_mi_awready ) ,
.b_push ( b_push ) ,
.b_awid ( b_awid ) ,
.b_awlen ( b_awlen ) ,
.b_full ( b_full )
);
axi_protocol_converter_v2_1_b2s_b_channel #
(
.C_ID_WIDTH ( C_AXI_ID_WIDTH )
)
b_channel_0
(
.clk ( aclk ) ,
.reset ( areset_d1 ) ,
.s_bid ( si_rs_bid ) ,
.s_bresp ( si_rs_bresp ) ,
.s_bvalid ( si_rs_bvalid ) ,
.s_bready ( si_rs_bready ) ,
.m_bready ( rs_mi_bready ) ,
.m_bvalid ( rs_mi_bvalid ) ,
.m_bresp ( rs_mi_bresp ) ,
.b_push ( b_push ) ,
.b_awid ( b_awid ) ,
.b_awlen ( b_awlen ) ,
.b_full ( b_full ) ,
.b_resp_rdy ( si_rs_awready )
);
assign rs_mi_wdata = si_rs_wdata;
assign rs_mi_wstrb = si_rs_wstrb;
assign rs_mi_wvalid = si_rs_wvalid;
assign si_rs_wready = rs_mi_wready;
end else begin : NO_WR
assign rs_mi_awaddr = {C_AXI_ADDR_WIDTH{1'b0}};
assign rs_mi_awvalid = 1'b0;
assign si_rs_awready = 1'b0;
assign rs_mi_wdata = {C_AXI_DATA_WIDTH{1'b0}};
assign rs_mi_wstrb = {C_AXI_DATA_WIDTH/8{1'b0}};
assign rs_mi_wvalid = 1'b0;
assign si_rs_wready = 1'b0;
assign rs_mi_bready = 1'b0;
assign si_rs_bvalid = 1'b0;
assign si_rs_bresp = 2'b00;
assign si_rs_bid = {C_AXI_ID_WIDTH{1'b0}};
end
endgenerate
// AR/R channel communication
wire r_push ;
wire [C_AXI_ID_WIDTH-1:0] r_arid ;
wire r_rlast ;
wire r_full ;
generate
if (C_AXI_SUPPORTS_READ == 1) begin : RD
axi_protocol_converter_v2_1_b2s_ar_channel #
(
.C_ID_WIDTH ( C_AXI_ID_WIDTH ),
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH )
)
ar_channel_0
(
.clk ( aclk ) ,
.reset ( areset_d1 ) ,
.s_arid ( si_rs_arid ) ,
.s_araddr ( si_rs_araddr ) ,
.s_arlen ( (C_S_AXI_PROTOCOL == 1) ? {4'h0,si_rs_arlen[3:0]} : si_rs_arlen),
.s_arsize ( si_rs_arsize ) ,
.s_arburst ( si_rs_arburst ) ,
.s_arvalid ( si_rs_arvalid ) ,
.s_arready ( si_rs_arready ) ,
.m_arvalid ( rs_mi_arvalid ) ,
.m_araddr ( rs_mi_araddr ) ,
.m_arready ( rs_mi_arready ) ,
.r_push ( r_push ) ,
.r_arid ( r_arid ) ,
.r_rlast ( r_rlast ) ,
.r_full ( r_full )
);
axi_protocol_converter_v2_1_b2s_r_channel #
(
.C_ID_WIDTH ( C_AXI_ID_WIDTH ),
.C_DATA_WIDTH ( C_AXI_DATA_WIDTH )
)
r_channel_0
(
.clk ( aclk ) ,
.reset ( areset_d1 ) ,
.s_rid ( si_rs_rid ) ,
.s_rdata ( si_rs_rdata ) ,
.s_rresp ( si_rs_rresp ) ,
.s_rlast ( si_rs_rlast ) ,
.s_rvalid ( si_rs_rvalid ) ,
.s_rready ( si_rs_rready ) ,
.m_rvalid ( rs_mi_rvalid ) ,
.m_rready ( rs_mi_rready ) ,
.m_rdata ( rs_mi_rdata ) ,
.m_rresp ( rs_mi_rresp ) ,
.r_push ( r_push ) ,
.r_full ( r_full ) ,
.r_arid ( r_arid ) ,
.r_rlast ( r_rlast )
);
end else begin : NO_RD
assign rs_mi_araddr = {C_AXI_ADDR_WIDTH{1'b0}};
assign rs_mi_arvalid = 1'b0;
assign si_rs_arready = 1'b0;
assign si_rs_rlast = 1'b1;
assign si_rs_rdata = {C_AXI_DATA_WIDTH{1'b0}};
assign si_rs_rvalid = 1'b0;
assign si_rs_rresp = 2'b00;
assign si_rs_rid = {C_AXI_ID_WIDTH{1'b0}};
assign rs_mi_rready = 1'b0;
end
endgenerate
axi_register_slice_v2_1_axi_register_slice #(
.C_AXI_PROTOCOL ( 2 ) ,
.C_AXI_ID_WIDTH ( 1 ) ,
.C_AXI_ADDR_WIDTH ( C_AXI_ADDR_WIDTH ) ,
.C_AXI_DATA_WIDTH ( C_AXI_DATA_WIDTH ) ,
.C_AXI_SUPPORTS_USER_SIGNALS ( 0 ) ,
.C_AXI_AWUSER_WIDTH ( 1 ) ,
.C_AXI_ARUSER_WIDTH ( 1 ) ,
.C_AXI_WUSER_WIDTH ( 1 ) ,
.C_AXI_RUSER_WIDTH ( 1 ) ,
.C_AXI_BUSER_WIDTH ( 1 ) ,
.C_REG_CONFIG_AW ( 0 ) ,
.C_REG_CONFIG_AR ( 0 ) ,
.C_REG_CONFIG_W ( 0 ) ,
.C_REG_CONFIG_R ( 0 ) ,
.C_REG_CONFIG_B ( 0 )
) MI_REG (
.aresetn ( aresetn ) ,
.aclk ( aclk ) ,
.s_axi_awid ( 1'b0 ) ,
.s_axi_awaddr ( rs_mi_awaddr ) ,
.s_axi_awlen ( 8'h00 ) ,
.s_axi_awsize ( 3'b000 ) ,
.s_axi_awburst ( 2'b01 ) ,
.s_axi_awlock ( 1'b0 ) ,
.s_axi_awcache ( 4'h0 ) ,
.s_axi_awprot ( si_rs_awprot ) ,
.s_axi_awqos ( 4'h0 ) ,
.s_axi_awuser ( 1'b0 ) ,
.s_axi_awvalid ( rs_mi_awvalid ) ,
.s_axi_awready ( rs_mi_awready ) ,
.s_axi_awregion ( 4'h0 ) ,
.s_axi_wid ( 1'b0 ) ,
.s_axi_wdata ( rs_mi_wdata ) ,
.s_axi_wstrb ( rs_mi_wstrb ) ,
.s_axi_wlast ( 1'b1 ) ,
.s_axi_wuser ( 1'b0 ) ,
.s_axi_wvalid ( rs_mi_wvalid ) ,
.s_axi_wready ( rs_mi_wready ) ,
.s_axi_bid ( ) ,
.s_axi_bresp ( rs_mi_bresp ) ,
.s_axi_buser ( ) ,
.s_axi_bvalid ( rs_mi_bvalid ) ,
.s_axi_bready ( rs_mi_bready ) ,
.s_axi_arid ( 1'b0 ) ,
.s_axi_araddr ( rs_mi_araddr ) ,
.s_axi_arlen ( 8'h00 ) ,
.s_axi_arsize ( 3'b000 ) ,
.s_axi_arburst ( 2'b01 ) ,
.s_axi_arlock ( 1'b0 ) ,
.s_axi_arcache ( 4'h0 ) ,
.s_axi_arprot ( si_rs_arprot ) ,
.s_axi_arqos ( 4'h0 ) ,
.s_axi_aruser ( 1'b0 ) ,
.s_axi_arvalid ( rs_mi_arvalid ) ,
.s_axi_arready ( rs_mi_arready ) ,
.s_axi_arregion ( 4'h0 ) ,
.s_axi_rid ( ) ,
.s_axi_rdata ( rs_mi_rdata ) ,
.s_axi_rresp ( rs_mi_rresp ) ,
.s_axi_rlast ( ) ,
.s_axi_ruser ( ) ,
.s_axi_rvalid ( rs_mi_rvalid ) ,
.s_axi_rready ( rs_mi_rready ) ,
.m_axi_awid ( ) ,
.m_axi_awaddr ( m_axi_awaddr ) ,
.m_axi_awlen ( ) ,
.m_axi_awsize ( ) ,
.m_axi_awburst ( ) ,
.m_axi_awlock ( ) ,
.m_axi_awcache ( ) ,
.m_axi_awprot ( m_axi_awprot ) ,
.m_axi_awqos ( ) ,
.m_axi_awuser ( ) ,
.m_axi_awvalid ( m_axi_awvalid ) ,
.m_axi_awready ( m_axi_awready ) ,
.m_axi_awregion ( ) ,
.m_axi_wid ( ) ,
.m_axi_wdata ( m_axi_wdata ) ,
.m_axi_wstrb ( m_axi_wstrb ) ,
.m_axi_wlast ( ) ,
.m_axi_wuser ( ) ,
.m_axi_wvalid ( m_axi_wvalid ) ,
.m_axi_wready ( m_axi_wready ) ,
.m_axi_bid ( 1'b0 ) ,
.m_axi_bresp ( m_axi_bresp ) ,
.m_axi_buser ( 1'b0 ) ,
.m_axi_bvalid ( m_axi_bvalid ) ,
.m_axi_bready ( m_axi_bready ) ,
.m_axi_arid ( ) ,
.m_axi_araddr ( m_axi_araddr ) ,
.m_axi_arlen ( ) ,
.m_axi_arsize ( ) ,
.m_axi_arburst ( ) ,
.m_axi_arlock ( ) ,
.m_axi_arcache ( ) ,
.m_axi_arprot ( m_axi_arprot ) ,
.m_axi_arqos ( ) ,
.m_axi_aruser ( ) ,
.m_axi_arvalid ( m_axi_arvalid ) ,
.m_axi_arready ( m_axi_arready ) ,
.m_axi_arregion ( ) ,
.m_axi_rid ( 1'b0 ) ,
.m_axi_rdata ( m_axi_rdata ) ,
.m_axi_rresp ( m_axi_rresp ) ,
.m_axi_rlast ( 1'b1 ) ,
.m_axi_ruser ( 1'b0 ) ,
.m_axi_rvalid ( m_axi_rvalid ) ,
.m_axi_rready ( m_axi_rready )
);
endmodule
`default_nettype wire
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/15/2016 01:13:48 PM
// Design Name:
// Module Name: Add_Subt
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Add_Subt
#(parameter SWR=26) (
input wire clk,
input wire rst,
input wire load_i,//Reg load input
input wire Add_Sub_op_i,
input wire [SWR-1:0] Data_A_i,
input wire [SWR-1:0] PreData_B_i,
/////////////////////////////////////////////////////////////
output wire [SWR-1:0] Data_Result_o,
//output wire [SWR-1:0] P_o,
//output wire [SWR-1:1] Cn_o,
output wire FSM_C_o
);
wire [SWR-1:0] Data_B;
wire [SWR:0] S_to_D;
wire [SWR-1:0] P_to_D;
wire [SWR-1:1] C_to_D;
wire Co_to_D;
//wire Co_to_gate;
/*
/////////////////////////////////////////7
genvar j;
for (j=0; j<SWR; j=j+1)begin
assign Data_B[j] = PreData_B_i[j] ^ Add_Sub_op_i;
end
Full_Adder_PG #(.SWR(SWR)) AS_Module(
.clk(clk),
.rst(rst),
.Op_A_i(Data_A_i),
.Op_B_i(Data_B),
.C_i(Add_Sub_op_i), //Carry in
.S_o(S_to_D), // Solution out
.Cn_o(C_to_D),
.C_o(Co_to_gate), //Carry out
.P_o(P_o) //Propagate (for LZA)
);*/
add_sub_carry_out #(.W(SWR)) Sgf_AS (
.op_mode(Add_Sub_op_i),
.Data_A(Data_A_i),
.Data_B(PreData_B_i),
.Data_S(S_to_D)
);
assign Co_to_D = S_to_D[SWR] & ~Add_Sub_op_i;
RegisterAdd #(.W(SWR)) Add_Subt_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (S_to_D[SWR-1:0]),
.Q (Data_Result_o)
);
/*RegisterAdd #(.W(SWR)) P_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (P_to_D),
.Q (P_o)
);*/
/*RegisterAdd #(.W(SWR-1)) C_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (C_to_D),
.Q (Cn_o)
);*/
RegisterAdd #(.W(1)) Add_overflow_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (S_to_D[SWR]),
.Q (FSM_C_o)
);
endmodule
|
`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////
// Company:
// Engineer:
//
// Create Date: 03/15/2016 01:13:48 PM
// Design Name:
// Module Name: Add_Subt
// Project Name:
// Target Devices:
// Tool Versions:
// Description:
//
// Dependencies:
//
// Revision:
// Revision 0.01 - File Created
// Additional Comments:
//
//////////////////////////////////////////////////////////////////////////////////
module Add_Subt
#(parameter SWR=26) (
input wire clk,
input wire rst,
input wire load_i,//Reg load input
input wire Add_Sub_op_i,
input wire [SWR-1:0] Data_A_i,
input wire [SWR-1:0] PreData_B_i,
/////////////////////////////////////////////////////////////
output wire [SWR-1:0] Data_Result_o,
//output wire [SWR-1:0] P_o,
//output wire [SWR-1:1] Cn_o,
output wire FSM_C_o
);
wire [SWR-1:0] Data_B;
wire [SWR:0] S_to_D;
wire [SWR-1:0] P_to_D;
wire [SWR-1:1] C_to_D;
wire Co_to_D;
//wire Co_to_gate;
/*
/////////////////////////////////////////7
genvar j;
for (j=0; j<SWR; j=j+1)begin
assign Data_B[j] = PreData_B_i[j] ^ Add_Sub_op_i;
end
Full_Adder_PG #(.SWR(SWR)) AS_Module(
.clk(clk),
.rst(rst),
.Op_A_i(Data_A_i),
.Op_B_i(Data_B),
.C_i(Add_Sub_op_i), //Carry in
.S_o(S_to_D), // Solution out
.Cn_o(C_to_D),
.C_o(Co_to_gate), //Carry out
.P_o(P_o) //Propagate (for LZA)
);*/
add_sub_carry_out #(.W(SWR)) Sgf_AS (
.op_mode(Add_Sub_op_i),
.Data_A(Data_A_i),
.Data_B(PreData_B_i),
.Data_S(S_to_D)
);
assign Co_to_D = S_to_D[SWR] & ~Add_Sub_op_i;
RegisterAdd #(.W(SWR)) Add_Subt_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (S_to_D[SWR-1:0]),
.Q (Data_Result_o)
);
/*RegisterAdd #(.W(SWR)) P_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (P_to_D),
.Q (P_o)
);*/
/*RegisterAdd #(.W(SWR-1)) C_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (C_to_D),
.Q (Cn_o)
);*/
RegisterAdd #(.W(1)) Add_overflow_Result(
.clk (clk),
.rst (rst),
.load (load_i),
.D (S_to_D[SWR]),
.Q (FSM_C_o)
);
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2009 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
// Filename: trace_buffer.v
// Description: Trace port buffer
//-----------------------------------------------------------------------------
// Structure: This section shows the hierarchical structure of
// pss_wrapper.
//
// --processing_system7
// |
// --trace_buffer
//-----------------------------------------------------------------------------
module processing_system7_v5_5_trace_buffer #
(
parameter integer FIFO_SIZE = 128,
parameter integer USE_TRACE_DATA_EDGE_DETECTOR = 0,
parameter integer C_DELAY_CLKS = 12
)
(
input wire TRACE_CLK,
input wire RST,
input wire TRACE_VALID_IN,
input wire [3:0] TRACE_ATID_IN,
input wire [31:0] TRACE_DATA_IN,
output wire TRACE_VALID_OUT,
output wire [3:0] TRACE_ATID_OUT,
output wire [31:0] TRACE_DATA_OUT
);
//------------------------------------------------------------
// Architecture section
//------------------------------------------------------------
// function called clogb2 that returns an integer which has the
// value of the ceiling of the log base 2.
function integer clogb2 (input integer bit_depth);
integer i;
integer temp_log;
begin
temp_log = 0;
for(i=bit_depth; i > 0; i = i>>1)
clogb2 = temp_log;
temp_log=temp_log+1;
end
endfunction
localparam DEPTH = clogb2(FIFO_SIZE-1);
wire [31:0] reset_zeros;
reg [31:0] trace_pedge; // write enable for FIFO
reg [31:0] ti;
reg [31:0] tom;
reg [3:0] atid;
reg [31:0] trace_fifo [FIFO_SIZE-1:0];//Memory
reg [4:0] dly_ctr;
reg [DEPTH-1:0] fifo_wp;
reg [DEPTH-1:0] fifo_rp;
reg fifo_re;
wire fifo_empty;
wire fifo_full;
reg fifo_full_reg;
assign reset_zeros = 32'h0;
// Pipeline Stage for Traceport ATID ports
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
atid <= reset_zeros;
end
else begin
atid <= TRACE_ATID_IN;
end
end
assign TRACE_ATID_OUT = atid;
/////////////////////////////////////////////
// Generate FIFO data based on TRACE_VALID_IN
/////////////////////////////////////////////
generate
if (USE_TRACE_DATA_EDGE_DETECTOR == 0) begin : gen_no_data_edge_detector
/////////////////////////////////////////////
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if (TRACE_VALID_IN == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= TRACE_DATA_IN;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(TRACE_VALID_IN ) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
/////////////////////////////////////////////
// Generate FIFO data based on data edge
/////////////////////////////////////////////
end else begin : gen_data_edge_detector
/////////////////////////////////////////////
// purpose: check for pos edge on any trace input
always @(posedge TRACE_CLK) begin
// process pedge_ti
// rising clock edge
if((RST == 1'b1)) begin
ti <= reset_zeros;
trace_pedge <= reset_zeros;
end
else begin
ti <= TRACE_DATA_IN;
trace_pedge <= (~ti & TRACE_DATA_IN);
//trace_pedge <= ((~ti ^ TRACE_DATA_IN)) & ~ti;
// posedge only
end
end
// memory update process
// Update memory when positive edge detected and FIFO not full
always @(posedge TRACE_CLK) begin
if(|(trace_pedge) == 1'b1 && fifo_full_reg != 1'b1) begin
trace_fifo[fifo_wp] <= trace_pedge;
end
end
// fifo write pointer
always @(posedge TRACE_CLK) begin
// process
if(RST == 1'b1) begin
fifo_wp <= {DEPTH{1'b0}};
end
else if(|(trace_pedge) == 1'b1) begin
if(fifo_wp == (FIFO_SIZE - 1)) begin
if (fifo_empty) begin
fifo_wp <= {DEPTH{1'b0}};
end
end
else begin
fifo_wp <= fifo_wp + 1;
end
end
end
end
endgenerate
always @(posedge TRACE_CLK) begin
tom <= trace_fifo[fifo_rp] ;
end
// // fifo write pointer
// always @(posedge TRACE_CLK) begin
// // process
// if(RST == 1'b1) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else if(|(trace_pedge) == 1'b1) begin
// if(fifo_wp == (FIFO_SIZE - 1)) begin
// fifo_wp <= {DEPTH{1'b0}};
// end
// else begin
// fifo_wp <= fifo_wp + 1;
// end
// end
// end
// fifo read pointer update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_rp <= {DEPTH{1'b0}};
fifo_re <= 1'b0;
end
else if(fifo_empty != 1'b1 && dly_ctr == 5'b00000 && fifo_re == 1'b0) begin
fifo_re <= 1'b1;
if(fifo_rp == (FIFO_SIZE - 1)) begin
fifo_rp <= {DEPTH{1'b0}};
end
else begin
fifo_rp <= fifo_rp + 1;
end
end
else begin
fifo_re <= 1'b0;
end
end
// delay counter update
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
dly_ctr <= 5'h0;
end
else if (fifo_re == 1'b1) begin
dly_ctr <= C_DELAY_CLKS-1;
end
else if(dly_ctr != 5'h0) begin
dly_ctr <= dly_ctr - 1;
end
end
// fifo empty update
assign fifo_empty = (fifo_wp == fifo_rp) ? 1'b1 : 1'b0;
// fifo full update
assign fifo_full = (fifo_wp == FIFO_SIZE-1)? 1'b1 : 1'b0;
always @(posedge TRACE_CLK) begin
if(RST == 1'b1) begin
fifo_full_reg <= 1'b0;
end
else if (fifo_empty) begin
fifo_full_reg <= 1'b0;
end else begin
fifo_full_reg <= fifo_full;
end
end
// always @(posedge TRACE_CLK) begin
// if(RST == 1'b1) begin
// fifo_full_reg <= 1'b0;
// end
// else if ((fifo_wp == FIFO_SIZE-1) && (|(trace_pedge) == 1'b1)) begin
// fifo_full_reg <= 1'b1;
// end
// else begin
// fifo_full_reg <= 1'b0;
// end
// end
//
assign TRACE_DATA_OUT = tom;
assign TRACE_VALID_OUT = fifo_re;
endmodule
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Register Slice
// Generic single-channel AXI pipeline register on forward and/or reverse signal path
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// axic_register_slice
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_register_slice_v2_1_axic_register_slice #
(
parameter C_FAMILY = "virtex6",
parameter C_DATA_WIDTH = 32,
parameter C_REG_CONFIG = 32'h00000000
// C_REG_CONFIG:
// 0 => BYPASS = The channel is just wired through the module.
// 1 => FWD_REV = Both FWD and REV (fully-registered)
// 2 => FWD = The master VALID and payload signals are registrated.
// 3 => REV = The slave ready signal is registrated
// 4 => RESERVED (all outputs driven to 0).
// 5 => RESERVED (all outputs driven to 0).
// 6 => INPUTS = Slave and Master side inputs are registrated.
// 7 => LIGHT_WT = 1-stage pipeline register with bubble cycle, both FWD and REV pipelining
)
(
// System Signals
input wire ACLK,
input wire ARESET,
// Slave side
input wire [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
input wire S_VALID,
output wire S_READY,
// Master side
output wire [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA,
output wire M_VALID,
input wire M_READY
);
(* use_clock_enable = "yes" *)
generate
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 0
// Bypass mode
//
////////////////////////////////////////////////////////////////////
if (C_REG_CONFIG == 32'h00000000) begin
assign M_PAYLOAD_DATA = S_PAYLOAD_DATA;
assign M_VALID = S_VALID;
assign S_READY = M_READY;
end
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 1 (or 8)
// Both FWD and REV mode
//
////////////////////////////////////////////////////////////////////
else if ((C_REG_CONFIG == 32'h00000001) || (C_REG_CONFIG == 32'h00000008)) begin
reg [C_DATA_WIDTH-1:0] m_payload_i;
reg [C_DATA_WIDTH-1:0] skid_buffer;
reg s_ready_i;
reg m_valid_i;
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign M_PAYLOAD_DATA = m_payload_i;
reg [1:0] aresetn_d = 2'b00; // Reset delay shifter
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
always @(posedge ACLK) begin
if (~aresetn_d[0]) begin
s_ready_i <= 1'b0;
end else begin
s_ready_i <= M_READY | ~m_valid_i | (s_ready_i & ~S_VALID);
end
if (~aresetn_d[1]) begin
m_valid_i <= 1'b0;
end else begin
m_valid_i <= S_VALID | ~s_ready_i | (m_valid_i & ~M_READY);
end
if (M_READY | ~m_valid_i) begin
m_payload_i <= s_ready_i ? S_PAYLOAD_DATA : skid_buffer;
end
if (s_ready_i) begin
skid_buffer <= S_PAYLOAD_DATA;
end
end
end // if (C_REG_CONFIG == 1)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 2
// Only FWD mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000002)
begin
reg [C_DATA_WIDTH-1:0] storage_data;
wire s_ready_i; //local signal of output
reg m_valid_i; //local signal of output
// assign local signal to its output signal
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
reg aresetn_d = 1'b0; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 1'b0;
end else begin
aresetn_d <= ~ARESET;
end
end
// Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK)
begin
if (S_VALID & s_ready_i)
storage_data <= S_PAYLOAD_DATA;
end
assign M_PAYLOAD_DATA = storage_data;
// M_Valid set to high when we have a completed transfer on slave side
// Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK)
begin
if (~aresetn_d)
m_valid_i <= 1'b0;
else
if (S_VALID) // Always set m_valid_i when slave side is valid
m_valid_i <= 1'b1;
else
if (M_READY) // Clear (or keep) when no slave side is valid but master side is ready
m_valid_i <= 1'b0;
end // always @ (posedge ACLK)
// Slave Ready is either when Master side drives M_Ready or we have space in our storage data
assign s_ready_i = (M_READY | ~m_valid_i) & aresetn_d;
end // if (C_REG_CONFIG == 2)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 3
// Only REV mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000003)
begin
reg [C_DATA_WIDTH-1:0] storage_data;
reg s_ready_i; //local signal of output
reg has_valid_storage_i;
reg has_valid_storage;
reg [1:0] aresetn_d = 2'b00; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
// Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK)
begin
if (S_VALID & s_ready_i)
storage_data <= S_PAYLOAD_DATA;
end
assign M_PAYLOAD_DATA = has_valid_storage?storage_data:S_PAYLOAD_DATA;
// Need to determine when we need to save a payload
// Need a combinatorial signals since it will also effect S_READY
always @ *
begin
// Set the value if we have a slave transaction but master side is not ready
if (S_VALID & s_ready_i & ~M_READY)
has_valid_storage_i = 1'b1;
// Clear the value if it's set and Master side completes the transaction but we don't have a new slave side
// transaction
else if ( (has_valid_storage == 1) && (M_READY == 1) && ( (S_VALID == 0) || (s_ready_i == 0)))
has_valid_storage_i = 1'b0;
else
has_valid_storage_i = has_valid_storage;
end // always @ *
always @(posedge ACLK)
begin
if (~aresetn_d[0])
has_valid_storage <= 1'b0;
else
has_valid_storage <= has_valid_storage_i;
end
// S_READY is either clocked M_READY or that we have room in local storage
always @(posedge ACLK)
begin
if (~aresetn_d[0])
s_ready_i <= 1'b0;
else
s_ready_i <= M_READY | ~has_valid_storage_i;
end
// assign local signal to its output signal
assign S_READY = s_ready_i;
// M_READY is either combinatorial S_READY or that we have valid data in local storage
assign M_VALID = (S_VALID | has_valid_storage) & aresetn_d[1];
end // if (C_REG_CONFIG == 3)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 4 or 5 is NO LONGER SUPPORTED
//
////////////////////////////////////////////////////////////////////
else if ((C_REG_CONFIG == 32'h00000004) || (C_REG_CONFIG == 32'h00000005))
begin
// synthesis translate_off
initial begin
$display ("ERROR: For axi_register_slice, C_REG_CONFIG = 4 or 5 is RESERVED.");
end
// synthesis translate_on
assign M_PAYLOAD_DATA = 0;
assign M_VALID = 1'b0;
assign S_READY = 1'b0;
end
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 6
// INPUTS mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000006)
begin
reg [1:0] state;
reg [1:0] next_state;
localparam [1:0]
ZERO = 2'b00,
ONE = 2'b01,
TWO = 2'b11;
reg [C_DATA_WIDTH-1:0] storage_data1;
reg [C_DATA_WIDTH-1:0] storage_data2;
reg s_valid_d;
reg s_ready_d;
reg m_ready_d;
reg m_valid_d;
reg load_s2;
reg sel_s2;
wire new_access;
wire access_done;
wire s_ready_i; //local signal of output
reg s_ready_ii;
reg m_valid_i; //local signal of output
reg [1:0] aresetn_d = 2'b00; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
// assign local signal to its output signal
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign s_ready_i = s_ready_ii & aresetn_d[1];
// Registrate input control signals
always @(posedge ACLK)
begin
if (~aresetn_d[0]) begin
s_valid_d <= 1'b0;
s_ready_d <= 1'b0;
m_ready_d <= 1'b0;
end else begin
s_valid_d <= S_VALID;
s_ready_d <= s_ready_i;
m_ready_d <= M_READY;
end
end // always @ (posedge ACLK)
// Load storage1 with slave side payload data when slave side ready is high
always @(posedge ACLK)
begin
if (s_ready_i)
storage_data1 <= S_PAYLOAD_DATA;
end
// Load storage2 with storage data
always @(posedge ACLK)
begin
if (load_s2)
storage_data2 <= storage_data1;
end
always @(posedge ACLK)
begin
if (~aresetn_d[0])
m_valid_d <= 1'b0;
else
m_valid_d <= m_valid_i;
end
// Local help signals
assign new_access = s_ready_d & s_valid_d;
assign access_done = m_ready_d & m_valid_d;
// State Machine for handling output signals
always @*
begin
next_state = state; // Stay in the same state unless we need to move to another state
load_s2 = 0;
sel_s2 = 0;
m_valid_i = 0;
s_ready_ii = 0;
case (state)
// No transaction stored locally
ZERO: begin
load_s2 = 0;
sel_s2 = 0;
m_valid_i = 0;
s_ready_ii = 1;
if (new_access) begin
next_state = ONE; // Got one so move to ONE
load_s2 = 1;
m_valid_i = 0;
end
else begin
next_state = next_state;
load_s2 = load_s2;
m_valid_i = m_valid_i;
end
end // case: ZERO
// One transaction stored locally
ONE: begin
load_s2 = 0;
sel_s2 = 1;
m_valid_i = 1;
s_ready_ii = 1;
if (~new_access & access_done) begin
next_state = ZERO; // Read out one so move to ZERO
m_valid_i = 0;
end
else if (new_access & ~access_done) begin
next_state = TWO; // Got another one so move to TWO
s_ready_ii = 0;
end
else if (new_access & access_done) begin
load_s2 = 1;
sel_s2 = 0;
end
else begin
load_s2 = load_s2;
sel_s2 = sel_s2;
end
end // case: ONE
// TWO transaction stored locally
TWO: begin
load_s2 = 0;
sel_s2 = 1;
m_valid_i = 1;
s_ready_ii = 0;
if (access_done) begin
next_state = ONE; // Read out one so move to ONE
s_ready_ii = 1;
load_s2 = 1;
sel_s2 = 0;
end
else begin
next_state = next_state;
s_ready_ii = s_ready_ii;
load_s2 = load_s2;
sel_s2 = sel_s2;
end
end // case: TWO
endcase // case (state)
end // always @ *
// State Machine for handling output signals
always @(posedge ACLK)
begin
if (~aresetn_d[0])
state <= ZERO;
else
state <= next_state; // Stay in the same state unless we need to move to another state
end
// Master Payload mux
assign M_PAYLOAD_DATA = sel_s2?storage_data2:storage_data1;
end // if (C_REG_CONFIG == 6)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 7
// Light-weight mode.
// 1-stage pipeline register with bubble cycle, both FWD and REV pipelining
// Operates same as 1-deep FIFO
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000007) begin
reg [C_DATA_WIDTH-1:0] m_payload_i;
reg s_ready_i;
reg m_valid_i;
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign M_PAYLOAD_DATA = m_payload_i;
reg [1:0] aresetn_d = 2'b00; // Reset delay shifter
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
always @(posedge ACLK) begin
if (~aresetn_d[0]) begin
s_ready_i <= 1'b0;
end else if (~aresetn_d[1]) begin
s_ready_i <= 1'b1;
end else begin
s_ready_i <= m_valid_i ? M_READY : ~S_VALID;
end
if (~aresetn_d[1]) begin
m_valid_i <= 1'b0;
end else begin
m_valid_i <= s_ready_i ? S_VALID : ~M_READY;
end
if (~m_valid_i) begin
m_payload_i <= S_PAYLOAD_DATA;
end
end
end // if (C_REG_CONFIG == 7)
else begin : default_case
// Passthrough
assign M_PAYLOAD_DATA = S_PAYLOAD_DATA;
assign M_VALID = S_VALID;
assign S_READY = M_READY;
end
endgenerate
endmodule // reg_slice
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Register Slice
// Generic single-channel AXI pipeline register on forward and/or reverse signal path
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// axic_register_slice
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_register_slice_v2_1_axic_register_slice #
(
parameter C_FAMILY = "virtex6",
parameter C_DATA_WIDTH = 32,
parameter C_REG_CONFIG = 32'h00000000
// C_REG_CONFIG:
// 0 => BYPASS = The channel is just wired through the module.
// 1 => FWD_REV = Both FWD and REV (fully-registered)
// 2 => FWD = The master VALID and payload signals are registrated.
// 3 => REV = The slave ready signal is registrated
// 4 => RESERVED (all outputs driven to 0).
// 5 => RESERVED (all outputs driven to 0).
// 6 => INPUTS = Slave and Master side inputs are registrated.
// 7 => LIGHT_WT = 1-stage pipeline register with bubble cycle, both FWD and REV pipelining
)
(
// System Signals
input wire ACLK,
input wire ARESET,
// Slave side
input wire [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
input wire S_VALID,
output wire S_READY,
// Master side
output wire [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA,
output wire M_VALID,
input wire M_READY
);
(* use_clock_enable = "yes" *)
generate
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 0
// Bypass mode
//
////////////////////////////////////////////////////////////////////
if (C_REG_CONFIG == 32'h00000000) begin
assign M_PAYLOAD_DATA = S_PAYLOAD_DATA;
assign M_VALID = S_VALID;
assign S_READY = M_READY;
end
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 1 (or 8)
// Both FWD and REV mode
//
////////////////////////////////////////////////////////////////////
else if ((C_REG_CONFIG == 32'h00000001) || (C_REG_CONFIG == 32'h00000008)) begin
reg [C_DATA_WIDTH-1:0] m_payload_i;
reg [C_DATA_WIDTH-1:0] skid_buffer;
reg s_ready_i;
reg m_valid_i;
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign M_PAYLOAD_DATA = m_payload_i;
reg [1:0] aresetn_d = 2'b00; // Reset delay shifter
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
always @(posedge ACLK) begin
if (~aresetn_d[0]) begin
s_ready_i <= 1'b0;
end else begin
s_ready_i <= M_READY | ~m_valid_i | (s_ready_i & ~S_VALID);
end
if (~aresetn_d[1]) begin
m_valid_i <= 1'b0;
end else begin
m_valid_i <= S_VALID | ~s_ready_i | (m_valid_i & ~M_READY);
end
if (M_READY | ~m_valid_i) begin
m_payload_i <= s_ready_i ? S_PAYLOAD_DATA : skid_buffer;
end
if (s_ready_i) begin
skid_buffer <= S_PAYLOAD_DATA;
end
end
end // if (C_REG_CONFIG == 1)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 2
// Only FWD mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000002)
begin
reg [C_DATA_WIDTH-1:0] storage_data;
wire s_ready_i; //local signal of output
reg m_valid_i; //local signal of output
// assign local signal to its output signal
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
reg aresetn_d = 1'b0; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 1'b0;
end else begin
aresetn_d <= ~ARESET;
end
end
// Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK)
begin
if (S_VALID & s_ready_i)
storage_data <= S_PAYLOAD_DATA;
end
assign M_PAYLOAD_DATA = storage_data;
// M_Valid set to high when we have a completed transfer on slave side
// Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK)
begin
if (~aresetn_d)
m_valid_i <= 1'b0;
else
if (S_VALID) // Always set m_valid_i when slave side is valid
m_valid_i <= 1'b1;
else
if (M_READY) // Clear (or keep) when no slave side is valid but master side is ready
m_valid_i <= 1'b0;
end // always @ (posedge ACLK)
// Slave Ready is either when Master side drives M_Ready or we have space in our storage data
assign s_ready_i = (M_READY | ~m_valid_i) & aresetn_d;
end // if (C_REG_CONFIG == 2)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 3
// Only REV mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000003)
begin
reg [C_DATA_WIDTH-1:0] storage_data;
reg s_ready_i; //local signal of output
reg has_valid_storage_i;
reg has_valid_storage;
reg [1:0] aresetn_d = 2'b00; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
// Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK)
begin
if (S_VALID & s_ready_i)
storage_data <= S_PAYLOAD_DATA;
end
assign M_PAYLOAD_DATA = has_valid_storage?storage_data:S_PAYLOAD_DATA;
// Need to determine when we need to save a payload
// Need a combinatorial signals since it will also effect S_READY
always @ *
begin
// Set the value if we have a slave transaction but master side is not ready
if (S_VALID & s_ready_i & ~M_READY)
has_valid_storage_i = 1'b1;
// Clear the value if it's set and Master side completes the transaction but we don't have a new slave side
// transaction
else if ( (has_valid_storage == 1) && (M_READY == 1) && ( (S_VALID == 0) || (s_ready_i == 0)))
has_valid_storage_i = 1'b0;
else
has_valid_storage_i = has_valid_storage;
end // always @ *
always @(posedge ACLK)
begin
if (~aresetn_d[0])
has_valid_storage <= 1'b0;
else
has_valid_storage <= has_valid_storage_i;
end
// S_READY is either clocked M_READY or that we have room in local storage
always @(posedge ACLK)
begin
if (~aresetn_d[0])
s_ready_i <= 1'b0;
else
s_ready_i <= M_READY | ~has_valid_storage_i;
end
// assign local signal to its output signal
assign S_READY = s_ready_i;
// M_READY is either combinatorial S_READY or that we have valid data in local storage
assign M_VALID = (S_VALID | has_valid_storage) & aresetn_d[1];
end // if (C_REG_CONFIG == 3)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 4 or 5 is NO LONGER SUPPORTED
//
////////////////////////////////////////////////////////////////////
else if ((C_REG_CONFIG == 32'h00000004) || (C_REG_CONFIG == 32'h00000005))
begin
// synthesis translate_off
initial begin
$display ("ERROR: For axi_register_slice, C_REG_CONFIG = 4 or 5 is RESERVED.");
end
// synthesis translate_on
assign M_PAYLOAD_DATA = 0;
assign M_VALID = 1'b0;
assign S_READY = 1'b0;
end
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 6
// INPUTS mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000006)
begin
reg [1:0] state;
reg [1:0] next_state;
localparam [1:0]
ZERO = 2'b00,
ONE = 2'b01,
TWO = 2'b11;
reg [C_DATA_WIDTH-1:0] storage_data1;
reg [C_DATA_WIDTH-1:0] storage_data2;
reg s_valid_d;
reg s_ready_d;
reg m_ready_d;
reg m_valid_d;
reg load_s2;
reg sel_s2;
wire new_access;
wire access_done;
wire s_ready_i; //local signal of output
reg s_ready_ii;
reg m_valid_i; //local signal of output
reg [1:0] aresetn_d = 2'b00; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
// assign local signal to its output signal
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign s_ready_i = s_ready_ii & aresetn_d[1];
// Registrate input control signals
always @(posedge ACLK)
begin
if (~aresetn_d[0]) begin
s_valid_d <= 1'b0;
s_ready_d <= 1'b0;
m_ready_d <= 1'b0;
end else begin
s_valid_d <= S_VALID;
s_ready_d <= s_ready_i;
m_ready_d <= M_READY;
end
end // always @ (posedge ACLK)
// Load storage1 with slave side payload data when slave side ready is high
always @(posedge ACLK)
begin
if (s_ready_i)
storage_data1 <= S_PAYLOAD_DATA;
end
// Load storage2 with storage data
always @(posedge ACLK)
begin
if (load_s2)
storage_data2 <= storage_data1;
end
always @(posedge ACLK)
begin
if (~aresetn_d[0])
m_valid_d <= 1'b0;
else
m_valid_d <= m_valid_i;
end
// Local help signals
assign new_access = s_ready_d & s_valid_d;
assign access_done = m_ready_d & m_valid_d;
// State Machine for handling output signals
always @*
begin
next_state = state; // Stay in the same state unless we need to move to another state
load_s2 = 0;
sel_s2 = 0;
m_valid_i = 0;
s_ready_ii = 0;
case (state)
// No transaction stored locally
ZERO: begin
load_s2 = 0;
sel_s2 = 0;
m_valid_i = 0;
s_ready_ii = 1;
if (new_access) begin
next_state = ONE; // Got one so move to ONE
load_s2 = 1;
m_valid_i = 0;
end
else begin
next_state = next_state;
load_s2 = load_s2;
m_valid_i = m_valid_i;
end
end // case: ZERO
// One transaction stored locally
ONE: begin
load_s2 = 0;
sel_s2 = 1;
m_valid_i = 1;
s_ready_ii = 1;
if (~new_access & access_done) begin
next_state = ZERO; // Read out one so move to ZERO
m_valid_i = 0;
end
else if (new_access & ~access_done) begin
next_state = TWO; // Got another one so move to TWO
s_ready_ii = 0;
end
else if (new_access & access_done) begin
load_s2 = 1;
sel_s2 = 0;
end
else begin
load_s2 = load_s2;
sel_s2 = sel_s2;
end
end // case: ONE
// TWO transaction stored locally
TWO: begin
load_s2 = 0;
sel_s2 = 1;
m_valid_i = 1;
s_ready_ii = 0;
if (access_done) begin
next_state = ONE; // Read out one so move to ONE
s_ready_ii = 1;
load_s2 = 1;
sel_s2 = 0;
end
else begin
next_state = next_state;
s_ready_ii = s_ready_ii;
load_s2 = load_s2;
sel_s2 = sel_s2;
end
end // case: TWO
endcase // case (state)
end // always @ *
// State Machine for handling output signals
always @(posedge ACLK)
begin
if (~aresetn_d[0])
state <= ZERO;
else
state <= next_state; // Stay in the same state unless we need to move to another state
end
// Master Payload mux
assign M_PAYLOAD_DATA = sel_s2?storage_data2:storage_data1;
end // if (C_REG_CONFIG == 6)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 7
// Light-weight mode.
// 1-stage pipeline register with bubble cycle, both FWD and REV pipelining
// Operates same as 1-deep FIFO
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000007) begin
reg [C_DATA_WIDTH-1:0] m_payload_i;
reg s_ready_i;
reg m_valid_i;
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign M_PAYLOAD_DATA = m_payload_i;
reg [1:0] aresetn_d = 2'b00; // Reset delay shifter
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
always @(posedge ACLK) begin
if (~aresetn_d[0]) begin
s_ready_i <= 1'b0;
end else if (~aresetn_d[1]) begin
s_ready_i <= 1'b1;
end else begin
s_ready_i <= m_valid_i ? M_READY : ~S_VALID;
end
if (~aresetn_d[1]) begin
m_valid_i <= 1'b0;
end else begin
m_valid_i <= s_ready_i ? S_VALID : ~M_READY;
end
if (~m_valid_i) begin
m_payload_i <= S_PAYLOAD_DATA;
end
end
end // if (C_REG_CONFIG == 7)
else begin : default_case
// Passthrough
assign M_PAYLOAD_DATA = S_PAYLOAD_DATA;
assign M_VALID = S_VALID;
assign S_READY = M_READY;
end
endgenerate
endmodule // reg_slice
|
// -- (c) Copyright 2010 - 2011 Xilinx, Inc. All rights reserved.
// --
// -- This file contains confidential and proprietary information
// -- of Xilinx, Inc. and is protected under U.S. and
// -- international copyright and other intellectual property
// -- laws.
// --
// -- DISCLAIMER
// -- This disclaimer is not a license and does not grant any
// -- rights to the materials distributed herewith. Except as
// -- otherwise provided in a valid license issued to you by
// -- Xilinx, and to the maximum extent permitted by applicable
// -- law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// -- WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// -- AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// -- BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// -- INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// -- (2) Xilinx shall not be liable (whether in contract or tort,
// -- including negligence, or under any other theory of
// -- liability) for any loss or damage of any kind or nature
// -- related to, arising under or in connection with these
// -- materials, including for any direct, or any indirect,
// -- special, incidental, or consequential loss or damage
// -- (including loss of data, profits, goodwill, or any type of
// -- loss or damage suffered as a result of any action brought
// -- by a third party) even if such damage or loss was
// -- reasonably foreseeable or Xilinx had been advised of the
// -- possibility of the same.
// --
// -- CRITICAL APPLICATIONS
// -- Xilinx products are not designed or intended to be fail-
// -- safe, or for use in any application requiring fail-safe
// -- performance, such as life-support or safety devices or
// -- systems, Class III medical devices, nuclear facilities,
// -- applications related to the deployment of airbags, or any
// -- other applications that could lead to death, personal
// -- injury, or severe property or environmental damage
// -- (individually and collectively, "Critical
// -- Applications"). Customer assumes the sole risk and
// -- liability of any use of Xilinx products in Critical
// -- Applications, subject only to applicable laws and
// -- regulations governing limitations on product liability.
// --
// -- THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// -- PART OF THIS FILE AT ALL TIMES.
//-----------------------------------------------------------------------------
//
// Register Slice
// Generic single-channel AXI pipeline register on forward and/or reverse signal path
//
// Verilog-standard: Verilog 2001
//--------------------------------------------------------------------------
//
// Structure:
// axic_register_slice
//
//--------------------------------------------------------------------------
`timescale 1ps/1ps
(* DowngradeIPIdentifiedWarnings="yes" *)
module axi_register_slice_v2_1_axic_register_slice #
(
parameter C_FAMILY = "virtex6",
parameter C_DATA_WIDTH = 32,
parameter C_REG_CONFIG = 32'h00000000
// C_REG_CONFIG:
// 0 => BYPASS = The channel is just wired through the module.
// 1 => FWD_REV = Both FWD and REV (fully-registered)
// 2 => FWD = The master VALID and payload signals are registrated.
// 3 => REV = The slave ready signal is registrated
// 4 => RESERVED (all outputs driven to 0).
// 5 => RESERVED (all outputs driven to 0).
// 6 => INPUTS = Slave and Master side inputs are registrated.
// 7 => LIGHT_WT = 1-stage pipeline register with bubble cycle, both FWD and REV pipelining
)
(
// System Signals
input wire ACLK,
input wire ARESET,
// Slave side
input wire [C_DATA_WIDTH-1:0] S_PAYLOAD_DATA,
input wire S_VALID,
output wire S_READY,
// Master side
output wire [C_DATA_WIDTH-1:0] M_PAYLOAD_DATA,
output wire M_VALID,
input wire M_READY
);
(* use_clock_enable = "yes" *)
generate
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 0
// Bypass mode
//
////////////////////////////////////////////////////////////////////
if (C_REG_CONFIG == 32'h00000000) begin
assign M_PAYLOAD_DATA = S_PAYLOAD_DATA;
assign M_VALID = S_VALID;
assign S_READY = M_READY;
end
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 1 (or 8)
// Both FWD and REV mode
//
////////////////////////////////////////////////////////////////////
else if ((C_REG_CONFIG == 32'h00000001) || (C_REG_CONFIG == 32'h00000008)) begin
reg [C_DATA_WIDTH-1:0] m_payload_i;
reg [C_DATA_WIDTH-1:0] skid_buffer;
reg s_ready_i;
reg m_valid_i;
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign M_PAYLOAD_DATA = m_payload_i;
reg [1:0] aresetn_d = 2'b00; // Reset delay shifter
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
always @(posedge ACLK) begin
if (~aresetn_d[0]) begin
s_ready_i <= 1'b0;
end else begin
s_ready_i <= M_READY | ~m_valid_i | (s_ready_i & ~S_VALID);
end
if (~aresetn_d[1]) begin
m_valid_i <= 1'b0;
end else begin
m_valid_i <= S_VALID | ~s_ready_i | (m_valid_i & ~M_READY);
end
if (M_READY | ~m_valid_i) begin
m_payload_i <= s_ready_i ? S_PAYLOAD_DATA : skid_buffer;
end
if (s_ready_i) begin
skid_buffer <= S_PAYLOAD_DATA;
end
end
end // if (C_REG_CONFIG == 1)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 2
// Only FWD mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000002)
begin
reg [C_DATA_WIDTH-1:0] storage_data;
wire s_ready_i; //local signal of output
reg m_valid_i; //local signal of output
// assign local signal to its output signal
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
reg aresetn_d = 1'b0; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 1'b0;
end else begin
aresetn_d <= ~ARESET;
end
end
// Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK)
begin
if (S_VALID & s_ready_i)
storage_data <= S_PAYLOAD_DATA;
end
assign M_PAYLOAD_DATA = storage_data;
// M_Valid set to high when we have a completed transfer on slave side
// Is removed on a M_READY except if we have a new transfer on the slave side
always @(posedge ACLK)
begin
if (~aresetn_d)
m_valid_i <= 1'b0;
else
if (S_VALID) // Always set m_valid_i when slave side is valid
m_valid_i <= 1'b1;
else
if (M_READY) // Clear (or keep) when no slave side is valid but master side is ready
m_valid_i <= 1'b0;
end // always @ (posedge ACLK)
// Slave Ready is either when Master side drives M_Ready or we have space in our storage data
assign s_ready_i = (M_READY | ~m_valid_i) & aresetn_d;
end // if (C_REG_CONFIG == 2)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 3
// Only REV mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000003)
begin
reg [C_DATA_WIDTH-1:0] storage_data;
reg s_ready_i; //local signal of output
reg has_valid_storage_i;
reg has_valid_storage;
reg [1:0] aresetn_d = 2'b00; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
// Save payload data whenever we have a transaction on the slave side
always @(posedge ACLK)
begin
if (S_VALID & s_ready_i)
storage_data <= S_PAYLOAD_DATA;
end
assign M_PAYLOAD_DATA = has_valid_storage?storage_data:S_PAYLOAD_DATA;
// Need to determine when we need to save a payload
// Need a combinatorial signals since it will also effect S_READY
always @ *
begin
// Set the value if we have a slave transaction but master side is not ready
if (S_VALID & s_ready_i & ~M_READY)
has_valid_storage_i = 1'b1;
// Clear the value if it's set and Master side completes the transaction but we don't have a new slave side
// transaction
else if ( (has_valid_storage == 1) && (M_READY == 1) && ( (S_VALID == 0) || (s_ready_i == 0)))
has_valid_storage_i = 1'b0;
else
has_valid_storage_i = has_valid_storage;
end // always @ *
always @(posedge ACLK)
begin
if (~aresetn_d[0])
has_valid_storage <= 1'b0;
else
has_valid_storage <= has_valid_storage_i;
end
// S_READY is either clocked M_READY or that we have room in local storage
always @(posedge ACLK)
begin
if (~aresetn_d[0])
s_ready_i <= 1'b0;
else
s_ready_i <= M_READY | ~has_valid_storage_i;
end
// assign local signal to its output signal
assign S_READY = s_ready_i;
// M_READY is either combinatorial S_READY or that we have valid data in local storage
assign M_VALID = (S_VALID | has_valid_storage) & aresetn_d[1];
end // if (C_REG_CONFIG == 3)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 4 or 5 is NO LONGER SUPPORTED
//
////////////////////////////////////////////////////////////////////
else if ((C_REG_CONFIG == 32'h00000004) || (C_REG_CONFIG == 32'h00000005))
begin
// synthesis translate_off
initial begin
$display ("ERROR: For axi_register_slice, C_REG_CONFIG = 4 or 5 is RESERVED.");
end
// synthesis translate_on
assign M_PAYLOAD_DATA = 0;
assign M_VALID = 1'b0;
assign S_READY = 1'b0;
end
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 6
// INPUTS mode
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000006)
begin
reg [1:0] state;
reg [1:0] next_state;
localparam [1:0]
ZERO = 2'b00,
ONE = 2'b01,
TWO = 2'b11;
reg [C_DATA_WIDTH-1:0] storage_data1;
reg [C_DATA_WIDTH-1:0] storage_data2;
reg s_valid_d;
reg s_ready_d;
reg m_ready_d;
reg m_valid_d;
reg load_s2;
reg sel_s2;
wire new_access;
wire access_done;
wire s_ready_i; //local signal of output
reg s_ready_ii;
reg m_valid_i; //local signal of output
reg [1:0] aresetn_d = 2'b00; // Reset delay register
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
// assign local signal to its output signal
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign s_ready_i = s_ready_ii & aresetn_d[1];
// Registrate input control signals
always @(posedge ACLK)
begin
if (~aresetn_d[0]) begin
s_valid_d <= 1'b0;
s_ready_d <= 1'b0;
m_ready_d <= 1'b0;
end else begin
s_valid_d <= S_VALID;
s_ready_d <= s_ready_i;
m_ready_d <= M_READY;
end
end // always @ (posedge ACLK)
// Load storage1 with slave side payload data when slave side ready is high
always @(posedge ACLK)
begin
if (s_ready_i)
storage_data1 <= S_PAYLOAD_DATA;
end
// Load storage2 with storage data
always @(posedge ACLK)
begin
if (load_s2)
storage_data2 <= storage_data1;
end
always @(posedge ACLK)
begin
if (~aresetn_d[0])
m_valid_d <= 1'b0;
else
m_valid_d <= m_valid_i;
end
// Local help signals
assign new_access = s_ready_d & s_valid_d;
assign access_done = m_ready_d & m_valid_d;
// State Machine for handling output signals
always @*
begin
next_state = state; // Stay in the same state unless we need to move to another state
load_s2 = 0;
sel_s2 = 0;
m_valid_i = 0;
s_ready_ii = 0;
case (state)
// No transaction stored locally
ZERO: begin
load_s2 = 0;
sel_s2 = 0;
m_valid_i = 0;
s_ready_ii = 1;
if (new_access) begin
next_state = ONE; // Got one so move to ONE
load_s2 = 1;
m_valid_i = 0;
end
else begin
next_state = next_state;
load_s2 = load_s2;
m_valid_i = m_valid_i;
end
end // case: ZERO
// One transaction stored locally
ONE: begin
load_s2 = 0;
sel_s2 = 1;
m_valid_i = 1;
s_ready_ii = 1;
if (~new_access & access_done) begin
next_state = ZERO; // Read out one so move to ZERO
m_valid_i = 0;
end
else if (new_access & ~access_done) begin
next_state = TWO; // Got another one so move to TWO
s_ready_ii = 0;
end
else if (new_access & access_done) begin
load_s2 = 1;
sel_s2 = 0;
end
else begin
load_s2 = load_s2;
sel_s2 = sel_s2;
end
end // case: ONE
// TWO transaction stored locally
TWO: begin
load_s2 = 0;
sel_s2 = 1;
m_valid_i = 1;
s_ready_ii = 0;
if (access_done) begin
next_state = ONE; // Read out one so move to ONE
s_ready_ii = 1;
load_s2 = 1;
sel_s2 = 0;
end
else begin
next_state = next_state;
s_ready_ii = s_ready_ii;
load_s2 = load_s2;
sel_s2 = sel_s2;
end
end // case: TWO
endcase // case (state)
end // always @ *
// State Machine for handling output signals
always @(posedge ACLK)
begin
if (~aresetn_d[0])
state <= ZERO;
else
state <= next_state; // Stay in the same state unless we need to move to another state
end
// Master Payload mux
assign M_PAYLOAD_DATA = sel_s2?storage_data2:storage_data1;
end // if (C_REG_CONFIG == 6)
////////////////////////////////////////////////////////////////////
//
// C_REG_CONFIG = 7
// Light-weight mode.
// 1-stage pipeline register with bubble cycle, both FWD and REV pipelining
// Operates same as 1-deep FIFO
//
////////////////////////////////////////////////////////////////////
else if (C_REG_CONFIG == 32'h00000007) begin
reg [C_DATA_WIDTH-1:0] m_payload_i;
reg s_ready_i;
reg m_valid_i;
assign S_READY = s_ready_i;
assign M_VALID = m_valid_i;
assign M_PAYLOAD_DATA = m_payload_i;
reg [1:0] aresetn_d = 2'b00; // Reset delay shifter
always @(posedge ACLK) begin
if (ARESET) begin
aresetn_d <= 2'b00;
end else begin
aresetn_d <= {aresetn_d[0], ~ARESET};
end
end
always @(posedge ACLK) begin
if (~aresetn_d[0]) begin
s_ready_i <= 1'b0;
end else if (~aresetn_d[1]) begin
s_ready_i <= 1'b1;
end else begin
s_ready_i <= m_valid_i ? M_READY : ~S_VALID;
end
if (~aresetn_d[1]) begin
m_valid_i <= 1'b0;
end else begin
m_valid_i <= s_ready_i ? S_VALID : ~M_READY;
end
if (~m_valid_i) begin
m_payload_i <= S_PAYLOAD_DATA;
end
end
end // if (C_REG_CONFIG == 7)
else begin : default_case
// Passthrough
assign M_PAYLOAD_DATA = S_PAYLOAD_DATA;
assign M_VALID = S_VALID;
assign S_READY = M_READY;
end
endgenerate
endmodule // reg_slice
|
Subsets and Splits
No saved queries yet
Save your SQL queries to embed, download, and access them later. Queries will appear here once saved.